LEE 91582 App Swage Kit User Manual

June 9, 2024
LEE

LEE 91582 App Swage Kit

LEE 91582 App Swage Kit

APP SWAGE KIT

App Swage Kit

Set up swage holder with correct swage punch and shell holder

  1. Unscrew swage cap over a clean table top and lift off swage holder.
    Set up swage holder with correct swage punch and shell
holder

  2. Remove shell holder adapter, spring and swage pin and disc spring assembly.
    Set up swage holder with correct swage punch and shell
holder

  3. Slide shell holder adapter into swage holder
    Set up swage holder with correct swage punch and shell
holder

  4. Slide appropriate shell holder into exposed slot. IMPORTANT: shell holder must be installed in the adapter before reinstalling swage punch assembly.
    Set up swage holder with correct swage punch and shell
holder

  5. Install spring into shell holder adapter followed by the correct swage punch assembly (small or large).
    Set up swage holder with correct swage punch and shell
holder

  6. Re-install swage cap, finger tighten.
    Set up swage holder with correct swage punch and shell
holder

  7. Do not install O-ring if using X-PRESS shell holders. If using a universal press shell holder, install O-ring to prevent shell holder rotation. The X-PRESS shell holders need to be able to float/ rotate to allow damaged or out of round rims to pass through without interference.
    Set up swage holder with correct swage punch and shell
holder

HOW TO USE

  1. Install correct swage push rod in die the small diameter push rod is used for 22 caliber cases. The large push rod is for larger caliber cases.
    Do not use the small push rod when swaging large primer pockets else the case bottom will deform and permanently damage the case.
    How To Use

  2. Install swage push die in upper press casting. Tighten clockwise with adjustable wrench.
    How To Use
    Note: It is important to use a wrench, a finger tightened swage push die will back out during use if not securely tightened.

  3. Install appropriate swage holder (small/large)in APP base casting. Secure with wrench.
    How To Use
    Note: use a wrench, a finger tightened swage holder will back out during use if not securely tightened.

  4. Lower the press lever and screw the swage push punch in until it meets the small or large swaging punch.
    How To Use

  5. Place a case that you wish to swage in the shell holder. Lower the press lever, notice that the connecting link will not meet the stops on the upper casting (PHOTO 1 & 2). Release the pressure on the press lever and unscrew the push rod in ¼ turn increments, apply approximately 25 pounds of pressure on the lever of the press and observe if the connecting link meets the stop (PHOTO 2). Continue to unscrew the swage push punch in ¼ turn increments until the connecting links meet the stop with 25 pounds of pressure applied to the lever. When you have it set, lower the lever, and tighten the knurled lock nut.
    How To Use
    How To Use
    The best way to determine if you have sufficient swage on the primer pocket is to try seating a primer. If the primer starts and seats properly you have sufficient swage. As the tool is designed, it is impossible to swage excessively.
    If you misadjust the push punch too deeply, the only consequence is the press lever will be very difficult to push to the stops. Adjusting to apply the least amount of swage to allow easy seating of primers will make the tool more pleasant to use.

Swage Push Die:

Swage Push Die:

Push rod Punch size Cartridges
30 cal. #PA4392 Large #91566 45 ACP, 308 Win, 30-06
22 cal. #PA4395 Small #91565 223 Rem, 5.56 NATO, 300 Blackout
22 cal. #PA4395 Small #91565 40 S&W, 9mm Luger

Lee Guarantee

LEE RELOADING PRODUCTS are guaranteed not to wear out or break from
normal use for two full years or they will be repaired or replaced at no charge if returned to the factory. Any Lee product of current manufacture, regardless or a gear condition, will be reconditioned to new with a new guarantee, if returned to the factory with payment equal to one half the current retail price.

How To Use

image source: http://ammunitiontogo.com

Attention:
All cases must be decapped before swaging. Most foreign military brass is Berdan primed and can not be deprimed with this product. Look inside the case, it must have one central flash hole

23 / 5.56 NATO users: Your kit includes a decapping die fitted with our decapping and flaring rod. If you are swaging 223 / 5.56 NATO cases, you must use this die. The slight flare provides easy entry of the swage punch into the case mouth. The tapered flare punch also rounds the necks that may have been driven over by a tank or HUMVEE. Some crimped in primers are very difficult to remove and may slide the decapper upward. If this happens, tap the decapper flush with the top of the hex clamp. Securely tighten with a 3/4” wrench on the die body and �” wrench on the decapper clamp.
How To Use

Install the decapping and flare die until it touches the shell holder.
Tighten Philips screw on spline drive lock-ring.
How To Use

Guided decapper helps align the case to reduce the chance of bending or breaking a decapper.

Caliber| Product
17 cal. & 204 Ruger| 91574
6mm to 25 cal.| 91577
27 cal. to 7mm.| 91578
34 cal. to 35 cal.| 91581
40 cal.| 91583
45 cal.| 91584

WARNING: Handling live primers and spent primers may expose you to lead or other chemicals, which are known to the State of California to cause reproductive harm and cancer. For more information, go to www.P65Warnings.ca.gov.
WARNING: This product may contain steel alloyed with trace amounts of lead and other elements which are known to the State of California to cause reproductive harm and cancer. For more information, go to www.P65Warnings.ca.gov.
To prevent exposure, do not alter the product by welding, grinding, etc.

4275 COUNTY ROAD U ·
HARTFORD WI 53027
www.leeprecision.com

LEE Logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals