ATEN AS104 Coaxial Ceiling Loudspeakers User Manual
- June 9, 2024
- Aten
Table of Contents
- Compliance Statements
- User Information
- User Notice
- Product Information
- Package Contents
- About this Manual
- Conventions
- Overview
- Features
- Planning the Installation
- Components
- Hardware Setup
- Operation
- Safety Cable Anchor
- Adjusting the Tap Selector
- Safety Instructions
- Technical Support
- Specifications
- Limited Warranty
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
AS104 Coaxial Ceiling Loudspeakers
User Manual
Compliance Statements
RoHS
This product is RoHS compliant.
User Information
Online Registration
Be sure to register your product at our online support center:
International http://eservice.aten.com
Telephone Support
For telephone support, call this number:
International | 886-2-8692-6959 |
---|---|
China | 86-400-810-0-810 |
Japan | 81-3-5615-5811 |
Korea | 82-2-467-6789 |
North America | 1-888-999-ATEN ext. 4988 |
User Notice
All information, documentation, and specifications contained In this manual
are subject to change without prior notification by the manufacturer. The
manufacturer makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any
warranties as to merchantability or fitness for any particular purpose. Any
of the manufacturer’s software described in this manual i s sold or licensed
as is. Should the programs prove defective following their purchase, the
buyer (and not the manufacturer, its distributor, or its dealer), assumes the
entire cost of all necessary servicing, repair and any incidental or
consequential damages resulting from any defect in the software.
The manufacturer of this system is not responsible for any radio and/or TV
interference caused by unauthorized modifications to this device. It is the
responsibility of the user to correct such interference.
The manufacturer is not responsible for any damage incurred in the operation
of this system if the correct operational voltage setting was not selected
prior to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS CORRECT BEFORE
USE.
Product Information
For information about all ATEN products and how they can help you connect
without limits, visit ATEN on the Web or contact an ATEN Authorized Reseller.
Visit ATEN on the Web for a list of locations and telephone numbers:
International http://www.aten.com
North America http://www.aten-usa.com
Package Contents
Check to make sure that all the components are in working order. If you encounter any problem, please contact your dealer.
- 2 AS104/AS106 4” (AS104) / 6.5” (AS106) Coaxial Ceiling Loudspeakers
- 2 Autoblock connectors
- 2 ceiling reinforcement kits
- 2 cutout templates
- 2 speaker grilles
- 2 user instructions
About this Manual
This user manual i s provided to help you get the most from the AS104 / AP 106
unit. It covers all aspects o f installation, configuration, and operation. An
overview o f the information found in the manual is provided below.
Chapter 1 , Introduction introduces you to the Coaxial Ceiling Loudspeakers.
Its purpose, features, installation considerations, and panel components are
presented and described.
Chapter 2, Hardware Setup describes the steps that are necessary to quickly
and safely set up your installation.
Chapter 3, Operation explains the audio source input operation using the
Coaxial Ceiling Loudspeakers and its limitations.
Appendix, provides a list of safety instructions and precautions, contact
information for ATEN technical support, product specifications, and other
technical information.
Note:
- Read this manual thoroughly and follow the installation and operation procedures carefully to prevent any damage to the unit or any connected devices.
- This product may be updated, with features and functions added , improved or removed since the release of this manual. For an up-to-date user manual, visit http://www.aten.com/global/en/
Conventions
This manual uses the following conventions:
Indicates text that you should key in.
Indicates keys you should press. For example, [Enter] means to press the Enter
key. I f keys need to be chorded, they appear together in the same bracket
with a plus sign between them: [Ctrl+Alt].
Numbered lists represent procedures with sequential steps.
Bullet lists provide information, but do not involve sequential steps.
Indicates selecting the option (on a menu or dialog box , for example), that
comes next. For example, Start > Run means to open the Start menu, and then
select Run.
Indicates critical information.
Overview
The AS104 / AS106 comes in a pair of 4 ” / 6.5” coaxial 2-way ceiling
loudspeakers that deliver decent sonic performance. Each speaker ships with a
4” /6.5” woofer, 20 mm dome tweeter, and 30 W RMS, 60 W peak (8 Q) / 60 W
RMS, 120 W peak (8 Q) power handling capability. Excellent and consistent
sound quality i s ensured by taking advantages of its 100 – 20 kHz / 80 – 20
kHz bandwidth and wide coverage, allow in g less speakers used to cover the
listening area to lower the cost of the system installed.
The loudspeaker contains a matching transformer, running comfortably on 70 /
100 V lines or at 8 Q to suit various application demands. Phase issues are
minimized as result of the adoption of the coaxial neodymium magnetic driver,
making sound waves with various frequency bands easier to be added together
instead o f canceling each other out. Made of UL94-V0-compliant flame
retardant materials, the housing, together with the Zinc-coated steel back
can, improve safety for applications where flame and fire protection is of
the highest importance. When it comes to installation, each speaker features a
cutout template for quick and easy post construction installation and can be
secured with its dog-leg mounting system. The paintable magnetic grille
assures effortless installation and cleaning while giving unobtrusive
appearance in any room design.
AS104/ AS106 is ideal for residence and enterprise-grade audio applications,
such as auditoriums, houses of worship, sports venues, and any small or
midsized commercial spaces that require a clear and intelligible sound
solution without compromise on life safety.
Features
- Coaxial design with premium components:
- 4°/6.5” high output driver with rubber surround and heavy-duty voice coil
- 20mm dome tweeter
- 100 – 20 kHz (AS104) / 80 – 20 kHz (AS106) bandwidth with wide coverage for consistent, full-range coverage of the space while reducing the amount of the speakers needed
- Switchable for use as either an 8 Q low-impedance speaker or as part of a 70V / 100V distributed loudspeaker system
- UL94-V0 compliance for life safety applications
- Paintable magnetic grille for blending into any room décor
- Ease of installation guaranteed with the magnetic grille, dog leg mounting system and cutout template
Planning the Installation
Requirements
Prepare the following before installing the AS104 / AS106 unit:
- 1 amplifier
- 1 or more audio source devices
Components
Hardware Overview
No. | Component | Description |
---|---|---|
1 | terminal ports | Connects to an amplifier or other speaker via a 5.08 mm |
Autoblock connector.
2| tap selector| Adjusts the speaker impedance.
3| terminal cover (AS106 only)| Secures the wirings pipe in place.
4| rotating mount tabs (dog-legs)| Mounts the speakers to the ceiling tiles.
This Page Intentionally Left Blank
Hardware Setup
- Please review the safety information regarding the placement of this device in Safety Instructions, page 13.
- Do not power on the AS104 / AS106 until all the necessary hardware is connected.
Connecting the AS104 / AS106 Unit
Follow the steps below to connect the AS104 / AS106 to an amplifier.
-
Use the cutout template as a guide to cut a hole on your ceiling tile.
-
Do the following to enhance the stability of the AS104 / AS106 speakers installed on the ceiling tile:
a ) Insert and screw the C-bracket on the V – rails.
b) Insert both ends o f the V-rails on to a suspended ceiling. -
Strip solation back about 5 mm on self-sup plied speaker wires.
-
Insert the wire leads into the Autoblock connector and screw the hold down screw until tight.
Note:
Please do not tin the wire leads when connecting the Autoblock connector. Tinned wires may influence the sound quality and could be pulled out easily.
To avoid rattling from the vibration, tighten any unused hold-down screws. -
Based on your application type, refer to the corresponding diagram to connect the terminal ports on the AS104 / AS106 to your output device.
Note:
If you are connecting the terminal ports on the AS106, please slide the terminal cover open by loosening the screws.
Make sure the tap selector on the speakers Is set to a proper position, please refer to your power amplifier settings before adjusting the tap selector.
For Low-Z output, make sure the tap selector on the speakers Is set to 8R position. -
Screw the four rotating mount tabs (dog-legs) tightly to the ceiling tile.
-
Attach the speaker grilles onto the AS104 / AS106 speakers.
Operation
Frequency Response Chart
Polarity
Safety Cable Anchor
A safety cable anchor is available on the back of each unit for securing the speakers in case the ceiling tile breaks. Please do not omit this step. ATEN strongly recommended to secure the speakers using its safety cable anchors to a separate secure point.
Adjusting the Tap Selector
A tap selector can be found on the front baffle of each unit. It is necessary to adjust to tap selector before powering on the speaker and attaching the speaker grille. Turn the selector clockwise to adjust the distributed system tap settings.
Safety Instructions
General
- This product is for indoor use only.
- Read all of these instructions. Save them for future reference.
- Follow all warnings and instructions marked on the device.
- Do not place the device on any unstable surface (cart, stand, table, etc.). If the device falls, serious damage will result.
- Do not use the device near water.
- Do not place the device near, or over, radiators or heat registers.
- The device cabinet is provided with slots and openings to allow for adequate ventilation. To ensure reliable operation, and to protect against overheating, these openings must never be blocked or covered.
- The device should never be placed on a soft surface (bed, sofa, rug, etc.) as this will block its ventilation openings. Likewise, the device should not be placed in a built in enclosure unless adequate ventilation has been provided.
- Never spill liquid of any kind on the device.
- Unplug the device from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
- The device should be operated from the type of power source indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company.
- To prevent damage to your installation it is important that all devices are properly grounded.
- Do not allow anything to rest on the power cord or cables. Route the power cord and cables so that they cannot be stepped on or tripped over.
- Position system cables and power cables carefully; Be sure that nothing rests on any cables.
- Never push objects of any kind into or through cabinet slots. They may touch dangerous voltage points or short out parts resulting in a risk of fire or electrical shock.
- Do not attempt to service the device yourself. Refer all servicing to qualified service personnel.
- Ifthe following conditions occur, unplug the device from the wall outlet and bring it to qualified service personnel for repair.
- The power cord or plug has become damaged or frayed.
- Liquid has been spilled into the device.
- The device has been exposed to rain or water.
- The device has been dropped, or the cabinet has been damaged.
- The device exhibits a distinct change in performance, indicating a need for service.
- The device does not operate normally when the operating instructions are followed.
- Only adjust those controls that are covered in the operating instructions, Improper adjustment of other controls may result in damage that will require extensive work by a qualified technician to repair.
Technical Support
International
- For online technical support — including troubleshooting, documentation, and software updates: http://support.aten.com
- For telephone support, see Telephone Support, page 111:
North America
Email Support | support@aten-usa.com |
---|---|
Online Technical Support | Troubleshooting |
Documentation
Software Updates| http://www.aten-usa.com/support
Telephone Support| 1-888-999-ATEN ext 4988
When you contact us, please have the following information ready beforehand:
- Product model number, serial number, and date of purchase
- Your computer configuration, including operating system, revision level, expansion cards, and software
- Any error messages displayed at the t i m e the error occurred
- The sequence o f operations that led up to the error
- Any other information you feel may be of help
Specifications
Function I AS104
System Specification
LF Driver| 4″ Paper Cone with Rubber Suspension
HF Driver| 20 mm PEI Dome Tweeter
Frequency Response| 100 — 20 kHz (-10 dB)
Distortion| <= 5%
Rated Power| 30Wrms / 60Wpeak
Sensitivity| 86 dispel, @ 1 m, 1W, 1 kHz
Transformer Taps| 70V (2.5W, 5W, 10W, and 20W) 100V (*, 5W, 10W, and 20W)
Compliance
Certification CE, WEEE, Rolls
Connectors
Audio Inputs I 5.08 mm Autoblock Connector
Environmental
Operating Temperature| 0 – 40°C
Humidity| 0 – 80% RH, Non-Condensing
Storage Temperature| -20 – 60°C
Physical Properties
Weight| 2.20 kg (4.85 lb)
Housing| UL94-VO ABS Plastic Baffle Zinc-Coated Steel Backman
Dimensions (L x W x H)| 21.80 x 21.80 x 13.00 cm (8.58 x 8.58 x 5.12 in)
Color| White Speaker Grille (Paintable) White Speaker Baffle
Cut-out Diameter| 182 mm
In-ceiling Clearance Height| 125 mm
Carton Lot| 2 Pcs / Carton
Function I AS106
System Specification
LF Driver| 6.5″ Paper Cone with Rubber Suspension
HF Driver| 20 mm PEI Dome Tweeter
Frequency Response| 80 — 20 kHz (-10 dB)
Distortion| <= 5%
Rated Power| 60Wrms / 1200Wpeak
Sensitivity| 90 dBSPL, @ 1 m, 1W, 1 kHz
Transformer Taps| 70V (7.5W, 15W, 30W, and 60W) 100V (*, 15W, 30W, and 60W)
Compliance
Certification I CE, WEEE, Rohus
Connectors
Audio Inputs I 5.08 mm Autoblock Connector
Environmental
Operating Temperature| 0 – 40°C
Humidity| 0 – 80% RH, Non-Condensing
Storage Temperature| -20 – 60°C
Physical Properties
Weight| 3.70 kg (8.15 lb)
Housing| UL94-VO ABS Plastic Baffle Zinc-Coated Steel Backcan
Dimensions (L x W x H)| 25.72 x 25.72 x 19.75 cm (10.13 x 10.13 x 7.78 in)
Color| White Speaker Grille (Paintable) White Speaker Baffle
Cut-out Diameter| 221 mm
In-ceiling Clearance Height| 195 mm
Carton Lot| 2 Pcs / Carton
Limited Warranty
ATEN warrants its hardware in the country of purchase against flaws in materials and workmanship for a Warranty Period of two [2] years (warranty period may vary in certain regions/countries) commencing on the date of original purchase. This warranty period includes the LCD panel of ATEN LCD KVM switches. Select products are warranted for an additional year (see A+ Warranty for further details). Cables and accessories are not covered by the Standard Warranty.
What is covered by the Limited Hardware Warranty
ATEN will provide a repair service, without charge, during the Warranty
Period. If a product is detective, ATEN will, at its discretion, have the
option to (1) repair said product w i t h new or repaired components, or (2)
replace the entire product with an identical product or with a similar product
which fulfills the same function as the defective product. Replaced products
assume the warranty of the original product for the remaining period or a
period of 90 days, whichever i s longer. When the products or components are
replaced, the replacing articles shall become customer property and the
replaced articles shall become the property of ATEN.
To learn more about our warranty policies, please visit our website:
http://www.aten.com/global/en/legal/policies/warranty-policy/
© Copyright 2022 ATEN® International Co., Ltd.
Released: 2022-11-07
ATEN and the ATEN logo are registered trademarks of ATEN International Co.,
Ltd. All rights reserved.
All other brand names and trademarks are the registered property of their
respective owners.
References
- eService System
- USA Location information - USA.com
- ATEN - Simply Better Connections | ATEN U.S.A.
- Downloads | ATEN Corporate Headquarters
- ATEN - Simply Better Connections | ATEN Corporate Headquarters
- ATEN Product Warranty | ATEN Corporate Headquarters
- A+ Warranty | ATEN Corporate Headquarters
- LCD KVM Switches / Consoles | ATEN Corporate Headquarters
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>