CREATE WINDCALM PATIO DC Outdoor Ceiling Fan DC Motor User Manual

OUTDOOR CEILING FAN DC MOTOR
VENTILADOR TECHO EXTERIOR MOTOR DC
USER MANUAL

WINDCALM PATIO DC Outdoor Ceiling Fan DC Motor

Thank you for choosing our ceiling fan. Before using this appliance and to ensure its best use, please read the following instructions carefully.
The safety precautions listed here reduce the risk of fire, electric shock, and injury when followed correctly. Keep the manual in a safe place for future reference, as well as the
warranty, purchase receipt and box. If applicable, give these instructions to the future owner of the fan. Always follow basic safety instructions and risk prevention measures when using an electrical appliance. The manufacturer will not be held responsible for any damage resulting from the user’s failure to follow these instructions.

LIST OF PARTS

Carefully open the packaging and remove the parts that are included inside. Place them on the floor on a rug or a piece of plastic large enough to prevent any damage. Check that the objects detailed in the images below are inside the packaging.

SECURITY INSTRUCTIONS

When using any electrical appliance, the following basic safety precautions should always be observed.

• Please read this manual carefully before starting the installation. Save these instructions.
• To reduce the risk of any personal injury, attach the fan directly to the supporting structure of the building following these instructions and use only the hardware provided.
• To avoid possible electrical shock, before installing your fan, disconnect power by turning off the power switches in the electrical box and associated wall switches. If it is not possible to turn off the power switches, use a warning device such as a label on the electrical box.
• All cables must meet specifications established by local and national electrical codes and ANSI/NFPA 70. If you are not familiar with electrical installations, consult a qualified electrician.
• Do not bend the blade coupling system while installing, tilting, or cleaning the blades.
• Do not insert other objects between the fan blades.
• To reduce the risk of fire, electrical shock, or motor damage, do not use a solid-state speed governor with this fan. Only use original speed regulators.
• This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, provided they are supervised by a person responsible for their safety or have been trained in its use. the device safely. Children must not play with this appliance. They should also not carry out cleaning and maintenance tasks on the device unless they are over 8 years of age and supervised. Close supervision of children is necessary when using any appliance.

NOTE: The instructions and safety precautions that appear in this manual may not cover all possible problems and situations. You should understand that both common sense and caution are essential in the installation and use of the fan.

INSTALLATION INSTRUCTIONS

INSTALLING THE MOUNTING BRACKET

Drill a 8mm diameter hole in the concrete ceiling and insert a screw. Then align the bracket with the hole and fix it with a nut.
RECEIVER PLACEMENT

Hook the motor onto the left hook, then route the wiring.
BLADE ASSEMBLY

Tip: Blade screw washers can be placed on each screw before installing the blades. Align the holes in the blades with the screw holes in the motor. Secure and severe all screws once all blades have been hooked and installed. Before permanently attaching the screws, repeat this process with the remaining blades. Tighten the blade screws twice.

CONNECTION PANEL MOUNTING

Attach the plate to the bottom of the fan by inserting the screw heads into the designated screw holes. Thread the screws and then secure them.

LED PANEL INSTALLATION

Connect the single pin plugs on the breakout board to those on the LED panel. The LED panel is magnetized so it attaches to the backplane by simply snapping the two pieces together.
Note: While installing or removing the LED board, be careful not to touch the insulating tabs. Do not overtighten or fasten the screws as this may cause damage to the insulating tabs. Put the decorative screen on the LED plate.

CHECK INSTALLATION

• Check the correct operation of the ceiling fan, checking that there is no strange movement or misalignment in any part of the fan.
• In the event that some type of buzzing/vibration can be seen, you can proceed to adjust the blades with the balancing kit.
• In this kit you have self-adhesive weights and “u” clips.
• Turn off the ceiling fan.
• You can put the clip in the center of any blade and check if the vibration decreases.
• Turn on the fan and check. If no change is seen, turn off the fan and add another clip on another blade or use the adhesive weights.

REMOTE CONTROL

1. **Light
2. **Light intensity control
3.  Fan intensity control
4. Timer
5. Batteries (2xAAA)
6.  **Color temperature control
7. ON/OFF button
8. Reverse function

** Function only available with the LED plate installed.

• Turn on the fan by pressing the On/Off button.
• Change the direction of the air flow (winter / summer function) by pressing the reverse function button with the fan on. It doesn’t work when the fan is off. The blades will stop spinning to start again in the opposite direction by simply pressing the button once.
• Turn the light on and off by pressing the light button.
• Press the Fan Intensity Control button to increase the fan speed after power on.

REMOTE CONTROL CONNECTION

In compliance with the directives: 2012/19/EU and 2015/863/EU on the restriction of the use of hazardous substances in electrical and electronic equipment, as well as their waste disposal. The crossed bin symbol shown on the packaging indicates that the product at the end of its useful life will be collected as separate waste. Therefore, any product that has reached the end of its useful life should be delivered to waste disposal centers specialized in the separate collection of waste electrical and electronic equipment, or returned to the retailer when purchasing similar new equipment, in one for a base. Proper separate collection for subsequent commissioning of equipment sent for recycling, treatment and disposal in an environmentally compatible manner helps prevent possible negative effects on the environment and health and optimizes recycling and reuse of waste. the components that make up the device. The abusive disposal of the product by the user implies the application of administrative sanctions in accordance with the laws.

Made in P.R.C.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>