SW-MOTECH 10051479 SLC Side Carrier Instruction Manual

ANBAUANLEITUNG
mounting instructions, BC.HTA.08.866.20000
contiene
HTA.08.866.10000, HTA.08.866.11000
BC.HTA.00.402.101,00L, BC.HTA.00.402.10100R

ANBAUANLEITUNG / MOUNTING INSTRUCTIONS

Art.-Nr. / Item No.: HTA.08.866.10000 & HTA.08.866.11000
Revision: 00 . Datum/ Date: 07 – 2017  Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical understanding! For your own safety, SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/ or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behavior and/or stability of your vehicle.

GENERAL INFORMATION

Observe the country-specific regulations concerning vehicle registration/operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/ exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturer · specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with a medium-strength liquid thread locker. Torque specifications undefined by SW-MOTECH must be obtained from the the vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation makes sure that all parts and connections previously removed are properly replaced. Also, make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/ or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper
the fit of the product.

Step| NO.| Item No. / Description| Part| Quantity| N.m
---|---|---|---|---|---
1| | HTA.08.866.10000| SLC Side Carrier right| |
| 1| HTA.08.866.901.01| Side Carrier; Rechts| 1/1|
| 2| HTA.00.152.080| Guide Bolt| 3/3|
| 3| HTA.00.152.081| Lock Bolt| 1/1|
| 4| M6 x 20; DIN 6912| Hexagon Socket Screw, short head| 1/1| 7
| 5| M6 x 20; DIN 7991| Countersunk Screw; black| 2/2| 7
3| 6| M8 x 75; DIN 912| Hexagon Socket Screw; black| 1/1| 23
| 7| d 8.4; DIN 125| Washer; black| 1/1|
| 8| 018/0 10.5/h 30| Spacer| 1/1|
| 9| M8 x 35; DIN 912| Hexagon Socket Screw| 2/2| 23
| 10| 020/08.2/h3| Spacer| 2/2|
| 11| 025/d 8.4/h 4| Spacer| 2/2|

8.8

10.9

• All measurements in millimeters. • ” The second number indicates the total quantity of the part in the delivery. *** No torque specifications: Use the torque defined by the vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.
  

PARTS LIST

Step| NO.| Item No. / Description| Part| Quantity| N.m
---|---|---|---|---|---
1| | HTA.08.866.10000| SLC Side Carrier right| |
| 1| HTA.08.866.901.01| Side Carrier; Rechts| 1/1|
| 2| HTA.00.152.080| Guide Bolt| 3/3|
| 3| HTA.00.152.081| Lock Bolt| 1/1|
| 4| M6 x 20; DIN 6912| Hexagon Socket Screw, short head| 1/1| 7
| 5| M6 x 20; DIN 7991| Countersunk Screw; black| 2/2| 7
3| 6| M8 x 75; DIN 912| Hexagon Socket Screw; black| 1/1| 23
| 7| d 8.4; DIN 125| Washer; black| 1/1|
| 8| 018/0 10.5/h 30| Spacer| 1/1|
| 9| M8 x 35; DIN 912| Hexagon Socket Screw| 2/2| 23
| 10| 020/08.2/h3| Spacer| 2/2|
| 11| 025/d 8.4/h 4| Spacer| 2/2|

8.8

10.9

MOUNTING

![SW-MOTECH 10051479 SLC Side Carrier - fig 1](https://manuals.plus/wp- content/uploads/2022/08/SW-MOTECH-10051479-SLC-Side-Carrier-fig-1.jpg)|
---|---
NOTE: The mounting steps IN to (3.1 show the mounting of the left side carrier. Mount the right side carrier in the same way as on the left side of the vehicle. Attach the parts (2) to (5) to the side carrier (1), as shown in the drawing. ATTENTION: Use a liquid thread locker! Tighten the screws as specified in the parts list| Remove the passenger footrest and the shown plastic plug from the vehicle.

NOTE: If you want to mount the side carrier (1) with the SW-MOTECH ALU- RACK, the spacer (81 is not required. Mount the side carrier (1) with the Spacer of the ALU-RACK to the vehicle, as shown in the detailed drawing. Attach the side carrier (1) to the vehicle, as shown in the drawing. ATTENTION : Use a liquid thread locker! Once all parts are evenly positioned without excess tension, tighten the screws 161 and 191 with the manufacturer’s specified torque.

MOUNTING INSTRUCTIONS

Legend Gear Side Bag LC1/LC2

Thank you for choosing this premium product from SW-MOTECH. le; Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop. » www.sw- motech.com
Carefully follow all the directions given in the mounting instructions. Also, pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! Please keep the mounting instructions as a reference. SW-MOTECH assumes no liability for damages caused by improper fixation and handling.
This product was developed for vehicles in their original condition. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Installed accessories can change the driving behavior and/or stability of your vehicle.

GENERAL INFORMATION

Please observe any country-specific regulations concerning vehicle registration.
PREPARATION: Read the mounting instructions carefully and make sure that all parts are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Make sure to use only the appropriate tools. During installation have another person help you.
FUNCTION CHECK: This is a universal product. For this reason make sure BEFORE the first use, that the product can be fixed properly and used without problems with your vehicle type.
ATTENTION: All components of the product must not contact any hot or moving parts of the vehicle. All parts should also remain 5 cm away from hot parts of the vehicle and remain clear of the exhaust stream. After mounting, make sure there are no clearance issues while the suspension is both compressed and extended.
ATTENTION: Before riding and at each stop (every 200 km) check the proper fixation of the product! After fixation also makes sure that no moving parts are obstructed and the function of the vehicle is not hindered in any way. Lamps as taillight and turn signals must not be limited in their function. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions.

LOADING INFORMATION

ATTENTION: Riding with this product may affect the motorcycles driving and braking performance! Make sure weight is evenly distributed!
ATTENTION: Depending on the location of fixation, cornering and ground clearance can be reduced by using this product! Never store pointy or sharp- edged objects in the product, which could cause injury to persons or damage to the vehicle/product. Use a waterproof inner bag/rain cover to protect your luggage from moisture. Additionally protect sensitive luggage le.g., electronic equipment) from moisture with a plastic bag. l hate ‘t
ATTENTION: Maximum load: 5 kg / 11 lbs! The maximum vehicle Lel specified by the manufacturer must not be exceeded!
ATTENTION: Maximum speed with this product: 130km/h!

CARE

Clean the product periodically or after each trip, as dust and dirt have a worn effect and permanent stains can be prevented. Clean the product after riding in salty conditions, to avoid damage from salt.
First, remove dust and encrustations with a soft dry brush. Remove stubborn deposits with a soft cloth and warm soapy water.
Do NOT use strong cleaning agents, rough cleaning tools, or a high-pressure washer! Then rinse with clear water. Before re-use dry the product for at least 24 hours in the air (not in direct sunlight. We recommend impregnating the cotton textile surface of the product in regular intervals or after intensive cleaning with a commercial wax impregnation (e.g. from Fjoaraven). ATTENTION: Because the textile surface material is a natural fiber, it will experience color changes or fading when exposed to direct sunlight for extended periods of time and by environmental factors (e.g., SMOG, acid rain, etc.)! SW-MOTECH assumes no liability for this!
ATTENTION: Dirt on the product and vehicle has an abrasive effect and can damage surfaces, such as the paint. Make sure that all areas of the vehicle, which have contact with the product or parts of the product as straps, are protected with an adhesive protection film from scratches and abrasions. SW- MOTECH assumes no liability for paint damage and abrasions

|
---|---
Fasten the Velcro closure of the side bag Ilan b). Revert the reinforced opening of the side bag Ilan b) twice completely.| Fix the shown loops with the side-mounted hook buckles .
|
Tighten the straps of the hook buckle. Secure the opening of the side bag (1a/1b) with the shown strap.|  Place the three openings of the quick-release fastening system onto the locating bolts of the mounted SLC side carrier
|
Press the side bag Ilan b1 slightly downward, until it properly rests on the SLC side carrier. ATTENTION: Make sure that all three locating bolts engage at the same time! Pay attention to the clearly audible snap sound of the locking mechanism!| To release the side bag (1a/1b) simply press the shown slider of the locking mechanism downward

Copyright by
SW-MOTECH GmbH & Co.KG
SW-MOTECH GmbH & Co., KG Ernteweg 8/10 , 35282 Rauschenberg, Germany
Tel. / phone + 49 (0)6425 / 8168 – 050, Fax / fax + 49 (0)6425 / 8168 – 10, infofasw-motech.com , www.sw- motech.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>