SIGNATURE HARDWARE 434357 Whitby Outdoor Wall Sconce Instruction Manual
- June 10, 2024
- Signature Hardware
Table of Contents
SIGNATURE HARDWARE 434357 Whitby Outdoor Wall Sconce
Product Information
The Whitby (SKU: 941512) is an electric fixture designed for installation in bathrooms or other indoor spaces. The fixture includes a mounting plate, fixture, wire connectors, mounting screws, ground screws, and cap nuts. The product is fragile and must be handled with care during installation and cleaning. Before installing, ensure that all required materials are gathered and local plumbing and building codes are observed. Signature Hardware does not accept liability for any damage to the faucet, plumbing, sink, countertop, or personal injury during installation.
Product Usage Instructions
- Consult a professional if unfamiliar with installing electric fixtures.
- Shut off the power at the circuit breaker and remove old fixtures, including the crossbar.
- Unpack and inspect the product for shipping damage. Lay out all parts in a clear area, taking care not to lose any small parts necessary for installation.
- Thread the 2 Mounting Screws to the Mounting plate. Adjust the length of the screws if necessary.
- Attach the Mounting plate to the Outlet Box (not supplied) by using 2 Outlet Box Screws.
- Attach the Fixture to the Mounting Plate by inserting the 2 Mounting Screws, and then secure it with the 2 Cap Nuts.
- To prevent moisture from entering the outlet box and causing a short, use clear caulking (indoor/outdoor silicone sealant) to outline the outside of the fixture backplate where it meets the wall leaving a space at the bottom to allow moisture a means to escape.
- Clean with a damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.
- If you have additional questions, check out our Help Center or contact customer support through live chat or email.
BEFORE YOU BEGIN
We recommend consulting a professional if you are unfamiliar with installing electric fixtures. Signature Hardware accepts no liability for any damage to the faucet, plumbing, sink, or countertop, or for personal injury during installation. Observe all local plumbing and building codes. Unpack and inspect the product for shipping damage. If any damage is found, contact our Customer Relations team via live chat at www.signaturehardware. com or by emailing support@siganturehardware.com.
GETTING STARTED
Ensure that you have gathered all the required materials that are needed for the installation.
ADDITIONAL QUESTIONS?
Still, need help? Check out our Help Center at www.signaturehardware.com for product and warranty information, or contact us through live chat or by emailing support@signaturehardware.com.
WHITBY
- OUTDOOR WALL SCONCE
- SKU: 941512
CARE AND MAINTENANCE
To clean, wipe with a damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.
CAUTION
Shut off the main power supply before cleaning the product or changing light bulbs. All glass is fragile. Use care when handling glass shades and bulbs.
RECOMMENDED TOOLS AND ACCESSORIES
- Wire Connectors (3pcs)
- Outlet Box Screws (2pcs)
- Mounting Screws (2pcs)
- Ground Screw (1pc)
- Mounting plate (1pc)
- Cap Nuts (2pcs)
OUTDOOR WALL SCONCE
- SKU: 941512
SAVE THIS MANUAL: RETAIN FOR CONSUMER’S USE. READ THESE INSTRUCTIONS COMPLETELY BEFORE INSTALLING THE PRODUCT: FOR PRODUCT OR INSTALLATION QUESTIONS PLEASE CALL THE CUSTOMER. SERVICE AT 1-800-221-3379.
INSTALLATION
- Shut off the power at the circuit breaker and remove the old fixture, including the crossbar.
- Carefully unpack your new fixture and lay out all the parts in a clear area. Take care not to lose any small parts necessary for installation.
- Thread the 2 Mounting Screws (C) to the Mounting plate (E). (You can adjust the length of the screws if necessary.)
- Attach the Mounting plate (E) to the Outlet Box (G) (not supplied) by using 2 Outlet Box Screws (B).
- Now connect the electrical wires as follows: Connect the black wire from the fixture to the black house (hot) wire. Connect the white wire from the fixture to the white (neutral) house wire. Make sure all wire nuts are secured. You may wrap the connections with electrical tape. If your outlet has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate using the green screw provided. Tuck the wire connections neatly into the junction box.
- Attach the Fixture (H) to the Mounting Plate by inserting the 2 Mounting Screws (C), and then secure it with the 2 Cap Nuts (F).
- To prevent moisture from entering the outlet box and causing a short, use clear caulking (ie. Indoor/Outdoor Silicone Sealant) to outline the outside of the fixture backplate where it meets the wall leaving a space at the bottom to allow moisture a means to escape.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>