HANTECH 12019528 Camping Air Conditioner Instruction Manual

HANTECH 12019528 Camping Air Conditioner

SAFETY INSTRUCTIONS

IMPORTANT!

AIR CONDITIONERS MUST ALWAYS BE STORED AND TRANSPORTED UPRIGHT, OTHERWISE, IRREPARABLE DAMAGE MAY BE CAUSED TO THE COMPRESSOR; IF IN DOUBT WE SUGGEST WAITING AT LEAST 24 HOURS FOLLOWING INSTALLATION BEFORE STARTING THE UNIT.

WARNING When using this air conditioner, it is important that you always observe the safety regulations. This prevents the risk of personal injury, electric shock and product damage. Therefore, read all instructions beforehand.

• Read the manual before use.
• If the terms of use are not followed, the manufacturer will not be liable for any damage or injury resulting from the use of this device.
• Keep the manual, warranty certificate, and sales receipt.
• Children should be supervised to ensure that they do not play with the appliance.
• This appliance is not intended to be used by children under 8 years of age or by persons with limited physical, sensory or mental capabilities or insufficient experience and knowledge, unless they have been accompanied or have been instructed o n how to use the appliance by a person who is responsible for their safety.
• Don’t insert your fingers or any hard object to the wind guide bar of the air outlet.
• The plug should be in good condition and can’t be damaged. Never repair the device yourself if the appliance, the cord or the plug is damaged. Always have this done by the manufacturer or a qualified technician.
• The device is not suitable for commercial use.
• Always use and store the device in a dry place.
• Never use accessories that are not recommended by the manufacturer.
• Recommended operation environment temperature: 35°C.
•  This appliance is only suitable for caravan use and for the purpose for which it is intended.
• It is prohibited to modify this product (or parts of it).
• Never connect multiple electrical appliances to a power outlet. This prevents a bad connection and high heat load.
• Distance to burning objects at least 2 meters due to fire prevention measures.
• A distance of 50cm should be left between the device and other objects from the front side and 20cm should be left between the device and other objects from left and right sides.
• Users are strictly forbidden to add refrigerant themselves.
• Do not pull directly on the hose or destroy it with sharp objects. If the hose is found to be damaged, discontinue use and contact the distributor for repair.
• Details of type and rating of fuses: 250VAC, T3.15A

Installation location of the air conditioner

The air conditioner must be placed on a firm, flat surface (note: the air conditioner must not be tilted or tilted) when the appliance is in use. This air conditioner may not be installed in the following places:

• Near strong heat sources, vapors, and flammable or explosive gas.
• In an environment that contains chemicals (evaporating substances, organic solvents, etc.), as soon as it rains, the air conditioning must be removed from the window.

Also, take the following regulations into account:

• The product must be kept upright at all times and in all cases. Do not hold the device sideways or upside down.
• try to keep the air conditioner straight when moving or carrying it. Make sure it is not shaken or dropped.
• Make sure the air supply is not clogged and remains well-ventilated.
• Do no insert objects through the openings of the air inlet and outlet. Objects can en counter electrical parts or the fan in this way and could be dangerous.
• Do not place heavy objects on the product.
• Remove the plug from the socket before moving the air conditioner, performing maintenance, cleaning or not using it for a long time.
• Do not pull the plug to move the machine.
• Clean the dust screen of the air supply at least once a month.
• If the machine will not be used for a long time, it must be stored in a cool and dry p lace. Clean and dry the air conditioner well in advance.

TECHNICAL DATA

46 dB
Dimensions outside unit| 44Qx215x355mm| Net weight| 20,5kg

PACKING LIST

DESIGNATION OF PARTS

ACCESSORIES

OPERATION OF CONTROL PANEL

CD POWER

• Press this key to turn the device on and off. When the air conditioner is switched on, the temperature is set to 22° C by default. The temperature sensor measures the ambient temperature and if exceeds 22° C, the outdoor unit starts to work to bring the temperature down. If the ambient temperature is already below 22° C, then the outdoor unit does not start.

MODE

• Press this key to select cooling, fan, and dehumidification modes; In standby/turned on mode, by pressing this key to set timing on/off.

TEMPERATURE/ TIME ADJUSTMENT

• In cooling mode, press the key to increase or decrease the temperature, the setting temperature adjustable from 16~30° C; In timer mode, press the key to adjust the time to turn on/turn off the machine.  Press the Up/Down key at the same time to transfer between ° C and ° F.

FAN SPEED

• Press the key to choose low/high fan speed.

SLEEP MODE

• Press the key to enter or quit sleep mode. After 20 seconds, all lights and the digital display turn off and the air conditioner goes to sleep. The indoor unit fan continues to run at low fan speed.

DISPLAY WINDOW

• Check the temperature and time from this window.

SWING

• Press the fan speed and sleep mode keys at the same time to turn on/off swing function.

INSTALLATION OF THE AIR CONDITIONER

1. Unpack the machine and accessories and check that the hose between the indoor and outdoor unit is properly connected. Also check whether the condensation drain has a rubber cover. Finally, check whether the accessories are complete.
2. Install the accessories as shown in the picture. Connect the outer bracket to the support block and the inner bracket by tightening the M6 screws. This is how you form the carrying handle.
   • Place the shockproof rubber dampers on the back of the outdoor unit.
   • Install the bracket as shown in the figure below. Install the indoor and outdoor units on the bracket to fix the two parts. To secure the units to the bracket, tighten the M6 screws in the appropriate holes.
   • Install the indoor unit on the bracket and tighten the bracket properly. Next, wrap the protection sleeve on the hose between the outdoor and indoor unit. (See the illustration below ) 
   • Install the complete unit in the caravan window and tighten the bracket properly.

ERROR CODE LIST

Error codes

Error code| Cause| Solution
FL| Water full alarm| Take off the rubber stopper and empty the water.
E1| System temperature sensor fault| Replace System temperature sensor
E2| Room temperature sensor fault| Replace room temperature sensor
EF| Indoor motor fault| Replace the motor.
Eb| Lack of fluorine| Contact the dealer

E4

|

Freeze protection

| Check that the air outlet is not blocked, and keep the air deflector open.

TROUBLESHOOTING GUIDE

Failure guide

Problem| Cause| Solution

The device does not turn on

| No power| Turn power on
Damaged electrical outlet| Turn off the power and
Unknown reason| check/repair the power outlet

Little air displacement or limited cooling effect

| The lowest ventilation setting is selected| Contact the dealer

Select the high ventilation speed mode

The air filter is dirty| Check and clean the filter
The air supply or exhaust of the indoor unit is blocked| Check that the unit is not blocked and remove the obstruction
The air supply or exhaust from the outdoor unit is blocked| Check that the unit is not blocked and remove the obstruction
The ambient temperature is too low or too high| Die Umgebungstemperatur muss zwischen 18 und 40 liegen°C
Insufficient voltage from the power supply| Consult an installer or use a different power connection
Failure guide

Air displacement only but no cooling effect

| The device runs in ventilation mode| Select the cooling mode(NC)
The cooling mode has just turned off automatically| Wait about 3-5minutes until

the thermostat switches on again

Abnormal sounds or vibrations

| The mounting brackets are not properly installed on the vehicle, or the device mounting screws are not sufficiently tightened| Check that the mounting bracket is tight and tighten the device mounting screws

Water is leaking from the indoor unit

| ****

The rubber stopper on the bottom of the indoor unit is missing or is not pressed enough

| ****

Check or replace the rubber stopper

The device is at an angle| The device must be mounted horizontally (maximum angle <3°C
The appliance emits a related odor| There is a serious problem| Switch off the device

immediately and contact the dealer

MAINTENANCE

Declaration:

1. Ensure the machine is unplugged before maintenance.
2. Do not use gasoline or other chemicals to clean the unit;
3. Do not wash the unit directly;
4. If the air conditioner is damaged, please contact the dealer or repair shop.

Cleaning

Caution: Unplug the power cord before cleaning the maintenance.

Air filter

• It is important to regularly remove the dust from the filter.
• Remove the filter as shown in the picture below.
• Clean the filter with tap water and I or a vacuum cleaner to remove any dirty from the filter.
• Do not use water hotter than 40° C for cleaning and do not expose the filter to the sun.
• Make sure the filter has dried before putting it back in the air conditioner.

Clean the Air-conditioner Surface

• First, clean the surface with a neutral detergent and a wet cloth;
• Then dry the device thoroughly with a dry cloth.
• Do not allow water or deterrents to enter the machine.
• Do not clean the air conditioner with an aggressive cleaning agent and/or petrol.

Storage

If you are planning to store the machine without needing to use it for a long time, please remove the drain cover from the drainage hole at the bottoms both of indoor unit and outdoor unit, and drain all the condensation water appropriately in available place.

1. Remove the unit from the window.
2. Remove the rubber seal from the indoor unit and outdoor unit, drain the condensate water.
3. Keep running in fan mode to make the internal dry.
4. Turn off the conditioner and pull down the plug.
5. Wash the filter then install.
6. Remove all the brackets on the air conditioner, install the brackets of the indoor unit on the outdoor unit, assemble as shown in the figure below, and then store the unit against the wall.
7. Store the air conditioner in a cool and dry place.
8. We recommend that you put the air conditioner back in its packaging when you store it. This prevents dirt and dust from collecting on the air conditioner.

SMART HOME WIFI CONNECTION GUIDE

Network Module Features

802.11n(20MHz): OFDM

Fixed frequency software| SecureCRT.exe
Antenna Gain| 2.5dBi
Type of antenna| PCB
Transmit power| 20dBm

Install App

Download the “Smart life” app from the Play Store (Android) or App Store (iOS).

Scan QR code

Register

If you do not have a Smarter Home account, register or sign in with a verification code sent by SMS.

To register:

1. Tap to enter registration page
2. The system automatically recognizes your country/ area. You can also select your country code manually. Enter your mobile phone number/ email address and tap “Next”.
3. If you choose the mobile phone number option, then enter the verification code in the message sent to you by SMS. Set a password as prompted and press “Confirm” to finish your registration.

Add Device Through Network

1. Power the conditioner on, when the conditioner is under standby mode, press the “FAN” button for 3 seconds to enter Wifi-connect mode.
2. Open the Smart Home app and tap “+” in the upper right to add a new device through the network.
3. Ensure the device’s indicator light rapidly flashes (2 times per second) and tap “Confirm light is rapidly flashing”.
4. Select Wi-Fi network (note: network must be 2.4Ghz band) and enter the password. The device will commence the pairing process and connect to the app.
5. After successfully configuring the devices, the AC will be shown on the smart home page. Tap to enter its control page.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>