SIGNATURE HARDWARE 440758 BARWELL Sconce Wall Lamp Sconce Murale User Manual

June 10, 2024
Signature Hardware

SIGNATURE HARDWARE 440758 BARWELL Sconce Wall Lamp Sconce Murale

Product Information

The BARWELL fixture (SKU: 440758, 440759) is an electric fixture that includes a circular strap, outlet box screws, glass cup, screws, and a light bulb socket with a maximum wattage capacity of 60 watts. The fixture requires the installation and should be carried out by a professional. Signature Hardware bears no responsibility for any damage to the fixture, plumbing, sink, or personal injury resulting from improper installation. It is essential to observe all local plumbing and building codes during installation.

Product Usage Instructions

  1. Gather all the necessary tools and materials required for the installation as listed in the manual – the light bulbs, safety glasses, wire strippers, screwdrivers, wire cutters, electrical tape, etc.
  2. Thread the mounting screws (A) into the matching holes in the circular strap (B).
  3. Secure the circular strap (B) to the outlet box with the outlet box screws (C).
  4. Connect the wires carefully and tuck them inside the outlet box. Raise the front plate (D) to allow for the mounting screws (A) to protrude.
  5. Raise the glass (H) to the cup (F) and secure it with screws (G).
  6. Install a light bulb with a maximum wattage capacity of 60 watts. Do not exceed the maximum wattage capacity recommended on the socket.
  7. If any shipping damage is found upon inspection, contact Signature Hardware’s Customer Relations team via live chat or email.

For additional product and warranty information or further assistance, refer to our Help Center at www.signaturehardware.com or contact the customer support team through live chat or by emailing support@signaturehardware.com.

BEFORE YOU BEGIN

We recommend consulting a professional if you are unfamiliar with installing electric fixtures. Signature Hardware accepts no liability for any damage to the faucet, plumbing, sink, or countertop, or for personal injury during installation. Observe all local plumbing and building codes. Unpack and inspect the product for shipping damage. If any damage is found, contact our Customer Relations team via live chat at www.signaturehardware.com or by emailing support@siganturehardware.com.

GETTING STARTED
Ensure that you have gathered all the required materials that are needed for the installation.

ADDITIONAL QUESTIONS?
Still need help? Check out our Help Center at www.signaturehardware.com for product and warranty information, or contact us through live chat or by emailing support@signaturehardware.com.

FOR YOUR SAFETY

WARNING:
Be sure the electricity to the wires you are working on is shut off, either the fuse is removed or the circuit breaker is shut off. You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling that contains a radiant- type heating system. Read instructions carefully, if you are unclear as to how to proceed, consult a qualified electrician.

TOOLS AND MATERIALS

INSTALLATION

(FIG. 1)

  1. Thread the mounting screws (A) into the matching holes in the circular strap (B).

  2. Secure circular trap (B) to the outlet box with outlet box screws (C).

  3. Connect the white wire from the fixture to the white wire from the outlet box and the black wire from the fixture to the black wire from the outlet box. Cover the two wire connections using the two provided wire connectors. Wrap the two wire connections with electrical tape for a more secure connection. Attach the grounding wire connections with electrical tape for a more secure connection. Connect the copper ground wires from the fixture and from the outlet box to the ground screw on the circular strap.
    Note: If you have electrical questions, consult your local electrical code for approved grounding methods.

  4. After the wires are connected, tuck them carefully inside the outlet box. Raise the front plate (D) allowing for the mounting screws (A) to protrude.

(FIG. 2)

  1. Raise the glass (H) to the cup (F) and secure with the screws (G).
  2. Install light bulb (Not provided). Please do not exceed the maximum wattage capacity recommended on the socket.

Contact Information

1.855.715.1800
signaturehardware.com.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Signature Hardware User Manuals

Related Manuals