TOPDON V2200 Jump Starter User Manual

TOPDON V2200 Jump Starter

SAFETY IS ALWAYS THE FIRST PRIORITY!

READ ALL INSTRUCTIONS BEFORE USE

• For your safety, the safety of others, and to avoid any damage to the product and your vehicle, CAREFULLY READ AND MAKE SURE YOU FULLY UNDERSTAND ALL THE SAFETY INSTRUCTIONS AND MESSAGES ON THIS MANUAL BEFORE OPERATING.
• ALWAYS WEAR APPROVED SAFETY GOGGLES while working near a battery.
• ONLY use the battery clamps that come with this product.
• DO NOT use this product if the cable or the jump starter has any damage.
• DO NOT put the product under direct sunlight or in high temperature areas.
• DO NOT disassemble the product.
• WARNING: Battery acid is extremely corrosive. If acid gets into your eyes, FLUSH THEM THOROUGHLY WITH COLD RUNNING WATER FOR AT LEAST 20 MINUTES AND SEEK MEDICAL ATTENTION IMMEDIATELY.
  If battery acid gets on your skin or clothing, WASH IT IMMEDIATELY WITH A SOLUTION OF WATER AND BAKING SODA

SECTION 1 ABOUT V2200

TOPDON’s V2200 is a portable jump starter that delivers 2,200 peak amps for jump starting a 12V lead-acid battery in seconds. It supports quick and safe starts for 12V cars, boats, motorcycles, trucks, etc., with up to 8.0-liter gasoline or 6.0-liter diesel engines.

SECTION 2 WHAT’S IN THE BOX?

• V2200 Jump Starter
• Battery Clamps
• USB Cable
• User Manual
• Carrying Case

SECTION 3 PRODUCT OVERVIEW

Jump Starter

1. Power Button
   Short press to power ON; long press to turn on the LED light, then short press to toggle the LED light among the following modes: Flashlight, SOS, Strobe and OFF.

2. Battery Level Indicators
   Indicate the charge level of the internal battery.
   Note: Only jump start vehicles when the battery level of the jump starter is above 50%.

3. LED Light

4. Jump Start Socket

5. USB Output (QC3.0 12V/1.5A, 9V/2A, 5V/3A)

6. USB Output (QC3.0 12V/1.5A, 9V/2A, 5V/3A)

7. DC Output (Max 16.8V/10A)

8. Type-C Input/Output (PD60W 20V/3A, 15V/3A, 12V/3A, 9V/3A, 5V/3A)
   
   

Battery Clamps

1. Status Indicator
   Flashing red and green:
   The jumper starter is in standby mode.
   Solid green:
   The jumper starter is ready for use.
   Solid red (with buzzer ringing in the meantime): If reverse polarity, over temperature, or other error is detected.

SECTION 4 RECHARGE THE JUMP STARTER

The jump starter comes partially charged and needs to be fully charged prior to use. Please charge it through the Type-C input port once you receive it.

SECTION 5 HOW TO JUMP START A 12V BATTERY VEHICLE?

IMPORTANT
Make sure you have turned off all of the power loads of the vehicle, including headlights, radio, air conditioner, etc., before attempting to jump start the vehicle.

Note:
The jump-starting function is only applicable to 12V battery vehicles.

Step 1:
Plug the blue end of the smart battery clamps into the jump start socket.

Step 2:
Connect the battery clamps to the vehicle battery. Red clamp to the positive polarity (+), black clamp to the negative polarity (-). The status indicator will illuminate green, which indicates it is ready for jump starting. Just by clamping the terminals correctly, the V2200 delivers a jump to the battery.

Step 3:
Try starting the vehicle. If it fails, disconnect the clamps from the vehicle’s battery and wait for 20 seconds, then reconnect and try again. Do not attempt more than 3 consecutive jump starts within 2 minutes.

Note:

• The jump starter has a built-in buzzer that will ring when reverse polarity, over temperature, short circuit, or other improper connections are detected. Disconnect the clamps from the battery if the buzzer rings and connect them again after the issue is resolved.

Step 4:
After successfully jumpstarting the vehicle, remove the clamps from vehicle battery and separate the clamps and jump starter. Your jump starter will automatically power off after a few seconds.

SECTION 6 SPECIFICATIONS

• Battery Capacity 59.2Wh/16000mAh, 3.7V
• USB1 Output QC18W 12V 1.5A, 9V 2A, 5V 3A
• USB2 Output QC18W 12V 1.5A, 9V 2A, 5V 3A
• DC Output Max 16.8V 10A
• Type-C Input/Output PD60W 20V 3A, 15V 3A, 12V 3A, 9V 3A, 5V 3A
• Peak Current   2200A
• Working Temperature -10℃ to 40℃ (14 ℉ to 104 ℉ )
• Storage Temperature -20℃ to 75℃ (-4 ℉ to 167 ℉ )

SECTION 7 WARRANTY

TOPDON One Year Limited Warranty

TOPDON warrants to its original purchaser that the company’s products will be free from defects in material and workmanship for 12 months from the date of purchase (Warranty Period).
For the defects reported during the Warranty Period,
TOPDON will either repair or replace the defective part or product according to its technical support analysis and confirmation.
TOPDON shall not be liable for any incidental or consequential damages arising from the device’s use, misuse, or mounting.
If there is any conflict between the TOPDON warranty policy and local laws, the local laws shall prevail.

This limited warranty is void under the following conditions:

• Misused, disassembled, altered or repaired by unauthorized stores or technicians.
• Careless handling and/or improper operation.

Note:
All information in this manual is based on the latest information available at the time of publication and no warranty can be made for its accuracy or completeness.
TOPDON reserves the right to make changes at any time without notice.

SECTION 8 FCC

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

|

TEL

| 86-755-21612590 1-833-629-4832 (NORTH AMERICA)
---|---|---
|

EMAIL

| SUPPORT@TOPDON.COM
|

WEBSITE

| WWW.TOPDON.COM
|

FACEBOOK

| @TOPDONOFFICIAL
|

TWITTER

| @TOPDONOFFICIAL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>