namron 1402768 LED Dimmer TW ZigBee 250W Instruction Manual

: June 10, 2024
: NAMRON

Table of Contents

Function introduction
Product Data
Safety & Warnings
Operation
Wiring diagram
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Namron LED Dimmer TW ZigBee 250W
Instruction Manual

Important: Read All Instructions Prior to Installation

Function introduction

namron 1402768 LED Dimmer TW ZigBee 250W - Fig1

Product Data

Input Voltage	Output Voltage	Output Current	Size(LxWxH)
220-240V AC	220-240V AC	1.13A max	848457mm

ZigBee AC phase cut dimmer based on latest ZigBee 3.0 protocol
220V-240V AC Input and Output Voltage
Supports resistive loads and capacitive loads
Input and Output with Screw Terminals, Safe and Reliable
Trailing edge control
Enables to control ON/OFF and light intensity of connected triac dimmable led light or led driver
ZigBee end device that supports Touchline commissioning
Can directly pair to a compatible ZigBee remote via Touchline without coordinator
Supports self-forming zigbee network without coordinator and add other devices to the network
Supports find and bind mode to bind a ZigBee remote
Compatible with European trendy ZigBee gateway products
Can be controlled by universal 220V-240V input single wire push switch
Mini Size, Easy to be Installed into a standard 86*86mm wall box
Radio Frequency : 2.4GHz
Waterproof grade: IP20

Safety & Warnings

DO NOT install with power applied to device.
DO NOT expose the device to moisture.
DO NOT open the dimmer in case any damages that out of repair.

ZigBee Clusters the device supports are as follows: Input Clusters

0x0000: Basic
0x0003: Identify
0x0004: Groups
0x0005: Scenes
0x0006: On/off
0x0008: Level Control
0x0300:Color Control

Operation

Do wiring according to connection diagram correctly.
This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible systems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBee system.
Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)
Step 1: Remove the device from previous zigbee network if it has already been added to, otherwise pairing will fail. Please refer to the part “Factory Reset Manually”.
Step 2: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as instructed by the controller.
Touch Link to a Zigbee Remote Step 5: The connecting lights will start flashing to in dictate the pairing processing. Once paired both the connecting lights and the green indicator light will stop flashing
and you can control the lights by the remote.
Note :
Directly Touchline(both not added to a Zigbee network),each device can link with 1 remote.
Touchline after both added to a Zigbee network, each device can link with max.30 remotes.
For Hue Bridge & Amazon Echo Plus , add remote and device to network first then Touchline.
After Touchlink,the device can be controlled by the linked remotes.
Factory Reset Manually
Find and Bind Mode
Note: Make sure the device and remote already added to the same zigbee network.
Setup a Zigbee Network & Add Other Devices to the Network(No Coordinator Required)
Step 3 : Press the reset button for 7times to allow other devices to be added into the network.The red indicator light will be flashing continuously.
Step 4 : Set another device or remote or touch panel into network pairing mode and pair to the network, refer to their manuals. 180s time limit.
Step 5 : Pair more devices and remotes to the network as you would like, refer to their manuals.
Step 6 : Bind the added devices and remotes through Touchlink so that the devices can be controlled by the remotes, refer to their manuals.
Note:
Each added device can link and be controlled by max.30 added remotes.
Please refer to remote instruction of how many devices can be linked.