Hyfire TAU-EXM-01 Taurus Expander Module User Guide

TAU-EXM-01 Taurus Expander Module

Product Information: TAU-EXM-01 Hyfire Taurus Expander Module The TAU-EXM-01 Hyfire Taurus Expander Module is an IP65-rated device suitable for external mounting. It comes with a back box that needs to be installed flat on the wall to retain the IP rating and prevent housing distortion, contamination, and moisture ingress. The product is available in black plastic as well with the product code TAU-EXM-01-BL. The expander module comes with a display system and a keypad to enable remote commissioning mode.

Inside the Box

• Taurus QR code
• Manual QR code
• Product code: TAU-EXM-01
• Product name: Hyfire Taurus Expander Module

Mounting Steps

1. Remove the top and bottom front plastics that cover screws, unscrew all four screws, and remove the lid from the back box.
2. Remove the electronic PCB assembly from the enclosure. The PCB is held by two Philips screws below the display, it then slides up and out.
3. Using a suitable-sized drill bit (4mm) drill the pre-defined screw mounting points in the 4 corners of the backbox.
4. Prepare apertures (20mm knockouts) required for cable access and fit appropriately rated glands.
5. Screw the back box to the wall using all fixing holes and appropriate-sized roundhead screws (do not use countersunk screws).
6. Insert cable, tighten glands, and refit PCB and securing screws.

Usage Instructions

To use the TAU-EXM-01 Hyfire Taurus Expander Module, follow the below steps:

1. Ensure that the back box is installed on the wall as flat as possible to retain IP rating and prevent housing distortion, contamination, and moisture ingress.
2. Remove the top and bottom front plastics that cover the screws, unscrew all four screws, and remove the lid from the back box.
3. Remove the electronic PCB assembly from the enclosure by unscrewing two Philips screws below the display and sliding it up and out.
4. Using a suitable-sized drill bit (4mm), drill the pre-defined screw mounting points in the 4 corners of the backbox.
5. Prepare apertures (20mm knockouts) required for cable access and fit appropriately rated glands.
6. Screw the back box to the wall using all fixing holes and appropriate-sized roundhead screws (do not use countersunk screws).
7. Insert cable, tighten glands, and refit PCB and securing screws.
8. Ensure that the discovery mode is enabled by checking the LED display system. The LED should alternate between green and yellow colors.
9. Use the keypad to navigate the display system and benefit from remote commissioning mode.

For more information on using the product, refer to the complete product manual or contact Hyfire Wireless at Unit B12a, Holly Farm Business Park, Honiley, Warwickshire, CV8 1NP. You can also reach them at +44 (0)1926 485282 or info@hyfirewireless.co.uk. Visit their website at www.hyfirewireless.com.

INSIDE THE BOX

• 1 x Expander Module
• 4 x Screws
• 1 x Quick Start guide
• 1 x QR code

IMPORTANT TO CONSIDER

When mounting a wireless device a comprehensive radio survey should have been carried out to establish the location that provides the best coverage and optimum reach. Taking into consideration the building structure and materials, the survey identifies the wireless infrastructure required and product locations for optimum performance, identifying any factor that could prevent radio integrity. Avoid fixing or mounting the unit close to the following:

• Equipment that utilizes large electrical currents
• Large metal objects or structures
• Fluorescent lighting fittings
• Metal ceiling structures
• IT cabling.

Keep 2 meters minimum spacing between other wireless equipment in the area to avoid signal interference. EN54 approved environmental temperature range is -10°C to +55°C

MOUNTING STEPS

The Expander Module is IP65 rated, suitable for external mounting. The back box must be installed on the wall as flat as possible to retain IP rating, to prevent distortion of the housing and the ingress of contamination and/or moisture.
Proceed as follows to complete the device installation.

1. Remove the top and bottom front plastics that cover screws, unscrew all four screws, and remove the lid from the back box.
2. SCREWS Remove the electronic PCB assembly from the enclosure. The PCB is held by two Philips screws below the display, it then slides up and out.
3. Using a suitable-sized drill bit (4mm) drill the pre-defined screw mounting points in the 4 corners of the backbox.
4. NO Prepare apertures (20mm knockouts) required for cable access and fit appropriately rated glands.
5. Screw the back box to the wall using all fixing holes and appropriate-sized roundhead screws (do not use countersunk screws).
6. SCREWS HOLES Insert cable, tighten glands, and refit PCB and securing screws.
   • Connect a wired EN54-4 compliant PSU to the appropriate two terminals.
   • There are also terminals for Fault Monitoring using a feed.
   • You can now apply power to the EN54-4-compliant PSU.
7. To benefit from the remote commissioning mode, ensure you leave the Expander in “discovery” mode. Using the keypad and the display system
   • Press the “Select” button.
8. Insert level 1 password (default 0001), using the arrow buttons and confirming with the “select” button.
   • Select “Expander Config” using the arrow buttons and press the “select” button.
   • Select “Set Discovery Mode” using the arrow buttons and press the “Select” button.
   • Insert the level 2 password (default 0002) using the arrow buttons and confirm with the “select” button.
   • Select discovery channel A (or B or C depending on survey results) using the arrow buttons and confirm with the “select” button.
   • Press the “select” button to start “discovery” mode as shown on the screen.
   • Press the “select” button again to confirm.
9. Ensure the LED indicates that the discovery mode is enabled, alternating green and yellow colors.
10. Screw the lid to the back box using the supplied plastic screws and refit top and bottom front plastics that cover screw housings.
    • Put the QR code available in the box either on the system map or on the dedicated pages at the end of the expander manual.

Unit B12a, Holly Farm Business Park, Honiley, Warwickshire, CV8 1NP
T: +44 (0)1926 485282, W: www.hyfirewireless.com

References

• Hyfire Wireless Fire Solutions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>