NEXIGO Q500 P4 Gamepad Instruction Manual

NEXIGO Q500 P4 Gamepad

Please use it after reading the instructions carefully.

OVERVIEW

P4 connection method

1. After the P4 is powered on, connect the controller to the P4 with a USB cable.
2. Press the HOME button
3. After the connection is successful, pull oút the USB cable and switch the wireless mode automatically

A wireless connection iPhone/iPad/Android/PC

1. The controller side
   SHAREE holds down HOME for 3 seconds

2. Mobile terminal

3. Support mode is DualShock 4 wireless controller. (On Android, the device appears as a wireless controller.)

4. Supported games: Approved games are supported according to MFI. Examples: Mykra, Fortnite, Call of Duty, NBA 2K Mobile Arcade, etc. The original god corresponds to iOs14, notice.

5. IOS versions support versions 13/14/15 or later, and Android versions 9/10/11/12 or later. Please try to update to the latest version.

6. According to the game, after the connection, the game can not be linked without enabling the controller.
   Such as the original god. Please pay attention to.

Buttons can be programmed

Back button: Fn1, Fn2

Bbutton can be programmed:
Land Ranalogjoystick /up/down/left/right/L1/R1/L2/R2/L3/R3

On/Off programmable buttons

Since it is initial OFF, it cannot be set if it is not on)

Set up back buttons(illustrated with Fn1)

1. Long press Fn1for 2 seconds while pressing the Turbo key, and the LED flashes.
2. After pressing one or several buttons at your preferred speed (up to 60 seconds/24 buttons), press the Fn 1again to end.

Clear & interrupt Programmed Back Buttons(illustrated with Fn1)

1. Press turbo while long press Fn1for 2s,after LED flashes,press En1again to clearthe functions set up on Fn1.
2. To interrupt/stop the operation of Fn1,press other back buttons (Fn1/ Fn2).
3. Note that press the front buttons is not able to stop the operation.

Auto-play Programmed Back Buttons(illustrated with Fn1)

1. After Fn1 is set up,press Turbo and Fnito auto-play the functions set up on Fn1.
2. Press turbo and Fn1again to turn off auto-play.

Please note:

1. Functions programmed on back buttons will not the cleared even if power is turned off
2. Press SHARE and back button for over 5 seconds to reset all back buttons.
3. IF the back button is turned off(refer to On/Off programmed button),the programmable function cannot be set up.
4. Only one of the back buttons will work while multiple back buttons are pressed at the same time

Special Turbo Set up

Press turbo multiple times on the same button can cause different effects.
(see below figuer for details)
The buttons which can set up Turbo functions:
D button (up and down around)/ button/X button/ button / button/L1 button/L2 button/R1 button/R2 button|

Turbo Setting(illustrated with L1)

Set Up Turbo Frequency
This controller has three levels ofTurbo frequencies:8/15/25 times/sec.

Press Turbo and switch the right joystick up/down to adjust Turbo frequencies.

1. Press turbo+Switch up to increase the firing frequency from 15times/sec to 25 times/sec
2. Press turbo+switch down to decrease the firing frequency from 15times/sec to 8 times/sec
3. The default frequencyis 15 times/sec

Please note:

1. Switch up twice to increase the frequency from 8 times/sec to 25 times/sec and vice versa
2. LED flashes for 2 seconds when the frequency is changed
3. The change in frequency will be saved even if power is turned off

TURBO functions
Turbo function button: /L2/R2

Turn on (e.g. )

Press and TURBO button ate the sanme time

Turn off

Press and TURBO button at the same time

Note: Turbo functionality is cleared if the controller is turned off.

Charging

1. The LED light flashes when the battery is low.
2. Use USB cable to charge, while charging the LED light to keep yellow
3. LED light goes off after charging completes.
   Note: Low battery power can cause problems with inefticient
   Connection buttons, so make sure the controller is fully charged in case this is possible

Attention

1. Press the home button to start the controller.And you can hold down the home button for 10 seconds to turn the controller off.
2. When the battery is nearly exhausted, the LED light will flash. Please charge the controller.
3. When the controller is charged with an ordinary charger, the LED lamp flashes in orange.When charging is finished, it will turn off. If you charge during use, When charging completes, it becomes light.
4. If the connection cannot be completed within 1 minute, the controller will be automatically turned off

Factory data reset

Use a niddle to press the reset button in the hole on the back of the Controler and turn off the controller to finish reset (make sure the Controller is turned on while pressing the reset button in the hole)

Product specification

1. dimension: L158″ width 100* height 50 mm
2. Weight: 212g
3. USB input voltage: DC5V/500mA
4. Construction guarantee: DC 3.7V/80mA
5. Maximum current: 200mA
6. Continuous use time: 8 hours
7. Charging time: 3 o ‘clock or so
8. Effective distance: <1OM
9. Battery capacity: 650mHA

Package content

• P4 controller x 1
• USB data cable x1
• Operation instruction X1

Matters needing attention

• Never give small parts to children under 3 years of age.
• Please do not decompose, repair or alter.
• For maintenance, please use a soft cloth. In addition, please do not use aniline, diluent and other drugs.
• The lithium-ion battery in this product is designed and manufactured with safety in mind and can be safely used. However, if the decomposition of this product, damage to the built-in battery, excessive strong impact, the built-in battery electrode short circuit, accompanied by sharp heating, has occurred.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>