TKH SECURITY HSG05 Outdoor Fixed Housing Installation Guide

TKH SECURITY HSG05 Outdoor Fixed Housing

Product Information

The HSG05 camera enclosure is a durable and weather-resistant housing designed for outdoor use. It is made of die-cast aluminum alloy with white epoxy powder coating and has an IP67 rating, making it dust-tight and waterproof. The enclosure includes a window heater, blower, and camera with a maximum output power budget of 30W. It has a power input of 90-260 Vac and can be powered through PoE or 24V AC. The dimensions of the enclosure are 502.8 (L) x 170 (W) x 185.5 (H) mm, and it weighs 2.2kg (4.84 lb).

Specifications

• Model Number: HSG05
• Power Input: 90-260 Vac
• Max. Output power budget: 30W
• Power Consumption: Window heater: 10W; Blower: 2W; Camera: 6 ~ 8W
• Environmental Operation Temp.
• Blower Control
• Protection Level: IP67, IK10
• Construction: Die-cast Aluminum Alloy
• Coating: White epoxy powder coating
• Dimensions: 502.8 (L) x 170 (W) x 185.5 (H) mm
• Net Weight: 2.2kg (4.84 lb)

Mounting Configuration & Dimensions

The HSG05 camera enclosure swivels and can be mounted in different positions and directions. The usable area for mounting is 105 mm (4.13 in) on the top, 400 mm (15.75 in) on the side, and 255 mm (10.03 in) on the bottom. The dimensions with the IR unit and wiper are 502.8 mm (19.80 in) in length, 241.7 mm (9.51 in) in width, and 135 mm (5.32 in) in height.

Component Description

The HSG05 camera enclosure includes the following components:

• Ventilation fan
• Window frame heater coil VAIR module
• AC/DC or PoE Power distribution board
• Camera Mounting Platform
• M16 1/2 Waterproof cable glands

Product Usage Instructions

Before using the HSG05 camera enclosure, please read and follow the instructions in the installation guide carefully.

Unpacking

Unpack the camera enclosure carefully to avoid damaging any electronic components. If an item appears damaged in shipment, place it properly in its carton and notify the shipper.

Installation

Only a qualified electrician is allowed to make electrical connections. A readily accessible disconnect device in the building installation wiring should be incorporated. Prepare power wires, a ground wire, and a CAT5e Ethernet cable. Pass them through power wires & DI/DO wires, a combo cable from IR illuminator (if applied). Note that some cables are connected when shipped. You do not need to connect heater, blower, and the front IR power wires.

Environmental Conditions

If you plan to install this camera enclosure into a tropical, sea coastal, or an environment where salt water or corrosive industrial waste water/moist are present, please seal each stainless steel screw and fitting with a silicon grease compound. This will help prevent electrolysis from occurring and extend the lifespan of the camera and housing.

UNPACKING:
Unpack carefully. Electronic components can be damaged if improperly handled or dropped. If an item appears damaged in shipment, place it properly in its carton and notify the shipper.

IMPORTANT!:

1. Read and follow Instructions: All operating and user instructions should be read and followed before the unit is to be operated.
2. Electrical Connections: Only a qualified electrician is allowed to make electrical connections.

Specification

185.5 (H) mm
Net Weight| 2,2kg (4.84 lb)

If you plan to install this camera enclosure into a tropical, sea coastal, or an environment where salt water or corrosive industrial waste water/moist are present, please seal each stainless steel screws and fittings with a silicon grease compounds. This will help prevent electrolysis to occur and extend the life span of the camera and housing.

IMPORTANT:

1. Disconnect devices: A readily accessible disconnect device in the building installation wiring should be incorporated.
2. Electrical Connection: Only a qualified electrician is allowed to make electrical connections.

Mounting Configuration & Dimensions

Swivel Positions and Directions

Dimensions with the IR unit and wiper

Component Description

Installation Suggestions

WARNING:

• When install a housing with an IR illuminator:
  Please avoid eye exposure or apply appropriate protection, such as wearing a pair of Infrared protection glasses, when working with the product. Always use camera live view to observe IR lighting effects.

• Must power off the camera enclosure before installing the IR LED. The camera housing will be damaged if the IR LED is installed when the camera housing is powered. ‼

Installation

1. Prepare power wires, a ground wire, and a CAT5e Ethernet cable. Pass them through the M16 waterproof connectors and its waterproof components.
   Note that some cables are connected when shipped. You do not need to connect heater, blower, and the front IR powere wires.
   You may need to remove the RJ45 connector, and use a crimping tool to connect the Ethernet wires to an RJ45 connector inside the enclosure. Use an Ethernet cable of the width of 5 ~ 6.5mm.

2. When done, tighten up and install the waterproof connectors.

3. Assemble the camera components, e.g., the CS ring and lens module. Secure the mounting plate to the bottom of the camera (the label side) using the included screw.
   

4. Adjust the camera’s position so that the lens module can flush align with the tempered glass. Secure the camera using the screws and washers to the bottom of the housing.
   

5. Connect 24V power source to the power input terminal (already pre-assembled via built-in PSU with Line Voltage input). Connect power wires from the DC 12V output to the camera.
   Below is the distribution board drawing power from 24V AC.

Below is the pinouts for the DI/DO terminal block:

Facing the rear side of the housing, from left to right:

related to IR cut filter.

7. If using the HSG04-Wall wall-mount bracket, secure the intersection bracket to the bottom oft he housing by driving two screws.

Below are the mounting hole dimensions for the mounting brackets. Chances are you may need to plan for the locations of the brackets.

8. Install the housing to the wall-mount bracket by aiming and pressing the spring mortise, and hook the bracket onto the groove in the spring mortise.
   

9. Adjust zoom and focus and open a web console with the camera to tune for the best image. When zoom and focus is done, Close the top cover and fasten the top cover screws.
   The housing can also be installed using the pole-mount or corner-mount options along with a power box (PB-024-1AC, PB-024-2AC), outdoor PoE switch, or junction box.
   Use the included M10 hex socket screws to secure the power box to a pole-mount or corner mount bracket.
   The mounting hole definition is illustrated below. The same mounting hole pattern apply to all pole- mount and corner- mount brackets.
   If a power box or outdoor PoE switch is applied, Use the following mounting positions for the camera housings (via BK-100 and BK-101).
   

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>