StarTech Under Desk Cable Tray Organizer User Guide

June 9, 2024
StarTech

StarTech Under Desk Cable Tray Organizer

StarTech-Under-Desk-Cable-Tray-Organizer-fig-1

Product Diagram (UDCMTRAY)

StarTech-Under-Desk-Cable-Tray-Organizer-fig-2

  Components Function
1 Cable Tray Organizer •          Organize and hide Cables

•          Hide a Power Strip

2

| Mounting Holes/ Screws| •          Mount the Cable Tray Organizer underneath a Desk

•     #12 Phillips® Head Screws

3

| ****


Screwdriver Access Holes

| •          Cutouts that allow a Phillips Head Screwdriver or a Phillips Head Drill Bit to pass through the bottom of the Cable Tray Organizer

Note: A long Phillips Head Screwdriver or a Drill Bit Extension may be required to fasten the Mounting Screws.

Package Contents

  • Cable Management Tray x 1
  • Mounting Screw x 2
  • Quick-Start Guide x 1

Requirements

For the latest requirements, please visit www.startech.com/UDCMTRAY.

  • 3 Phillips Head Screwdriver or a Power Drill with a Phillips Head Bit x 1

  • Power Drill with a Drill Bit x 1
  • Pencil x 1
  • (Optional) Drill Bit Extension x 1

Installation

Note: It is easier to complete the following installation steps with two people.

  1. Hold the Cable Tray Organizer in the desired location under the Desk, with the Mounting Holes resting against the underside of the Desk.

  2. Mark the location of the Mounting Holes using a Pencil.

  3. Use a Power Drill with an appropriately sized Drill Bit to drill Pilot Holes into the locations of the Mounting Holes.
    Notes: The Pilot Holes should be the same depth as the length of the Mounting Screws. A small piece of tape can be placed on the Drill Bit to mark the proper depth of the Pilot Holes. The Drill Bit size will be determined by the wood used to construct the Desk. Consult a professional if you are unable to determine the proper Drill Bit size.

  4. Insert the Mounting Screws through the Mounting Holes and into the Desk. (Figure 1)

  5. Fasten the Screws into the Desk using a Phillips Head Screwdriver or a Power Drill with a Phillips Head Bit.

StarTech-Under-Desk-Cable-Tray-Organizer-fig-3

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

  • This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of thirdparty companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
  • PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.

Warranty Information

  • This product is backed by a two-year warranty.
  • For further information on product warranty terms and conditions, please refer to www.startech.com/warranty

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.

Safety Measures
If product has an exposed circuit board, do not touch the product under power.

ABOUT COMPANY

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

StarTech User Manuals

Related Manuals