casselin CBINPP100 Bin Passage User Manual

casselin CBINPP100 Bin Passage

Product Information

Bin Pass-Plat
The Bin Pass-Plat is professional equipment used for passing dishes between the kitchen and the dining area. It comes in four different models: CBINPP100, CBINPP120, CBINPP150, and CBINPP180. The device has a power range of 2000W to 2800W with a voltage of 230V and operates at 50-60 Hz frequency. The device dimensions vary according to the model and are designed to fit in standard kitchen spaces. The device also comes with a guarantee for proper functioning.

Safety Instructions

Users must follow safety instructions for the safe and proper use of the device. The user manual contains detailed safety instructions and technical knowledge of the device. It is essential to read and follow these instructions to avoid material damage and bodily injury.

• WARNING: This symbol means that there is a danger that could result in injury. Concentration and caution are imperative in operating this device.
• ELECTRICAL HAZARD: This means that there is a danger associated with an electric current. Failure to follow the instructions can result in the risk of injury and death.
• WARNING: This symbol is used to indicate that failure to comply with the instructions may result in a breakdown or destruction of the device.
• REMARK: This symbol indicates good practices and advice that must be followed for the efficient use of the device.

PRESENTATION

Information
This user guide serves as information for all its users. It describes the installation and handling of the device. The safety instructions and technical knowledge of the device are detailed in this manual. They are essential conditions for the proper use of professional equipment. Each user must scrupulously follow all the instructions for use. These instructions for use must be kept next to the product for proper use and access to the instructions at all times for each user.

Description of symbols
Information, advice on use and safety instructions are represented by symbols. It is essential to follow these instructions in order to avoid material damage and bodily injury.

WARNING
This symbol means that there is a danger that could result in injury. Concentration and caution are imperative in operating this device.

ELECTRICAL HAZARD
This means that there is a danger associated with electric current. Failure to follow the instructions can result in the risk of injury and death.

WARNING
This symbol is used to indicate that failure to comply with the instructions may result in a breakdown or destruction of the device.

REMARK
This symbol indicates good practices and advice that must be followed for the efficient use of the device.

REMARK
It is essential to read these operating instructions before commissioning the device. We do not accept any liability for damage and breakdowns resulting from failure to observe the operating instructions. Casselin reserves the right to make any technical, informative, and marketing changes to our product without prior notice.

Rights’author
The operating instructions are protected by copyright law. Reproductions of all types and in all forms – even partial – as well as the use and/or transmission of its content are not permitted without our authorization. Any violation of these provisions gives rise to the right to damages. The other rights remain reserved.

Declaration of conformity
The device corresponds to the current standards and directives of the European Union. We confirm this in the CE declaration of conformity.

Guarantee
The instructions given in these operating instructions have been drawn up taking into account the regulations in force, current technical development, and our knowledge, and experience. All translations have been prepared with professionalism. However, we accept no responsibility for any translation error. The attached French version is authentic.

SAFETY

The safety instructions serve to prevent dangers. They are mentioned in the individual chapters and are characterized by symbols. Their observance guarantees optimal protection against risks and allows an ideal operation of the device. Safety instructions must be available and legible on the devices.

Principles
Safety instructions are established to prevent errors, dangerous uses, and breakdowns. Therefore, the device must not be transformed or used for improper use. The device is designed according to technical rules currently developed. This notice must be kept. The appliance must be used on premises provided for this purpose and only by a responsible person who knows the operation of the appliance.

Intended use
The functioning of the device and the safety of use are only guaranteed in the event of normal and correct use of the device. Assembly and technical interventions must be carried out by professionals.

WARNING
Any other use is considered improper. Any accusation related to improper use of the device is not admissible and will lapse. Correct use corresponds to the use described in these operating instructions. Correct use corresponds to compliance with the rules of safety, hygiene, cleaning and maintenance.

Safety instructions for the use of the device
The indications relating to occupational safety refer to the European Union ordinances valid at the time of manufacture of the device. For commercial use of the device, the operator undertakes, throughout its use, to note the compliance of the measures cited in terms of work safety with the current state of the arsenal of advice and to comply with the new regulations.

For countries outside the EU, the laws and provisions of the country must be observed. All environmental protection provisions must also be observed.

WARNING
The device must be handled by people with sufficient physical and intellectual resources. People with limited physical and intellectual means must be supervised to use this device. Use prohibited for children and minors (exceptions made within a legal framework provided for by law) If the device is used by a third person, the user manual must be available before any use. All new users must have read the instructions for use.

The device must only be used in rooms provided for this purpose.

TRANSPORT, PACKAGING, AND STORAGE

Inspection after transport
Checking for damage and the completeness of the device must be carried out upon receipt of the package. In the event of identification of damage due to transport, refuse or accept the delivered product only with reservations *. A complaint detailing the defects observed must then be made. The collection of damages is only possible in the event of a complaint formulated within the prescribed time limits, ie 24-48 hours at most.

• written on the carrier’s delivery papers or digital.

packaging
The packaging of the device must be kept in case of moving, or for a return to the after-sales service. The inner and outer packaging must be completely removed before using the device. The standards in force in your country concerning environmental protection must be observed before destroying the packaging.

Storage

WARNING
The device can be kept in stock, but only in its original, closed packaging. Storage can be carried out in accordance with these conditions:

• Storage in a dry and non-humid place
• Sheltered from the sun
• Control of the stock greater than 2 months (general condition of the device and all the elements constituting it)
• No material shaking
• Storage in a closed room and not outside.

EQUIPMENT CHARACTERISTICS

Subject to change

Installation and Use

Before installing and using the Bin Pass-Plat, it is essential to follow safety instructions to avoid accidents, material damage, or bodily injuries.

1. Unpack the device and check for any damage caused during transport.
2. Store the device in a dry and cool place to prevent any damage to the device’s electrical components.
3. Connect the device to a power source that meets the voltage and frequency requirements mentioned in the user manual. Ensure that the electrical installation is carried out by a qualified electrician.
4. Place the device in a stable and horizontal position on a flat surface.
5. Turn on the device and let it heat up for a few minutes before use.
6. Place the dishes or trays to be passed through the opening, and they will automatically pass to the other side.
7. After use, turn off the device and clean it according to the instructions provided in the user manual.

Safety instructions

ELECTRICAL HAZARD
Danger from electric current!

• No contact with heat sources should take place with the power cord.
• Cord should not hang over edge of table or counter.
• Do not pour water into an appliance that is in operation or that is still hot.
• The device must be properly connected and comply with the regulations in force.

WARNING
In operation, the device can reach high temperatures. To avoid burns and accidents, do not use the device in malfunction, and do not use spare parts that are not original.

ELECTRICAL HAZARD

Danger from electric current!
If incorrectly installed, the device can be dangerous and cause injury. Before any installation, check the data of the electrical network. Connect the device only when there is compliance. The appliance must be unpacked and checked completely before connection by a professional.

Use

WARNING
The set-up of the device installation and maintenance should only be carried out by professionals.

• Do not leave the appliance running without supervising it.
• During use, your hands should be dry.
• Do not move or tilt the device during operation.

START-UP
The device must be completely removed from its packaging and the protections must be completely removed.

• Place the device on a solid, stable, flat, and non-flammable surface.
• Do not place the appliance against the wall.
• Do not install the device near open fires or other heating devices.
• It is forbidden to place flammable objects on and near the appliance.
• Make sure that all ventilation openings are not blocked.
• Make sure that the device is placed for optimal use.
• The device must be electrically protected upstream with an adequate safety device.
• The device should be plugged directly into a wall outlet, not a power strip.
• Let the device heat up for 15 minutes before using it for the first time.

USE

• Connect the device to a grounded outlet.
• Adjust the temperature according to the foods chosen.
• Place the food in suitable containers before putting it inside.
• Some parts of the appliance can be very hot, always use protective gloves when placing or removing food.
• Turn on the interior light if necessary using the device light switch.
• Unplug the device from the power outlet when you are finished using it.

Cleaning and Maintenance

Proper cleaning and maintenance are essential for the device’s longevity and efficient performance. Follow these instructions for cleaning and maintenance:

1. Turn off the device and unplug it from the power source before cleaning.
2. Clean the device regularly with a damp cloth or sponge. Do not use abrasive materials or chemicals that may damage the surface of the device.
3. Clean the opening of the device thoroughly to prevent any leftover food or debris from blocking the passage.
4. Maintain the electrical components of the device by cleaning them regularly with a dry cloth.
5. Store the device in a dry and cool place when not in use.

Following these instructions will ensure the proper functioning of your Bin Pass-Plat device and increase its lifespan.

Safety instructions
All maintenance, cleaning, and repair of the appliance must be carried out with a disconnected appliance (isolated from all electrical sources). The use of caustic detergents and baking soda for cleaning is prohibited. Water must not get inside the device. Never immerse the device in water or other liquid. Use Casselin brand products intended for this purpose.

WARNING
The device cannot be cleaned with a direct water jet (no pressurized water jet).

Daily maintenance

Unplug the device
Clean the inside and outside of the device with a soft, damp cloth and mild detergent.
Clean the positioning grids and the body of the appliance with a soft, damp cloth and mild detergent.
Use only a soft cloth and be careful never to use abrasives or pads that may scratch the surface. After the cleaning procedure, use a soft, dry cloth to wipe and polish the surface.
Make sure the device has been cleaned properly before storing it in a dry place.

Safety instructions for maintaining the device
Daily check for damage to the power cord. Never use the appliance when the cord is damaged. If the cord is faulty, it must be replaced by a qualified technician. In the event of a fault, contact your dealer.

Any maintenance or repair must only be carried out by a professional.

REMARK
In the event of a fault, unplug the appliance, let it cool down, and contact your dealer. If the device does not start, check your power cord. The device should not be plugged into multiple sockets, but directly into a wall outlet. For any other anomaly, contact your dealer.

REMARK
Waste from used devices: any used device must, when disposed of it, comply with the regulations in force in its country *. It is essential to make the device unusable before its disposal by removing the power supply cable.

in terms of ecology and recycling

OPERATING IRREGULARITY

__

ANOMALY

| __

CAUSES

| __

EXPLANATION

---|---|---
The appliance does not work, the heating indicator light does not come on.| > The power cable is not plugged in.

  The power supply fuse has tripped.

   The power supply unit does not work.

  The safety thermostat has tripped.

  The safety thermostat is damaged.

| >      Connect the power cable properly.

  Check all of your fuses.

  Check the location of the box.

  Press the reset button located in the box.

  Contact your dealer.

The device is on but it does not heat up. The heating indicator light remains off.| >  The safety thermostat has started up.

  The resistance no longer works.

  Contact with the damaged heating element.

| Contact your dealer.
The requested temperature is not reached.| The thermostat is damaged.| Contact your dealer.
The heating element stops after a certain time.| The safety thermostat has started up.| Press the Reset button in the distribution box.

REMARK
The above-mentioned malfunctions are only given for information and remain virtual. For any hesitation, contact your dealer.

SAS CASSELIN
185 A rue Louise Labbé 69970 Chaponnay FRANCE Tel: +33 (0) 4 82 92 60 00 – Mail: contact@casselin.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>