vtech LF925HD 5 Inch WiFi High Definition Pan and Tilt Monitor Instruction Manual

vtech LF925HD 5 Inch WiFi High Definition Pan and Tilt Monitor

Important Safety Instructions

The applied nameplate is located at the bottom of the Baby Unit’s base.
When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:

1. Follow all warnings and instructions marked on the product.

2. Adult setup is required.

3. CAUTION: Do not install the Baby Unit at a height above 2 meters.

4. This product is not a substitute for adult supervision of the infant. Supervising the infant is the parent’s or caregiver’s responsibility. This product could cease operating, and therefore you should not assume it will continue working properly for any given period of time. Further, this is not a medical device and should not be used as such. This product is intended to assist you in supervising your baby.

5. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower.

6. CAUTION: Use only the battery provided in the product. There may be a risk of explosion if a wrong type of battery is used for the Parent Viewer. The battery cannot be subjected to high or low extreme temperature and low air pressure at high altitude during use, storage or transportation. Disposal of battery into fire or a hot oven, or mechanically crushing or cutting or the battery can result in an explosion. Leaving the battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid of gas. Battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas. Dispose of used battery according to the instructions.

7. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product.
   Power adapter information: Baby Unit Output: 5V DC 1.5A; VTech Telecommunications Ltd.; Model: VT07EEU05150 Parent Viewer Output: 5V DC2A; VTech Telecommunications Ltd.; Model: VT07EEU05200
   Rechargeable battery information: Zhuhai Great Power Energy Co., Ltd. Lithium battery, 3.7V 5000mAh; Model: GSP806090-5Ah-3.7V-1S1P

8. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.

9. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible.

10. Unplug this product from the wall outlet before cleaning.

11. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation.

12. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped.

13. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the  type of power supply in your home, consultyour dealer or local power company.

14. Do not overload wall outlets or use an extension cord.

15. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.

16. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register.

17. Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product.

18. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the product other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.

19. You should test the sound reception every time you turn on the units or move one of the components.

20. Periodically examine all components for damage.

21. There is a very low risk of privacy loss when using certain electronic devices, such as baby monitors, cordless telephones, etc. To protect your privacy, make sure the product has never been used before purchase, reset the baby monitor periodically by powering off and then powering on the units, and power off the baby monitor if you will not use it for some time.

22. Children should be supervised to ensure that they do not play with the product.

23. The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

SAVE THESE INSTRUCTIONS

Cautions

1. Use and store the product at a temperature between 32˚F (0˚C) and 104˚F (40˚C).

2. Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source.

3. Batteries should not be exposed to excessive heat such as bright sunshine or fire.

4. Warning—Strangulation Hazard—Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3 ft (0.9m) away). Do not remove this tag.

5. Never place the Baby Unit(s) inside the baby’s crib or playpen. Never cover the Baby Unit(s) or Parent Viewer with anything such as a towel or a blanket.

6. Other electronic products may cause

interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless devices):

Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:

Pacemaker patients

• Should keep wireless devices at least six inches from the pacemaker.
• Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON.

WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices.

Electromagnetic fields (EMF)

This Leap Frog product complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user’s manual, the product is safe to be used based on scientific evidence available today

Download LeapFrog Baby Care app

Download and install the free LeapFrog Baby Care app to monitor your areas remotely.

|
---|---

App Compatibility

• AndroidTM 6.0 or later
• iOS 12 or later.

|
---|---

What’s Included

Connect, charge and power on the baby monitor

Connect the Baby Monitor

Charge the Parent Viewer battery

Notes:

• Before using the baby monitor for the first time, charge the Parent Viewer battery for 12 hours. When the Parent Viewer battery is fully charged, the battery icon becomes solid .
• The standby time varies depending on the Baby Unit sensitivity levels you set for Auto Wake-Up, your actual usage time and the age of the battery .

The battery icon on the screen indicates the battery status:

Battery Indicators

| Battery Status|

Action

---|---|---
The screen displays . The light flashes.| The battery has very little power left and may only be used for a short time.| Charge without interruption (about 30 minutes).
The battery icon becomes solid .| The battery is fully charged.| To keep the battery charged, connect it to AC power when not in use.

Power On or Off the Baby Monitor

1. Slide the On/Off switch to ON in order to power on your Baby Unit.
2. After the Parent Viewer is fully charged, press and hold until the welcome screen appears.
   

Note:

• The POWER LED Light is OFF by default.
  

Status Check

Once your Baby Unit and Parent Viewer are powered on, your Parent Viewer displays image from the Baby Unit, and the LINK LED light turns on.

Position the Baby Monitor

Note:

• To avoid interference from other electronic devices, place your baby monitor at least 3 feet (1 meter) away from devices such as wireless routers, microwaves, cell phones and computers.

Caution:

• The default volume of your Parent Viewer is level 3, and the maximum volume is level 5. If you experience a high-pitched screeching noise from your baby monitor while positioning:
  • Make sure your Baby Unit and Parent Viewer are more than 3 feet (1 meter) apart, OR
  • Lower the volume of your Parent Viewer.

Test the location for the Baby Unit

If you plan to install your Baby Unit in a designated location and use your home Wi-Fi network to connect your video monitor. You need to test which of the monitoring areas within your house have good Wi-Fi signal strength.

Tips:

• Adjust the distance or direction between your Baby Unit and the Wi-Fi router if needed.
• Depending on surroundings and obstructing factors that affect signal strength, such as distance and internal walls, you may experience reduced Wi-Fi signal.

Parent Viewer Overview

1. Link LED light
   • On when the Parent Viewer is linked to the Baby Unit.
   • Flashes when the link tothe Baby Unit is lost.

2. Battery LED light

3. 3-level sound indicator light

4. Night Mode quick set key
   • Select black-and-white or color night vision viewing mode.
   • Press to access night light brightness adjustment sub-menu.

5. Arrow Keys

6. Menu/ Select

7. Talk/ Return
   • Press and hold to talk to the Baby Unit.
   • While in a sub-menu, press to exit.

8. Microphone

9. VOL volume
   • Press to view the volume adjustment bar.

10. zoom

11. Power / LCD Off

12. Antenna

13. Power jack

14. RESET
    • Force reboot the Parent Viewer.

15. Stand

Baby Unit Overview

1. Light sensor

2. Camera

3. Infrared LEDs

4. Microphone

5. Night light

6. Night light control key
   • Press to turn the night light on or off.
   • Press and hold to adjust night light brightness level.

7. POWER LED Light

8. On / Off switch

9. Speaker

10. Antenna

11. Power jack

12. Wall mount holes

13. PAIR key
    • The Parent Viewer and Baby Unit(s) provided are already paired.

How the system works?

Direct mode

The Parent Viewer and the Baby Unit of your video monitor connect to each other in Direct mode by default, which allows you to stream live video right out of the box.

Wi-Fi Router mode

Wi-Fi Router mode uses your home Wi-Fi network to connect your video monitor. It enhances your local access by extending connection range.

With the LeapFrog Baby Care app, your Wi-Fi router (not included) also provides Internet connectivity to your baby monitor system, allowing you to control your Baby Unit wherever you are.

Protect your privacy and online security

LeapFrog cares about your privacy and peace of mind. That’s why we’ve put together a list of industry-recommended best practices to help keep your wireless connection private and your devices protected when online.

Ensure your wireless connection is secure.

• Before installing a device, ensure your router’s wireless signal is encrypted by selecting the “WPA2-PSK with AES” setting in your router’s wireless security menu.

Change default settings.

• Change your wireless router’s default wireless network name (SSID) to something unique.
• Change to a unique and strong password.

Keep your devices up to date.

• Download security patches from manufacturers as soon as they become available. This will ensure you always have the latest security updates.
• If the feature is available, enable automatic updates for future releases.

Disable Universal Plug and Play (UPnP) onyour router.

• UPnP enabled on a router can limit the effectiveness of your firewall by allowing other network devices to open inbound ports without any intervention or approval from you. A virus or other malware program could use this function to compromise security for the entire network.

Protect your privacy and online security (Con’t)

For more information on wireless connections and protecting your data, please review below:

1. Federal Communications Commission: Wireless Connections and Bluetooth Security Tips – www.fcc.gov/consumers/guides/how-protect-yourself-online.
2. U.S. Department of Homeland Security: Before You Connect a New Computer to the Internet – www.us-cert.gov/ncas/tips/ST15-003.
3. Federal Trade Commission: Using IP Cameras Safely – https://www.consumer.ftc.gov/articles/0382-using-ip-cameras-safely.
4. Wi-Fi Alliance: Discover Wi-Fi Security – http://www.wi-fi.org/discover-wi-fi/security

Adult supervision

• This baby monitor should be used as an aid and proper adult supervision is required.
• Do not place the baby unit inside the crib or playpen.
• As for children’s safety, touch or play with the baby monitor and all the accessories are not allowed. THIS IS NOT A TOY.

Disposal of Batteries and Product

The crossed-out wheelie bin symbols on products and batteries, or on their respective packaging, indicates they must not be disposed of in domestic waste as they contain substances that can be damaging to the environment and human health.

The chemical symbols Hg, Cd or Pb, where marked, indicate that the battery contains more than the specified value of mercury (Hg), cadmium (Cd) or lead (Pn) set out in Battery Directive (2006/66/EC).

The solid bar indicates that the product was placed on the market after 13th August, 2005.

Help protect the environment by disposing of your product or batteries responsibly.

Product Warranty

| PRODUCT WARRANTY

Thank you for choosing this quality product from VTech

---|---
Please contact the place of purchase.

Declaration of Conformity

This product is intended for use within Europe.

This equipment compiles with the essential requirements for the Radio Equipment and

Telecommunications Terminal Equipment Directive 2014/53/EU.

LeapFrog Enterprises, Inc., a subsidiary of VTech Holdings Limited hereby declares that this Video Monitor LF925HD is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.

The Declaration of Conformity for LF925HD is available at www.leapfrog- babycare.eu

Customer Support

| Find the answer to your questions. Get assisted at your own pace using our knowledge-rich full Online Manual, or contact Customer Support with your inquiries.
---|---
Scan the QR code to access our website or visit www.leapfrog- babycare.eu
Technology| Wi-Fi 2.4GHz 802.11 b/g/n
---|---
Channel| 13
Internet Connection| Minimum Requirement: 1.5 Mbps @ 720p or 2.5 Mbps @ 1080p upload bandwidth per Baby Unit
LCD| 5”(12.7cm)Color LCD (IPS 1280×720 pixels)
Nominal effective range| Actual operating range may vary according to environmental conditions at the time of use.
Power requirements| Parent Viewer: 3.7V 5000mAh Lithium-ion battery Baby Unit power adapter: Output: 5V DC @ 1.5A Parent Viewer power adapter: Output: 5V DC @ 2A

Credits:
The Background Noise sound file was created by Caroline Ford, and is used under the Creative Commons license. The Stream Noise sound file was created by Caroline Ford, and is used under the Creative Commons license. The Crickets At Night sound file was created by Mike Koenig, and is used under the Creative Commons license. The Heart Beat sound file was created by Zarabadeu, and is used under the Creative Commons license.

Importer: Snom Technology GmbH. Wittestraße 30G, 13509, Berlin (Germany) Manufacturer: VTech Telecommunications Ltd. 23/F., Tai Ping Industrial Centre, Block 1, 57 Ting Kok Road, Tai Po, Hong Kong

Specifications are subject to change without notice. © 2022 LeapFrog Enterprises, Inc., a subsidiary of VTech Holdings Limited. All rights reserved. 02/22 LF925HD_EU_QSG_V1.

References

• The domain name babycare.eu is for sale
• VTech Telecom Products European Official Site
• Smart Video-Babyphone | Video-Babyphone | Audio-Babyphone | LeapFrog
• Before You Connect a New Computer to the Internet | CISA
• Security | Wi-Fi Alliance
• How To Secure Your Home Security Cameras | Consumer Advice

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>