MIBOXER FUT039W RGB+CCT LED Controller Instruction Manual

MIBOXER FUT039W RGB+CCT LED Controller

Features

This product uses WiFi + Bluetooth + 2.4G wireless transmission technology, low power consumption, strong anti-interference ability.

WiFI+ Bluetooth connect network can greatly enhance the connect network experience. When the router is disconnected, Bluetooth can also directly connect and control equipment at close range. After successful network configuration using [MiBoxer Smart] app to achieve wireless dimming, remote control, group control, scene control, timing control, music movement, biorhythm, sleep plan, wake plan, one key execution, automation, etc. functions. And it supports 2.4G remote control.

• 16 Millions of colors to choose
• Color temperature adjustable
• Dim brightness/Saturation
• 2.4G RF wireless transmission technology
• WiFi wireless control support long-range control
• Auto-transmitting & Synchronization (only for remote control dimming)
• Device sharing
• Tap-to-Run & automation
• Timing setting/ countdown turn on/off LED light
• DMX512 controllable (DMX512 LED transmitter is needed)
• Remote control
• Control distance 30m
• Smartphone app control
• Support third-party voice control
• Group control
• Biorhythm
• Support music rhythm
• Sleep/wakeup plan
• Support scene customization
• Do not disturb mode

Dynamic mode table selection (only for remote control)

1. Select dynamic mode table 1: The light is powered off for 10 seconds and then powered on. Within 3 seconds, press the ” S+ ” button 5 times, the blue light blink 3 times slowly, indicating successfully.
2. Select dynamic mode table 2: The light is powered off for 10 seconds and then powered on. Within 3 seconds, press the “S- ” button 5 times, and the yellow light blink 3 times slowly, indicating successfully.

Dynamic mode table 1 (default)

Adjustable

2| Automatic color change
3| Sam
4| Gemstone
5| Twilight
6| American
7| Fat Tuesday
8| Party
9| Slow Color Splash

Dynamic mode table 2 (need to switch manually)

Adjustable

2| White light Gradual change
3| RGB gradual change
4| Seven colors jump to change
5| Jump to change randomly
6| Red light gradual change

+Flash 3 times

7| Green light gradual change

+Flash 3 times

8| Blue light gradual change

+Flash 3 times

9| White light gradual change

+Flash 3 times

Auto transmitting & Synchronization

(only for remote control)

Signal transmitting
One light can transmit the signals from the remote control to another light within 30m, as long as there is a light within 30m, the remote control distance can be limitless.

Modes synchronization
Different lights can work synchronously when they are started at different times, light by the same remote, under same dynamic mode and within 30m distance.

The same dynamic mode, the same speed can be synchronized.

Linking Code/Unlinking Code Instructions

Linking Code Instructions

1. Switch off light, after 10 seconds then switch on again.
2. Short press I” button 3 times within 3 3 seconds when light on.
3. Lights blink 3 times slowly means linking is done successfully.

Linking failed if light is not blinking slowly, Please follow above steps again. (Note: Light that have linked can’t link again)

Unlinking Code Instructions

1. Switch off the light, after 10 seconds then switch on again.
2. Short press the” I” button 5 times within 3 seconds when the light on.
3. Lights blink 10 times quickly means unblinking is done successfully.

Unlinking failed if light is not blinking quickly, Please follow above steps again. (Note: Light haven’t linked that don’t need to unlink)

Compatible with these remote controls (Purchased separately)

PWM high-frequency/low-frequency switching

Switch to high frequency (6KHz): on the condition of turning on the light

1. Short press the “OFF button of the remote control once;
2. Short press the “ON” button 5 times within 3 seconds, and the white light blinks 2 times quickly, indicating successfully.

Switch to low frequency (400Hz): on the condition of turning off the light

1. Short press the “ON” button of the remote control once;
2. Short press the “OFF” button 5 times within 3 seconds, and the white light blinks 2 times slowly, indicating successfully.

DMX512 LED Transmitter Link/Unlink

Compatible with DMX512 LED Transmitter (Purchase separately

1. Choose the zone for the light by pressing “+ ” or”-” (e.g. “CH12” means zone 12)

2. Link
   Switch off the light, after 10 seconds switch on again

3. When the light is on, short press “ ” 3 times within 3 seconds

4. The light blinks slowly 3 times, means the linking is done successfully

Unlink

• Switch off the light, after 10 seconds switch on again
• When the light is on, short press “ ” 5 times within 3 seconds
• The light blink quickly 10 times, means the unlinking is done successfully

If the link or unlink failed, please follow the above steps again.

DMX512 LED Transmitter Connection Diagram

Smartphone app control

1. Download and install the [MiBoxer Smart] or [Tuya Smart] app
   Search for [MiBoxer Smart] or [Tuya Smart] in Apple or Google store or scan the following QR code to download and install the app.
   Please click ” Register ” button to create an account while using it in the first time, Log in directly if you already had an account.

2. Network Configuration

3. Connect controller with power supply.

4. Confirm indicator light is flashing quickly (2 flashes per second),
   If the indicator light isn’t in a fast flashing state, there are two ways to enter:

  * Long press the ” SET ” key until the indicator light flashes quickly.
  * Power off and on the controller 3 times.

3. Connect the phone to the home WiFi network in a 2.4GHz frequency.

4. Open the homepage of the app and click the” + ” button at the upper right corner of page.
   MiBoxer Smart app:
   

5. Click ” WiFi Lighting ” on the left side of page and then click ” LED Controller “
   Tuya Smart app:
   Click ” Lighting ” on the left side of page and then click ” Light Source (BLE+Wi-Fi) ”

6. Follow the app prompts to complete the configuration.

Scan QR code to watch video instruction

Attention

1. Please check whether the voltage of the power supply is in accordance with the light, and please check the connection of both the cathode and anode, otherwise, the light will be broken.
2. Please don’t connect wires with power on. Please turn on again only when it is in the right connection and no short circuit.
3. Non-professional user cannot dismantle the lighting fixtures directly.
4. Please do not use the light in a place with widely range metal area or strong electromagnetic waves nearby, otherwise, the remote distance will be seriously affected.

Made in China.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>