HAMOKI EP1+1 Pizza Oven Instruction Manual
- June 10, 2024
- HAMOKI
Table of Contents
HAMOKI EP1+1 Pizza Oven
Pizza Oven Product Information
The Pizza Oven comes in two models: EP1+1 and EP2+2. It operates on a
voltage of 220V~240V and has a power output of 37kg and 55kg for the EP1+1 and
EP2+2 models respectively. The oven has a landing bolt at the back, which can
be connected to a copper core wire (>2.5mm2) with a safe earth wire. The Pizza
Oven has a thermostat and an element that can be replaced if damaged.
Product Usage Instructions
Before operating the Pizza Oven, please ensure that you have read the instruction manual carefully.
Installation
- Make sure that the used voltage matches the rated voltage of the oven.
- Ensure that you have enough power to operate the unit.
- Connect the copper core wire with a safe earth wire to the landing bolt at the back of the oven.
- Inspect the wire, voltage, and landing wire to make sure they are safe and properly installed.
Troubleshooting
If you experience any issues with the Pizza Oven, please refer to the table below:
| Fault | Cause | Solution |
|---|
Power switch turned on with indicator light but temperature is
not increasing in the oven| 1. Thermostat is damaged
2. Element is damaged| 1. Change thermostat
2. Change element
Power switched on, unable to turn thermostat, temperature
cannot be controlled| The thermostat is damaged| Change the thermostat
Power on, switch is pressed, but indicator is not lighting
up| The indicator is damaged| Change the indicator
Power on, indicator not lighting up, temperature isn’t
increasing| Power not wired, damaged fuse| Inspect power and wire, change fuse
Warranty
The Pizza Oven comes with a warranty. Please refer to the instruction manual for details.
Please read this instruction manual carefully before operation
Control Panel
EP1+1
EP2+2
Instructions
-
A. The illuminating light switch controls the illuminating light in the oven.
B. Turn on the power switch. Regulate the bottom heater thermostat to needed temperature to heat.（the timer just remind not interrupt）The thermostat will keep a constant temperature when the temperature reaches set temperature. -
C. Turn off the power switch. Regulate the bottom heater thermostat to the required temperature. Then regulate the timer to the time needed. It will stop heating when it times out.(If using the timerplease increase the temperature to a set temperature）
-
D. The bottom heater thermostat is to control both the bottom element and the bottom indicator. The middle heater thermostat is to controlthe middle element and the middle indicator. The top heater thermostat is to control the top element and the top indicator.
-
E. The maximum temperature can reach 350℃ and the temperature increases rapidly.
-
F. You must preheat the temperature to 200-300℃ before putting the food in the oven.
Installation
- A. The used voltage must be the same as rated voltage.
- B．You must pull in enough power for the unit.
- C．There is a landing bolt at back of the oven. Connect the copper core wire (>2.5mm2 ) with safe earth wire.
- D. Inspect the wire, voltage, and the lading wire to be sure they are all safe and properly installed.
Waste Disposal:
At the end of its service life the d device has to be disposed of in
accordance with the national regulations. It is advisable to contact a company
which specialises in waste disposal, or contact the local disposal service in
your community.
WARNING! To avoid danger, make the device unfit for use before disposal. For that purpose, disconnect the device from the mains supply and remove the mains connection cable from the device. NOTE! For the disposal of the device please consider and act according to the national and local rules and regulations.
| Model | Code | Measurement | Power | Voltage | Weight |
|---|---|---|---|---|---|
| EP-2 | 171004 | 770×720×270mm | 2.2 kW | 220V~240V | 37kg |
| EP 2+2 | 171003 | 770×720×430mm | 3 kW | 220V~240V | 55kg |
Troubleshooting
| Fault | Cause | Solution |
|---|
Power switch turned on with indicator light but the temperature is not increasing in the oven| 1. Thermostat is damaged
2. element is damaged
| 1. change thermostat
2. change element
Power switched on, unable to turn the thermostat, temperature cannot be
controlled.| The thermostat is damaged| Change the thermostat
Power on, switch is pressed, but indicator is not lighting up| The indicator
is damaged| Change the indicator
Power on, indicator not lighting up, temperature isn’t increasing| Power not
wired, damaged fuse| Inspect power and wire, change fuse
Warranty
WARRANTY Hamoki Ltd warrants the original purchaser of every new product
(under normal and proper use and maintenance service as specified by Hamoki
Ltd and upon proper installation and start-up in accordance with the
instruction packet supplied with each unit) a one year parts warranty.
Hamoki Ltd’s obligation under this warranty is limited to a period of one (1)
year from the date of original installation.
WARRANTY CLAIMS:
All claims for parts must be made directly through the retailer in the first
instance. All claims raised with the retailer should include:
Your name:
Model number:
Your company:
Serial number of the product:
Address: Date of purchase:
Email: Proof of purchase :
Phone:
Information supporting the alleged defect.(A video/photo)
Photo of the dataplate.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>