ASROCK 90GA2RZZ Challenger D 8GB at Rich Electronics Installation Guide
- June 9, 2024
- ASRock
Table of Contents
ASROCK 90GA2RZZ Challenger D 8GB at Rich Electronics
Hardware Installation
-
Turn off your PC and unplug the power cord.
-
Open the case and locate the graphics card slot.
-
Remove the corresponding slot covers on the back of the PC.
-
Insert the card into the slot until it is fully seated.
-
Secure the card to the case with screws.
-
If your graphics card requires an external power source, connect the power supply to the card.
-
Close the case. Plug the display cable into the card.
-
Plug in the power cord and turn on the PC.
Driver Installation
- Insert the support CD into your optical drive.
- Follow the on-screen instructions to complete driver installation.
The graphics card photos in this document are for reference only, and may be
different from the actual product you purchased.
Depending on your motherboard, you may need to open the latch on the slot to
remove the graphics card. Please refer to the motherboard documentation for
the proper procedure.
If this graphics card does not come with the driver and the utilities, please
download them from ASRock website (https://www.asrock.com).
Version 1.1
Published October 2022
Copyright©2022 ASRock INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.
Products and corporate names appearing in this documentation may or may not be
registered trademarks or copyrights of their respective companies, and are
used only for identification or explanation and to the owners’ benefit, without
intent to infringe.
Disclaimer:
Specifications and information contained in this documentation are furnished
for informational use only and subject to change without notice, and should
not be constructed as a commitment by ASRock. ASRock assumes no responsibility
for any errors or omissions that may appear in this documentation. With
respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited
to the implied warranties or conditions of merchantability or fitness for a
particular purpose.
In no event shall ASRock, its directors, officers, employees, or agents be
liable for any indirect, special, incidental, or consequential damages
(including damages for loss of profits, loss of business, loss of data,
interruption of business and the like), even if ASRock has been advised of the
possibility of such damages arising from any defect or error in the
documentation or product.
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
The terms HDMI® and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
CALIFORNIA, USA ONLY
The Lithium battery adopted on this motherboard contains Perchlorate, a toxic
substance controlled in Perchlorate Best Management Practices (BMP)
regulations passed by the California Legislature. When you discard the Lithium
battery in California, USA, please follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see
www.dtsc.ca.gov/hazardouswaste/perchlorate”
AUSTRALIA ONLY
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure
and compensation for any other reasonably foreseeable loss or damage caused by
our goods. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a
major failure. If you require assistance please call ASRock Tel :
+886-2-28965588 ext.123 (Standard International call charges apply)
ASRock INC. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of related UKCA Directives. Full text of UKCA declaration of conformity is available at: http://www.asrock.com
ASRock INC. hereby declares that this device is in compliance with the
essential requirements and other relevant provisions of related Directives.
Full text of EU declaration of conformity is available at:
http://www.asrock.com
ASRock follows the green design concept to design and manufacture our
products, and makes sure that each stage of the product life cycle of ASRock
product is in line with global environmental regulations. In addition, ASRock
disclose the relevant information based on regulation requirements. Please
refer to https://www.asrock.com/general/about.asp?cat=Responsibility for
information disclosure based on regulation requirements ASRock is complied
with.
DO NOT throw the motherboard in municipal waste. This product has been
designed to enable proper reuse of parts and recycling. This symbol of the
crossed out wheeled bin indicates that the product
(electrical and electronic equipment) should not be placed in municipal waste.
Check local regulations for disposal of electronic products.
DO NOT throw the motherboard in municipal waste. This product has been
designed to enable proper reuse of parts and recycling. This symbol of the
crossed out wheeled bin indicates that the product
(electrical and electronic equipment) should not be placed in municipal waste.
Check local regulations for disposal of electronic products.
References
- ASRock > Support Request Form
- ASRock
- ASRock > Corporate Social Responsibility
- dtsc.ca.gov/hazardouswaste/perchlorate
- ASRock