GAGGENAU CI282602 Flex Induction Cooktop Installation Guide

GAGGENAU CI282602 Flex Induction Cooktop

Gaggenau Cooktop – Product Information

The Gaggenau Cooktop is a high-quality kitchen appliance that provides efficient and safe cooking experience. The cooktop is designed to be installed in a flush-mounted 36 cooktops and comes with various safety features to reduce the risk of electrical shock, fire, and injury to persons.

Safety Instructions

Before using the cooktop, it is essential to carefully read and follow all safety instructions provided in the user manual. The appliance must be installed by a qualified installer, and the installation instructions should be left with the unit for the owner. It is essential to turn off the power at the service panel before installing the cooktop. Improper installation, service, or maintenance can cause injury or property damage. We strongly recommend installing a ventilation system with this appliance to reduce the risk of any damage.

Product Usage Instructions

Here are some essential instructions for using the Gaggenau Cooktop:

1. Before using the cooktop, examine it for any transport damage. If there is any damage, do not plug it in and contact the manufacturer immediately.
2. Remove all tape and packaging before using the appliance. Dispose of packaging in an environmentally responsible manner.
3. Verify that cabinets above the cooktop are a maximum of 13 (330 mm) deep.
4. When using the cooktop, use caution when reaching behind or under appliance as hidden surfaces may have sharp edges.
5. Do not repair, replace or remove any part of the appliance unless specifically recommended in the manuals.

Following these instructions will help you use your Gaggenau Cooktop safely and efficiently. For further guidance, refer to the user manual.

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS Read all instructions carefully before use. These precau-tions will reduce the risk of electrical shock, fire and injuryto persons. When using kitchen appliances, basic safetyprecautions must be followed including those in the follow-ing pages.

Safety definitions
Here you can find explanations of the safety signal wordsused in this manual.

WARNING
This indicates that death or serious injuries may occur asa result of non- observance of this warning.

CAUTION
This indicates that minor or moderate injuries may occuras a result of non- observance of this warning.

NOTICE:
This indicates that damage to the appliance or propertymay occur as a result of non-compliance with this advi-sory.

Note
This alerts you to important information and/or tips.

General information

• Read this manual carefully.
• Keep the instructions, the appliance pass and the prod-uct information safe for future reference or for the nextowner.
• Do not connect the appliance if it has been damaged intransit.

General safety instructions

• IMPORTANT : THE APPLIANCE MUST BE INSTALLEDBY A QUALIFIED INSTALLER.
• IMPORTANT : SAVE THESE INSTRUCTIONS FOR THELOCAL ELECTRICAL INSPECTOR’S USE.
• INSTALLER : LEAVE THESE INSTALLATION INSTRUC-TIONS WITH THE UNIT FOR THE OWNER.
• OWNER : PLEASE RETAIN THESE INSTRUCTIONSFOR FUTURE REFERENCE.
• Examine the appliance after unpacking it. In the event oftransport damage, do not plug it in.

WARNING
If the information in this manual is not followed exactly, fireor shock may result causing property damage or personalinjury. Do not repair, replace or remove any part of the applianceunless specifically recommended in the manuals. Im-proper installation, service or maintenance can cause in-jury or property damage

• Refer to this manual for guidance.
• All other servicing should be done by an authorized ser-vice provider

When installing a cooktop over a single oven, be sure tofollow the instructions in both the oven’s and the cooktop’sinstallation manuals. DO NOT install any refrigerators, dishwashers, ovens(without ventilation), or washing machines below the cook-top. Refer to the Approved Combination Matrix. Never modify or alter the construction of the appliance. The appliance should only be used if installed by a quali-fied technician in accordance with these installation in-structions. The manufacturer is not responsible for anydamage resulting from incorrect installation. To eliminate the risk of burns or fire by reaching overheated surface units, cabinet storage space located abovethe surface units should be avoided.

• If cabinet storage is to be provided, the risk can be re-duced by installing a hood that projects horizontally aminimum of 5″ (127 mm) beyond the bottom of the cabi-net.
• Verify that cabinets above the cooktop are a maximumof 13″ (330 mm) deep.

NOTICE:
We strongly recommend the installation of a ventilationsystem with this appliance.

WARNING
Remove all tape and packaging before using the appli-ance.

• Destroy the packaging after unpacking the appliance.
• Dispose of packaging in an environmentally responsiblemanner.
• Never allow children to play with packaging material.

Appliance handling safety

WARNING
Hidden surfaces may have sharp edges. Use caution when reaching behind or under appliance.

Safety codes and standards
This appliance complies with the latest version of one or more of the following standards:

• UL 858 – Household Electric Ranges
• CAN/CSA-E60335-2-6, The Standard for the Safety of

Household and similar electrical appliances. It is the responsibility of the owner and the installer to determine if additional requirements and/or standards apply to specific installations.

Electrical safety

• Installer – show the owner the location of the circuit breaker or fuse. Mark it for easy reference.
• If required by the National Electrical Code (or Canadian Electrical Code), this appliance must be installed on a separate branch circuit.
• Local codes vary. The installer is responsible for ensuring that the installation, connections, and grounding comply with all applicable codes. The manufacturer is not responsible for any issues associated with the improper installation of this product.
• The circuit breaker should have a contact separation of at least 3 mm on all poles.
• Refer to the rating plate for more information. → “Rating plate location”, Page 11
• This appliance also incorporates an internal earth connection for functional purposes only.

WARNING
Before installing, turn power OFF at the service panel.

• Lock service panel to prevent power from being turned ON accidentally.
• IMPROPER GROUNDING CAN RESULT IN A RISK OF ELECTRIC SHOCK
• Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded.
• DO NOT USE AN EXTENSION CORD. GROUNDING INSTRUCTIONS
• This appliance must be grounded.
• Grounding reduces the risk of electric shock by providing a safe pathway for electric current in the event of a short circuit.
• Be sure your appliance is properly installed and grounded by a qualified technician.
• Installation, electrical connections and grounding must comply with all applicable codes.

State of California Proposition 65 Warnings
This product may contain a chemical known to the State of California, which can cause cancer or reproductive harm. Therefore, the packaging of your product may bear the following label as required by California

STATE OF CALIFORNIA PROPOSITION 65 WARNING:
Cancer and Reproductive Harm – www.P65Warnings.ca.gov

Before you begin

Before you begin Read these instructions before you begin to install your appliance

Parts included
After unpacking all the parts, check for any damage in transit and for completeness of delivery.

Tools and parts needed
Prepare these tools and accessories before you start to install your appliance.

• Pencil
• Measuring tape
• Cross head screwdriver
• Drill with bit 1/4″ (6 mm)
• Jigsaw

Note : Additional materials may be necessary for installation in solid surface countertops. Contact the countertop manufacturer

Cabinet requirements
Ensure that the cabinetry at the installation location meets the requirements for a safe installation.

• The distance from the top of the cooktop to the bottom of cabinets above must be a minimum of A=30″ (762 mm).
• This distance can be reduced to A=24″ (610 mm) when the bottom of the wood or metal cabinet is protected by not less than ¼” (6.35 mm) flame-retardant billboard covered with not less than no. 28 gauge sheet metal, 0.015″ (0.4 mm) stainless steel, 0.024″ (0.6 mm) aluminum or 0.020″ (0.5 mm) copper.
• Verify that unprotected cabinets above the cooktop are a maximum of B=13″ (330 mm) deep.

Installation in combination with other products
Both products must be installed according to their specific product installation instructions.

Installing a cooktop over ovens and microwaves:
Only certain models may be installed over an oven or a microwave. Verify the Approved Combination Guide supplied with these instructions for approved installation combinations. Both products will have a label stating Approved Combination Guide.

Installing a range hood or a microwave hood above the cooktop:
Follow the range hood or microwave hood installation instructions for dimensional clearance above the cooktop surface.

Countertop requirements
Ensure that the countertop into which the cooktop is to be installed meets these requirements for a safe installation.

WARNING
To reduce the risk of ignition of surrounding combustible materials, install at least 2″ (51 mm) from both sidewalls and the rear wall.

• The countertop must be level and horizontal.
• The stability of the countertop must be maintained after the cut-out has been made.
• Solid surface countertops often require special installations. For example, heat-reflective tape and rounded corners may be necessary.
• Contact the countertop manufacturer for instructions specific to your countertop.

Prepare installation space

Prepare installation spaceCreate the cutout in the countertop according to the instructions.

General countertop requirements:

• The angle of the cut surface to the countertop must be 90°.
• With multi-layered countertops, secure strips laterally in the cutout if necessary.
• After creating the cutout, remove all shavings.
• Seal the cut surfaces in a heat- and water-resistant manner.
• Observe the minimum distance between device underside and cabinet surfaces of ⅜” (10 mm).
• The countertop into which the cooktop is installed must be heat-resistant up to 140° F (90 °C).
• The countertop into which the cooktop is installed must be at least ¹³/₁₆” (20 mm) thick
• If the thickness of the countertop into which the cooktop is installed does not comply with the specifications, reinforce the worktop using a fire- and water-resistant material until it reaches the minimum thickness. Otherwise, sufficient stability cannot be assured.
• The countertop into which the cooktop is installed should withstand loads of approx. 133 lbs (60 kg).
• Confirm the cooktop is level only after it has been installed.

Flush mounting
The cooktop can be mounted flush into the countertop.

Notes

• Any cutout work on the countertop must be performed in a workshop according to the installation diagram.
• The cutout edge is visible on the surface after installation. Ensure that the cutout is made cleanly and precisely.
• Clean and degrease the cutout edges with a suitable cleaning agent; follow the silicone manufacturer’s processing instructions.

Countertop material guide for flush mounting
Refer to the following chart to see if flush mounting is possible. All countertop materials must be temperature- and water-resistant.

Cutout dimensions for flush mounted 30″ cooktops
Refer to these measurements for the models stated here. CI 282 602

Cutout dimensions for flush mounted 36″ cooktops
Refer to these measurements for the models stated here. CI 292 602

Notes

• A minimum clearance between the rear of the cabinet and the kitchen wall, and between the surface of the countertop and the upper area of the drawer.
• An opening at the top to the rear of the cabinet.
• If the minimum clearance of 13/16″ (20 mm) is not provided at the rear of the cabinet, you must create an opening on the underside
• If the inside of the cabinet is no wider than 29 ½” (750 mm), make cutouts in the side panels
• If the appliance is installed in an island unit or another installation that is not described here, you must ensure that the cooktop is sufficiently ventilated.

Installation procedure

Installation procedureFollow these instructions to install the cooktop into the countertop.

CAUTION
Sharp edges. Use protective gloves when installing the appliance.

CAUTION
The appliance is heavy. It is recommended that two people install this appliance.

Installing the heat shield
For safety reasons, the heat shield must be properly installed when closed cabinets are used. This prevents components from overheating as a result of the recirculation of hot air from the cooktop. The heat shield is the same width as the cooktop.

CAUTION
Sharp edges. Use protective gloves when installing the heat shield.

Requirement : You have unpacked the cooktop.

• For shipping, the heat shield is screwed to the bottom of the cooktop. Unscrew the fastening screw on heat shield
• The heat shield will be able to rotate freely.

Attaching the sealing tape for flush installation Attach the adhesive sealing tape around the edges of the countertop cutout.

Note : Do not apply the sealing tape to the cooktop.

Securing the cooktop to the countertop
The cooktop must be secured from below using the hold-down brackets provided, so it does not slip.

1. Place the cooktop face down on a soft underground.
2. Attach the hold-down brackets to the underside of the cooktop with the provided short screws . Do not tighten the screws
3. Rotate the hold-down brackets so that the appliance can be placed in the cutout.
4. CAUTION Do not let the cooktop drop into place.
5. Make sure that the cooktop is supported along the edges when carefully placing it into the cutout. Turn the cooktop over and place it carefully into the countertop cutout.
6. Insert the clamping screws into the hold-down bracket and secure the cooktop to the countertop . Protect delicate countertops by placing a wooden disk underneath.
7. Tighten the hold-down bracket screws on the cooktop underside.
8. Only for flush mount installation:
9. Carry out the installation test before carrying out this step.
10. Grout the surrounding gap with a suitable temperature- resistant silicone adhesive.
11. Smooth the joint seal with a smoothing agent recommended by the manufacturer. Follow the processing instructions for the silicone glue.
12. Let the silicone glue dry completely for at least 24 hours, depending on the room temperature before switching on the appliance.

Electrical connection

Electrical connectionRead these instructions to safely connect your appliance to the electrical supply

Electrical requirements
Ensure that the following general requirements are met.

• You can find the rating plate with the electrical specifications on the underside of the appliance. → “Rating plate location”, Page 11
• The junction box must be located within 3 feet of the cooktop connection. It should be easily accessible for service purposes.

1. A max. 2¾” (69 mm) + fitting/conduit 1″ (25 mm)
2. B min. 1″ (25 mm) air clearance
3. C approx. 12″ (300 mm)
4. D junction box
5. E flexible conduit approx. 3 ft. (900 mm)

Power supply
All models must be connected with the included 39″ (1 m) flexible conduit.

Models| 240 V AC, 3-wire, 60 Hz system: cir- cuit breaker| 208 V AC, 3-wire, 60 Hz system: cir- cuit breaker
---|---|---
CI 482 602| 30 A| 30 A
CI 492 602| 50 A| 50 A

Connecting electrical supply

WARNING
Before installing, turn power OFF at the service panel. Lock service panel to prevent power from being turned ON accidentally.

Note: If the cooktop is installed and connected as specified here, it will be grounded in compliance with the National Electrical Code.

1. Install a suitable junction box (not furnished). The branch-circuit breakers ampacity, the wire sizes and the connections must conform to the requirements of the National Electrical Code or Canadian Electrical Code and all local codes and ordinances.

2. Attach the flexible conduit to the junction box

3. Connect the lead wires to the junction box supply wires in proper phase

4. Red wires

5. UL listed wire connectors

6. Green (or bare) ground wire (from appliance)

7. Cable from home power supply

8. Black wires

9. Junction box

10. Flexible conduit from appliance

11. Black wires of cooktop to black house wire

12. Red wires of cooktop to red house wire

13. Green or bare to ground

Checking the installation

Checking the installationCheck if your unit is working properly after you have completed the installation steps.

WARNING
Before you turn on power supply, make sure all controls are in the OFF position.

1. Remove everything from the cooktop surface including stickers.
2. Clean the cooktop surface with cooktop cleaning cream.
3. Switch on the circuit breaker.
4. Verify that all cooking zones function properly

Removing the appliance

1. Disconnect the appliance from the power supply.
2. For flush-mounted appliances, remove the silicone joint.
3. NOTICE : Do not lever the appliance out from above at the frame. Push out the appliance from below.

Customer Service

Customer ServiceIf you have any questions on use, are unable to eliminate an issue in the appliance yourself, or the appliance needs to be repaired, please contact our Customer Service. With any warranty repair, we will make sure your appliance is repaired by an authorized service provider using genuine replacement parts. We use only genuine replacement parts for all repairs. Detailed information on the warranty period and terms of warranty can be found in the Statement of Limited Product Warranty, from your retailer, or on our website. If you contact the Customer Service, you will need the model number (E-Nr.) and the production number (FD) of your appliance.

USA:
1-877-442-4436

• www.gaggenau.com
• www.gaggenau.com/us/appliances/eshop

CA:

• 1-877-442-4436
• www.gaggenau.com
• www.gaggenau.ca

For assistance with connecting to Home Connect™, you can also view instructions here:
www.home-connect.com/us/en/help-support/set-up

Model number (E-Nr.) and production number (FD)
You can find the model number (E-Nr.) and the production number (FD) on the appliance’s rating plate. The model number (E-Nr.) can also be found on the glass ceramic. You can also display the customer service index (KI) and the production number (FD) in the Basic settings. Making a note of your appliance’s details and the Customer Service telephone number will enable you to find them again quickly.

Rating plate location
You can find the rating plate of your appliance:

• on the underside of the appliance
• in the appliance pass
• You can also check the Customer Service Index (CSI) and the FD number in the basic settings

A Rating plate

BSH Home Appliances Corporation 1901 Main Street, Suite 600 Irvine, CA 92614 USA

www.gaggenau.com 1-877-442-4436 © 2021 BSH Home Appliances Corporation

References

• Select your region | Gaggenau
• Help & Support | Home Connect

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>