HARVEST TEC 664 Automatic Preservative Applicator Installation Guide

HARVEST TEC 664 Automatic Preservative Applicator

Introduction

Thank you for purchasing a Harvest Tec Model 664 Hay Preservative Applicator. This 664 applicator system has been designed to be operated through an Apple iPad (not included) using the Hay App. As well as the option to plug directly into most tractors that have an ISOBUS Monitor. The 664 Applicator System offers these advantages by operating through an Apple iPad:

1. Large bright, clear, colorful display
2.  More durable and can be read in bright sunlight
3. Can be used for multiple other uses than just the applicator display
4. Option to tie-into the tractor ISOBUS system

This manual will take you through the steps for installing the update to the automatic applicator. If you are unsure about installing the system after consulting this manual, please contact your local authorized dealership for additional assistance. If you are in need of parts for the system please see the parts breakdown in the back of this manual and contact your local authorized dealer to order the parts. This applicator is designed to apply Harvest Tec buffered propionic acid.
Right and Left sides are determined by facing in the direction of forward travel.

System Requirements
Made for iPad® running the current iOS operating system
or one version previous required for iPad option
iPad is a trademark of Apple Inc., registered in the U.S. and other countries.
600 Series Applicators with serial number before DCP27000 will require the DCP to be sent to Harvest Tec for a required update in order to use the iPad Integration Module (030-6672C).
*Hay App version must be at least 2.5.18 (or higher) to operate with the iPad Integration Module
If choosing to operate the unit though the ISOBUS monitor, pn 006-6670A will need to be ordered through your local equipment dealer. 2018 Krone balers (and beyond) Serial Number 976909 will need pn 006-6650VAK.
Tools Needed:

• Standard wrench set
• Side cutter

Installation of Dual Channel Processor (DCP)

The Dual Channel Processor (DCP) has the same bolt pattern as the Precision Information Processor (PIP) you will be removing. The location of the main controller does not change so use the same holes and install the new Dual Channel Processor (DCP) in the same location with two 5/16” x 1” bolts, two 5/16” x 1-1/4” bolts, locks, fender washers and hex nuts. Mount the DCP cover over the top of the DCP and secure with the hardware using the 5/16” x 1-1/4” bolts on the top with the DCP shield.
DCP or PIP Location
AGCO Balers

Installation of Main Power / Communication Harness

Route cords 006-6650LS2 along this path or similar inside of the baler. Keep cords away from moving parts and hydraulic hoses. Secure with existing cable clamps or use cable ties. When all connections are made to DCP secure wires.

Connecting the optional ISOBUS plug to the tractor
Attach the optional ISOBUS connector (006-6670A) to the end of the communication harness (006-6650TM).
Connect the orange wires and attach the plug to the tractor’s ISOBUS port.
Then connect the ISOBUS connector to the ISOBUS plug on the tractor.

Installation of iPad Integration Control

Locate a safe location in the cab of the tractor to place the iPad Integration Control (030-6672C). Recommended location is securely fastened out of the operators way in a location that is close enough to reach with the iPad cord.
Connect the Power / Communication harness (006-6650TM(E)) to the bottom of the receiver.
To operate the applicator, plug the iPad cord into the communication port indicated by:

iPad Integration Control Light Signals

Green Slow Blink – Power supplied to the applicator system and the unit is going through its startup process. This will take approximately 25-35 seconds.
Green Double Blink – Indicating the iPad module recognizes the iPad but the app is not open or connected. Green Solid Light – Module is connected to the app and is ready to operate.
Recommended to use the USB cable included with the applicator kit (006-6672USBC)

Bluetooth Receiver Lights

Pre-2020 applcaitors equipped with Bluetooth receivers (030-6672B) are now equipped with lights to indicate both power and Hay App connection on the Apple iPad. Clean light regularly
Blinking Lights – System is waiting for the processor to connect, which could take up to 35 seconds.
Red Light – The Bluetooth receiver has power
Green Light – The Bluetooth receiver is connected to the Hay App.
600 Series Applicators with serial number before DCP27000 will require the DCP to be sent to Harvest Tec for a required update in order to use the iPad Integration Module (030-6672C).
Hay App version must be at least 2.5.18 (or higher) to operate with the iPad Integration Module
*Made for Apple iPad badge
Use of the Made for Apple iPad badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
Please note that the use of this accessory with an Apple product may affect wireless performance.

Wiring Diagram

1. The Baler Power/Communication Harness (006-6650LS2) will attach to the open port of the Tractor Harness (006-6650TM) and run back to the Dual Channel Processor (006-6671LS). Connect the large plug of the Baler Power/Communication Harness (006-6650LS) to the bottom (shorter side) of the DCP.
2. Install green terminator (006-5650Z) to the port labeled Modular Port on the Pump Controller (006-5672).
3. Attach moisture and bale rate harness 006-7303H (Claas & Krone kits 006-7303HX) as well as the end of bale harness (006-7400) to the DCP (006-6671LS).
4. Attach the Pump Control Harness (006-5650FM) between the Pump Controller (006-5672) and the DCP (006-6671LS).
5. Connect the orange wires and attach the plug to the tractor’s ISOBUS port.
6. If using the optional ISOBUS connector (006-6670A) connect the end to the Communication Harness (006-6650TM) in place of the iPad Integration Control (030-6672C) shown below.
7. Connect the orange keyed power wires (006-5650K) and attach the plug to the tractor’s ISOBUS port.

Claas 3200-3400 balers will have star wheel assembly 030-4642 for mounting on side of bale chamber

Pin Outs

Power/Comm Harness 006-6650TM at Hitch

• Pin 1 Red +12V Power to TSD
• Pin 2 Red +12V Power to DCP
• Pin 3 Orange Keyed Power
• Pin 4 Gray Shield
• Pin 5 Green HT Can Low
• Pin 6 Yellow HT Can Hi
• Pin 7 Orange Can1 Hi
• Pin 8 Black Ground from TSD
• Pin 9 Black Ground from DCP
• Pin 10 Blue Can1 Low

Power/Comm Harness 006-6650LS2 at Hitch

• Pin 1 Red +12V Power to TSD
• Pin 2 Red +12V Power to DCP
• Pin 3 Orange Keyed Power
• Pin 4 Gray Shield
• Pin 5 Green HT Can Low
• Pin 6 Yellow HT Can Hi
• Pin 7 Orange Can1 Hi
• Pin 8 Black Ground from TSD
• Pin 9 Black Ground from DCP
• Pin 10 Blue Can1 Low

iPad Integration Control / BLE on Harness 006-6650TM

• Pin 1 Red +12V Power from DCP
• Pin 2 Black Ground from TSD
• Pin 3 Yellow HT Can Low
• Pin 4 Gray Shield
• Pin 5 Green HT Can Hi
• Pin 6 Orange Can1 Hi
• Pin 7 Blue Can1 Low

ISOBUS Plug Baler Side

• Pin 1 N/A
• Pin 2 N/A
• Pin 3 120 OHM with Pin 5
• Pin 4 N/A
• Pin 5 120 OHM with Pin 3
• Pin 6 Orange Can1 Hi
• Pin 7 Blue Can1 Low

ISOBUS Plug Tractor Side

• Pin 1 N/A
• Pin 2 N/A
• Pin 3 +12V Keyed Tractor Power
• Pin 4 N/A Pin 5 Pin 6 N/A
• Pin 7 N/A
• Pin 8 Orange Can1 Hi Pin 9 Blue Can1 Low

Main Power Connector on DCP

• Pin 1 Red +12V Power from tractor
• Pin 2 Black Ground from tractor
• Pin 3 Orange Keyed power

Star Wheel and Bale Rate Sensor connector on DCP

• Pin 1 Blue +12V Power
• Pin 2 Orange Ground
• Pin 3 Black Signal for sensor 1
• Pin 4 White Signal for sensor 2
• Pin 5 N/A
• Pin 6 N/A
• Pin 7 N/A
• Pin 8 Violet Star wheel input 1
• Pin 9 Brown Star wheel input 2

End of Bale sensor on DCP

• Pin 1 Brown Sensor Power
• Pin 2 Blue Sensor Ground
• Pin 3 N/A
• Pin 4 Black Signal from Sensor

Pump Connection Colors

• Pin 1 Black with Orange Stripe Pump 1 Ground
• Pin 2 Black with Green Stripe Pump 2 Ground
• Pin 3 Black with Yellow Stripe Pump 3 Ground
• Pin 4 N/A
• Pin 5 Orange with Black Stripe Pump 1 Positive
• Pin 6 Green with Black Stripe Pump 2 Positive
• Pin 7 Yellow with Black Stripe Pump 3 Positive

Parts Breakdown

(Converting a 500 Series to a 600 Series)

Ref : Description Part :  Number : Qty

1. Key Switch Wire-orange 006-5650K 1
2. DCP Main Control LS 600 Auto 001-6671LS2 1
3. Terminating Resistor 500 Series-green 006-5650Z 1
4. Dust Plug (only one included)-yellow 006-5651Plugs 1
5. DCP Baler Harness 30 ft 006-6650LS2 1
6. DCP Tractor Harness 006-6650TM 1
7. iPad Integration Control 030-6672C 1
   NP Optional ISOBUS Adapter Plug (not included) 006-6670A 1
   NP USB Cord 006-6672USBC 1

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>