PowerPac IF7850 Evaporative Air Cooler Instruction Manual
- June 9, 2024
- PowerPac
Table of Contents
PowerPac IF7850 Evaporative Air Cooler
PARTS & DESCRIPTION
Control Panel
(Status Light is illuminated for 30 seconds (and then dimmed) whenever a
button on the Control Panel or the Remote Control is pressed
WARNINGS
ATTENTION :
Read this booklet carefully as it contains important instructions for a safe
installation, use and maintenance.
Important instructions to be kept for future reference. The following basic
precautions should always be followed when using electrical appliances:
-
Read all instructions before using the appliance.
-
This appliance must be used only for the purpose it was expressly designed; any use NOT complying with the instructions contained in the manual is considered inappropriate and dangerous. The manufacturer is NOT responsible for possible damages caused by the inappropriate and/or unreasonable use.
-
This appliance is NOT suitable to be used in an explosive environment (in the presence of flammable substances such as gas, vapour, mist or dust, in atmospheric conditions when, after ignition, the combustion is spread in the air). Items containing these substances should never be placed in the appliance, and never be used to clean the appliance in order to avert the risk of fire or explosion.
-
The packing materials (plastic bags, expanded polystyrene, etc.) must be kept out of the reach of children or disabled persons since they represent potential sources of danger.
-
The installation/assembly of the appliance will be made in accordance with the indications of the manufacturer. A wrong procedure may cause damages to persons, animals or objects, for which the manufacturer cannot be considered responsible.
-
Before use, check the integrity of the appliance and power cable. In case you are not sure, contact a qualified person. If the power cable is damaged, it must be replaced by the manufacturer or its service agent or a qualified technician in order to avoid a shock hazard.
-
Before powering the appliance make sure the rating (voltage and frequency) corresponding to the grid and the socket is suitable for the plug of the appliance, and that the wall socket is properly grounded.
-
DO NOT power the appliance using multiple sockets. If possible, avoid the use of adapters and/or extension cables; if their use is absolutely necessary, use only materials in compliance with the current safety regulations and according to the electrical parameters of the adapters.
-
The appliance must NOT be switched on using external timers and/or other remote control appliances which are not specified in this manual.
-
Only use original components & accessories provided by the manufacturer. Any non-original components & accessories NOT recommended by the manufacturer
may cause injuries to persons or damage to the appliance. -
During use and storage, the appliance must be kept at a safe distance from heat sources (open flame, ovens, heaters, stoves, etc.) or any flammable and/or potentially explosive substances.
-
If you are using the appliance for the first time, you should:
-
Clean the exterior parts of the appliance with damp cloth moistened with warm water with a non-abrasive sponge. Take special care that the Control Panel found at the top of the appliance is kept dry.
-
Check that the Fan Grills and Fan Blade are NOT damaged.
-
Place and use the appliance on a horizontal, stable and dry surface. Damage may occur if the product is placed on an incline or decline.
-
After pulling out the Water Tank (bottom and back of appliance), add sufficient water into the Water Tank but DO NOT add beyond the maximum volume.
-
Push the Water Tank back into the appliance.
-
Insert the plug of the power cable directly into a standard AC socket. Be sure that the plug fits tightly into the socket.
-
Press the ON/OFF Button on the Control Panel or the Remote Control once to turn the appliance ON or OFF.
-
Press the SPEED Button on the Control Panel or the Remote Control to adjust wind speed from Low >>> Medium >>> High
-
Press the MOSQUITO Button on the Control Panel or the Remote Control once to enter the MOSQUITO Repellent mode. The appliance emits ultrasonic waves to repel mosquitoes. Press again to exit the MOSQUITO mode.
-
Press the COOL Button on the Control Panel or the Remote Control once to enter or exit the COOL mode.
-
Press the SWING Button on the Control Panel or the Remote Control once to keep the vertical front grill swinging from side to side continuously or to freeze the movement.
-
Press the ANION Button on the Control Panel or the Remote Control once to turn ON or to turn OFF the air purifier.
Make sure to remove any label or protective sheet which may prevent its proper functioning.
DO NOT: -
overload the Water Tank by filling it past the MAX volume indicated;
-
cover the appliance during functioning;
-
obstruct totally nor partially the air inlet & outlet;
-
insert objects or body parts through the air vents at the front of the appliance or inside the protection cover of the appliance during functioning;
-
place objects on top of the appliance;
-
attempt to force the fan blades to turn;
-
use the appliance near curtains or textiles;
-
use any of the following agents as a cleaner: gasoline, thinners, or benzene;
-
operate the appliance for more than 6 hours without turning it off for at least 30 minutes to let the appliance cool down for a total usage of 12 hours a day – failure to heed this warning may result in motor failure;
-
press the buttons on the Control Panel or the Remote Control too hard so as to avoid any damage;
-
leave the appliance unsupervised during operation.
-
-
Plug and unplug the power cable firmly holding it with dry hands. Always unplug the power cable to avoid overheating and avoid stretching it (DO NOT pull it, tug it or use it to drag the appliance to which is connected). Before unplugging the appliance, switch it off, using the proper command on the control panel.
-
During operation, DO NOT touch the appliance with wet body parts, and it is recommended to have between you and the standing surface, an isolating element (for example, wearing shoes with rubber soles).
-
DO NOT soak the appliance in water or other liquids, wash it under the tap, or let any liquid flow into the internal casing of the appliance to prevent electric shock. In case of accidental fall in water, DO NOT try to take it out, but first of all unplug immediately the power cable from the socket.
-
DO NOT operate the fan next to an open window while it is raining. Rainwater splashing onto the fan may cause an electric shock.
-
Place the appliance at a proper distance from objects or surrounding walls making sure that its functioning will not cause accidental damages. There should be at least 10 cm of free space from the back, left & right sides, and the top of the fan.
-
The appliance should NOT be placed on any surface or in the vicinity of objects which can be damaged by heat, such as carpets or plastics, while in operation or immediately after.
-
Avoid placing the power cable on abrasive or sharp surfaces or in positions where it can be damaged easily.
-
Always remember to unplug the power cable of the appliance if it is NOT used for a long period, before changing accessories, storing, cleaning or performing any maintenance operation.
-
Avoid carrying out operations which are NOT specified in this manual (such as disassembling and/or altering).
-
In case of malfunction or anomaly during the functioning, switch off the appliance immediately, turn off the power and check the cause of the anomaly, if possible, with the support of a qualified person.
-
DO NOT touch the inside of the fan while it is operating. The blades are rotating at very high speeds, which may lead to injury to your fingers and hands.
-
If smoke is observed coming out of the appliance, unplug the power cable immediately.
-
This appliance is a personal care device and is NOT intended for commercial use.
-
This appliance is intended to be used in households and similar applications, such as:
- Staff kitchen areas in shops, offices and other working environments;
- Dormitories;
- By clients in hotels, motels and other residential environments;
- Bed and breakfast type environment.
-
DO NOT use or store the appliance outdoors. Store and use the appliance only indoors, or in any case, protected from weathering such as rain, direct radiation of the sun and dust.
-
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall NOT play with the appliance. Cleaning and user maintenance shall NOT be made by children unless they are older than 8 and supervised. Keep the appliance and its power cable out of reach of children less than 8 years old.
-
Save these instructions.
HOW TO USE
Warning: The fan is fully assembled. DO NOT operate the fan with any of its parts disassembled. The entire assembled unit works as a single appliance. The fan must only operate in the upright position. Any other position will be hazardous.
-
Avoid using the appliance in a closed environment. The appliance should be used in an open and well-ventilated environment.
-
When the appliance operates under the COOL function, the Water Tank must be filled with water. Although the appliance can be used as an ordinary fan without using the COOL function, accidentally operating the appliance under the COOL function with an empty Water Tank may result in possible damage to the appliance. Thus, to be on the safe side, the Water Tank of the appliance should be filled with water prior to operation.
-
When moving the appliance, be aware that water can spill out of the Water Tank. Thus when moving an appreciable distance, it is recommended that all water be drained from the Water Tank prior to the move.
Draining the Water Tank -
The Water Tank should be drained and re-filled with fresh, clean water frequently. DO NOT fill the Water Tank with other liquids.
- Pull out the Water Tank found at the bottom and back of the appliance.
- Pull out the Drain Valve and wait until all water has flowed out of the Water Tank.
- Put the Drain Valve back in.
Filling the Water Tank
-
Water can be added to the Water tank by:
- Pulling out the Water Tank (bottom and back of the appliance), and using a hose or the Water Container provided (or any clean container) to fill up the Water
- Tank with water until the orange water level indicator reaches the top of the Water Level scale (above the minimum and below the maximum levels of the tank).
- Push the Water Tank back into the appliance and close the hatch.
-
What the Functions Buttons do:
- When the COOL mode is activated, the Water Pump in the Water Tank pumps water to saturate the Cooling at the back of the appliance. Air which flows through the Cooling Pad loses heat to the water and exits at a slightly lower temperature. Thus a decrease in temperature occurs; the exact decrease depends on the relative humidity and air temperature. If the button is pressed when the Speed is high, the fan speed will drop to its lowest speed for 30 seconds before resuming normal operations.
HOW TO CLEAN
- Press the Control Button on the Control Panel or the ON/OFF Button on the Remote Control to switch off the fan.
- Unplug the power cable holding it firmly with dry hands.
- Wait for the appliance to cool down completely.
- Clean the exterior parts of the fan thoroughly with damp cloth moistened with warm water & detergent with a non-abrasive sponge.
- DO NOT use metal scouring pads.
- DO NOT use any of the following agents as a cleaner: gasoline, thinners, or benzene.
- Never run water over the appliance as malfunctions may occur if water seeps inside the appliance. Take special care that the Control Panel found at the top of the fan is kept dry and prevent water from leaking into it.
- You may also use a vacuum cleaner to suck up dirt from the Air Inlet.
- Pull out the Water Tank at the bottom and back of the appliance.
- Pull out the Drain Valve and wait until all water has flowed out of the Water Tank.
- Unlock the Water Pump.
- Pull out the Water Pump.
- Remove the Water Tank from the appliance completely.
- Clean the Water Tank with damp cloth moistened with warm water & detergent with a non-abrasive sponge. DO NOT use metal scouring pads.
- Push the Water Tank back into the appliance.
- Put the Water Pump back into the Water Tank.
- Lock the Water Pump.
- Put the Drain Valve back in.
- Use a hose or the Water Container provided (or any clean container) to fill up the
- Water Tank with water until the orange water level indicator reaches the top of the Water Level scale (above the minimum and below the maximum levels of the tank).
- Push the Water Tank into the appliance fully and close the hatch.
- Remove the Back Shutter on the back of the appliance. The Back Dust Filter attached to the Back Shutter can be detached. Then remove the Back Cooling Pad.
- Clean the Dust Filters, Cooling Pads and Shutters under running water. Let the components air-dry before replacing them in their respective positions on the appliance. After cleaning it, remember to replace the in their original positions.
PROBLEM SOLVING
Fault symptom | Cause analysis | Troubleshooting |
---|---|---|
The appliance does not respond when any of the buttons are pressed. | The power | |
cable could be damaged. | Please stop use and contact customer service. |
AC fuse could be damaged or the circuit stops functioning to prevent
overload.| Replace the fuse or restart the unit. If problems persist, please
stop use and contact customer service.
Remote Control or Control Panel could be damaged.| Contact customer service to
replace the Remote Control or to repair the Control Panel.
Remote Control batteries have run out.| Replace the Remote Control batteries.
No air flows out of the appliance while the appliance is operating.| The motor
could be damaged.| Please stop use and contact customer service.
The wiring within the motor or appliance could have loosened.| Please stop use
and contact customer service.
Thermal protection inside the motor has been activated as appliance was used
for longer than 6 hours.| Please switch the appliance off, unplug from the
electric mains and wait for the appliance to cool down completely before
attempting to operate the appliance again. If the appliance still does not
operate normally, please stop use and contact customer service.
The appliance functions, but the air coming out is not cool enough.| The
Cooling Pad is dry or contains an insufficient amount of water due to either
insufficient amount of water in the Water Tank or that the Water Pump is not
functioning.| Clean the Water Tank and replace the water in the Water Tank.
Clean the Water Hose. Remove dirt from the Water Pump’s strainer. Check that
the Water Pump is functioning normally. If the Water Pump is not, please stop
use and contact customer service.
---|---|---
The Dust Filter and/or Cooling Pad are clogged with dust or dirt.| Clean or
replace the Dust Filters or Cooling Pads.
Excessive high relative humidity in the room due to environmental factors
(of which nothing can be done) or that the appliance has been turned on in
its current cycle that the room has been saturated with moisture (saturated
vapour pressure of water vapour is at maximum) so much so that the appliance
is unable to lower the temperature of the room.| Turn the COOL mode off to
avoid releasing more moisture into the room.
Water is spurting out from the air inlet together with air.| The Cooling Pad
has strayed out of position or that the Water Tank is clogged with debris.|
Place the Cooling Pad in the correct position.
Clean the Water Tank and replace the water in the Water Tank. Just in case
that debris has entered the system, clean the Water Hose and the Water Pump’s
strainer.
White sediments in the Water Tank.| The water in the Water Tank is saturated
with salt.| As water is continually removed from the Water Tank, various salts
are left behind, which in time become saturated and exceed their Solubility
Product values (Ksp). This is normal.
Clean the Water Tank and replace the water in the Water Tank. Clean the Water Hose.
---|---|---
Undesirable odour| The unit is placed in an| Clean the Cooling Pad or Water
emitted.| environment where| Tank and replace the water in
| undesirable odours are| the Water Tank.
| prevalent or that algae or|
| mould is growing on the|
| Cooling Pads or in the Water|
| Tank.|
The appliance is overheating. There are sparks coming from the outlet when the
appliance is plugged in.| This could be caused by a blockage of hair, dust or
some other obstruction in the Air Inlet.| Power off the dryer and unplug it
from the power source.
Use a soft bristle brush to gently remove any lint or hair present from both the Air Inlet and its cover.
| | If this does not fix the problem, please contact customer service.
ENVIRONMENTAL TIP
This device, along with all other electronic devices, should, when it is no longer capable of functioning, be disposed with the least possible environmental damage according to the local regulations in your area. In most cases you can discard the device at your local recycling center.
DISPOSAL: Do not dispose this device as unsorted municipal waste. Collection of such waste separately for special treatment is necessary.
WARRANTY
- The manufacturer provides warranty in accordance with the legislation of the customer’s own country of residence, with a minimum of 1 year, starting from the date on which the appliance is sold to the end user.
- The warranty covers defects in material and workmanship.
- The repairs under warranty may only be carried out by an authorised service centre.
- When making a claim under the warranty, the original bill of purchase (with purchase date clearly indicated) must be submitted.
- The warranty will not apply in cases of:
- normal wear and tear
- if the steps (as laid out in the section regarding Warnings) have not been observed e.g. overloading of the appliance, use of non-approved accessories
- if the appliance has not been properly maintained, if force has been used against it or if it has been damaged in any other way
- damage caused by non-observance of the user manual or non-compliance with the installation instructions
- errors or faults owing to defects in the distribution system
- if the appliance has been repaired or modified or changed in any way or by any person not properly authorised
SPECIFICATION
- MODEL: IF7850
- VOLTAGE: 220-240V ~ 50/60Hz
- WATTS(W): 65W
ABOUT COMPANY
- PowerPac Electrical Pte Ltd
- sales@powerpac.com.sg
- PowerPacSg
- www.powerpac.com.sg
- @PowerPac4
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>