BlueAnt X-3D 20 Watt Bluetooth Speaker User Manual
- June 14, 2024
- BlueAnt
Table of Contents
X-3D
20 Watt Bluetooth Speaker
User Manual
Welcome
You’ve just unlocked a world of awesome with your X3D purchase.
Please read through this manual to unleash the full magic of your speaker. Let
the fun begin!
Inside the box
The X3D is capable of very high volume output.
For Continuous Play, please use the supplied Fast Charger and Fast Charging
Cable for endless uninterrupted audio.
Get to know your X3D Speaker
Item | Button | Function |
---|---|---|
1 | Power Button – Press for 1.5 seconds to power on Press for 1.5 seconds to |
turn off
2| | Bluetooth Indicator
3| | Battery Indicator
4| | AUX in Jack 3.5mm
5| | USB-C Charge Port – USB-C to USB-C cable supplied
6|
+
| Volume Up – Click or press and hold
7| | Click to Play/Pause
Double Click to skip forward a track
Click to Answer/End a Call
Double Click or press and hold to reject a call
8| | Microphone
9| | Volume Down – Click or press and hold
10| | Press for 1.5 seconds to disconnect Bluetooth
Let’s Get Started
Charging the X3D
Please use the supplied USB-C to USB-C Fast charge cable and Fast charger to
charge the X3D.
A full charge will take around 2 hours. Please close the port cover after you
have charged the speaker.
WATERPROOF – The X3D features waterproof IP67 rating. The speaker is only
waterproof when the port cover is closed.
Power ON/OFF
- Press and hold the power button for 1.5 seconds to power the speaker ON or OFF.
Each time the speaker powers on, it will reset to 25% volume. After 10 minutes with no connection, the speaker will automatically power OFF to conserve battery.
MODES
A) Bluetooth Mode – Pairing the speaker to your phone or device
- Power ON the speaker and press button to go into Bluetooth pairing. The light indicator will flash.
- On your phone or device, look for “BlueAnt X3D” under the Bluetooth settings menu. Click on “BlueAnt X3D” on your phone.
- Once paired, the speaker will say “Connected” and the LED display will stop flashing. You are now ready to play some music!
B) Using the buttons for playing music
+ | Click or press and hold to increase volume |
---|---|
Click to Play/Pause |
Double click to skip forward a track
| Click or press and hold to decrease volume
Let’s Get Started cont’d…
C) Calls
| Click to answer an incoming call
---|---
| Click to end the active call
| Double click to reject an incoming call or press & hold
D) Disconnect
Press and hold the Bluetooth button for 1.5 seconds to disconnect the current Bluetooth connection. The speaker will prompt, “Disconnected”. Then other Bluetooth devices can find and pair with the speaker.
E) Duo Mode
Duo Mode Connection
The BlueAnt X3D can be paired to another X3D or an X3D Max in Duo Mode
- Press the power button on the PRIMARY speaker, to turn the speaker on.
- Then on the PRIMARY speaker, press and hold the Volume + & Volume – buttons for 1.5 seconds, until the speaker says, “Duo Mode Pairing”. Then release the button.
- Press the power button on the SECONDARY speaker, to turn the speaker on.
- Then on the SECONDARY speaker, press and hold the Volume + & Volume – buttons for 1.5 seconds until the speaker says, “Duo Mode Pairing”. Then release the button.
- Please wait until one speaker says, “Duo Mode Connected”. This may take up to 1 minute.
The speakers are now connected to each other
Let’s Get Started cont’d…
For Bluetooth pairing, search for “BlueAnt X3D” on your smartphone. If you
receive a call while in Duo Mode, the call will only come through the PRIMARY
speaker.
When in Duo Mode and you power off one speaker, BOTH speakers will power off.
When you power on the speakers, they need to be turned on individually.
When you power on the SECONDARY speaker, if it had previously been connected
in Duo mode, it will reconnect to the PRIMARY speaker.
Duo Mode Disconnection
To disconnect Duo Mode, press and hold the Volume + & Volume – buttons for 1.5
seconds, on the SECONDARY speaker until the speaker says, “Duo Mode
Disconnected”. The speaker will then say, “Duo mode Cleared”.
This means the SECONDARY speaker will no longer automatically reconnect to the
PRIMARY speaker when it powers on.
Assuming direct line of sight, you should be able to achieve a range of over
30 metres between the speakers. When used indooors, the range will be affected
by internal walls or obstacles between the speakers.
AUX In Mode
Use 3.5mm audio cable to connect the speaker to an audio source (PC, MP3/MP4,
mobile phone). When you plug the AUX cable into the speaker, it will
automatically change to AUX In Mode. When you unplug the AUX cable, the
speaker will change to Bluetooth mode. The speaker will play the music from
the audio source.
+ | Click or press and hold to increase volume |
---|---|
Click to mute/unmute play back | |
Click or press and hold to decrease volume |
SAFETY INFORMATION & WARRANTY TERMS
Important Safety Information
PLEASE READ THIS ENTIRE DOCUMENT CAREFULLY, BECAUSE IT CONTAINS
IMPORTANT INFORMATION ABOUT THE USE OF BLUEANT DEVICES
WARNING – PROTECT YOUR HEARING
BLUEANT DEVICES CAN REACH VOLUMES ABOVE 100 DECIBELS
ONLY CHARGE WHEN DEVICE IS CLEAN AND DRY
Care and Handling
Your BlueAnt Bluetooth device is a precision engineered instrument. To ensure
its ongoing performance, you should look after it as you would any quality
consumer electronic product, and use it in accordance with the instructions.
BlueAnt recommends that you
take the following precautions. Avoid leaving your device in direct sunlight.
- Do not leave your device, or use your device, in any area where the temperature may exceed 45 degrees Centigrade, such as inside a closed car on a hot day. Remember that on a hot day, the temperature inside a closed car may be significantly higher than the outside air temperature.
- Do not leave your device, or use your device, in any area where the temperature is likely to drop below 0 degrees Centigrade (32 degrees Fahrenheit).
- Do not leave your device, or use your device, in any area exposed to humidity, dust, soot, other foreign objects, smoke, or steam as this may cause your device to malfunction.
PROLONGED USE AT HIGH VOLUMES MAY AFFECT YOUR HEARING CAPACITY AND MAY RESULT IN NOISE INDUCED HEARING LOSS (NIHL). TURN OFF THE POWER TO YOUR DEVICE WHEN NOT IN USE.
- Do not use any household or industrial grade detergents or cleaners to clean your device. If your device becomes dirty or smeared, in most instances a wipe with a dry or slightly damp cloth should be sufficient to clean it.
- Before charging your BlueAnt device, make sure that the AC outlet, adaptor and cable are not damaged. If you notice any abnormalities, seek advice from a qualified professional.
- If travelling internationally, ensure that your BlueAnt wall or car power adapter is approved for use in the country where you plan to use it and that the adapter voltage is suited to the local power supply.
- Should a fault develop with your BlueAnt product, contact BlueAnt for advice on how to proceed. Do not attempt to repair or alter any BlueAnt product yourself.
THANK YOU FOR CHOOSING A BLUEANT PRODUCT
Register your BlueAnt product for warranty and new product updates at:
register.blueantwireless.com
Approved Accessories
The use of accessories not approved by BlueAnt, including but not limited
to batteries, antennas, wall adapters, car charger, ear gels and foam tips and
convertible covers, may cause your BlueAnt device to malfunction or in the
case of non approved electrical accessories may cause the device to exceed RF
energy exposure guidelines.
Electromagnetic Interference
Nearly every electronic device is susceptible to electromagnetic interference
(EMI) if inadequately shielded, electromagnetic configured for electromagnetic
compatibility. Similiar to a mobile phone, your BlueAnt device is a low power
transmitter/receiver and is covered by regulations pertaining to such devices.
Turn off your BlueAnt device in any facility where posted notices instruct you
to do so. These facilities may include hospitals or health care facilities
that may be using equipment that is sensitive to external RF energy.
- When instructed to do so, turn off your BlueAnt device when on board an aircraft. Any use of a mobile device must be in accordance with applicable laws, regulations and airline crew instructions.
- If you use any other personal medical device, consult the manufacturer of your device to determine if it is adequately shielded from RF energy. Your doctor or physician may be able to assist you in obtaining this information.
- If you are in doubt about whether your BlueAnt device can be safely turned on or used, please consult an authorised person in the location you want to use your BlueAnt device. If no authorised person is available or you remain uncertain, BlueAnt recommends that you turn off your Bluetooth device and any mobile phones unless they are required in an emergency situation.
Recycling Bluetooth Accessories
Do not dispose of Bluetooth accessories, such as chargers, speakers,
headphones or headsets with your household waste. In some countries or
regions, collection systems are set up to handle electrical and electronic
waste items, and may prohibit or restrict how such items are disposed of.
Check the laws and regulations for your areas to determine how to properly
dispose of such items.
BlueAnt Limited Global Warranty
This product is covered by BlueAnt’s limited global warranty for one (1) year
from the date of purchase by the first consumer purchaser of the product.
Please refer to
warranty.blueantwireless.com for full
terms and conditions.
For warranty and technical support, please email care@blueantwireless.com or head over to our website: www.blueantwireless.com
Australian Consumer Law
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure
and compensation for any other reasonably foreseeable loss or damage. You are
also entitled to have the goods repaired or replaced if goods fail to be of
acceptable quality and the failure does not amount to a major failure.
BlueAnt Wireless
Suite 6, 861 Doncaster Road
Doncaster, Vic, 3109 Australia
https://qrcodes.pro/T0naPc
REGISTER & SCAN
Register your BlueAnt product for
warranty and new product updates
by scanning the QR Code above
Visit support.blueantwireless.com
or email: care@blueantwireless.com
100% AUSTRALIAN
DESIGNED & OWNED
References
- BlueAnt Wireless
- Product Registration – BlueAnt Wireless
- Support – BlueAnt Wireless
- BlueAnt Wireless