KESNOS PD220B Home Dehumidifier User Manual

PD220B Home Dehumidifier User Manual

FOR CUSTOMERS

Thank you for purchasing our dehumidifier.

Kesnos wishes that our products and services can bring convenience to your work and life. We highly recommend that you keep the manual for reference if you encounter unexpected events using the unit.

Please read the manual carefully to ensure proper use of the dehumidifier. Our dehumidifiers are widely used in family bedrooms, bathrooms, base ments, offices and storage rooms, etc.

The dehumidifiers from provide quick and efficient operation to Kesnos reduce room’s humidity and bring you a healthy and comfortable life.

TO ACCESS CUSTOMER SUPPORT FASTER

If there is any problem of the product, please contact Kesnos Customer Service at with your Purchase Order ID to help you support@kesnos.com address the problem more effectively

BEFORE FIRST USE

To prevent any internal damage, it is very important to keep the unit (like this one) upright throughout its journey.

Please leave it standing as the picture shown below and outside the box for 24 HOURS before plugging it in.

Statement

The graphics and functions provided in this manual may not be the same as the actual product. Please always refer to the actual product.
The model of the machine on the manual is for reference only, please check the corresponding content and operate the machine based on the actual product.
The right to interpret the relevant terms belongs to the company.

SAFETY INSTRUCTIONS

Safety Notes:
For your safety, please read the manual carefully and keep the manual for future reference. Please use this product according to the instructions of installation and operation of this manual.

• Before cleaning the dehumidifier, turn off the power and unplug it from the power outlet.
• Please do not place the machine near heat or flammable dangerous goods.
• Do not insert your fingers or sticks into the air inlet or outlet.
• Always keep the machine on even surfaces, avoid placing the machineonuneven or sloping ground.
• Do not spray water, insecticides or flammable liquids on the unit.
• This machine should not be placed in a confined and narrow space.
• When the power cord is damaged, it must be replaced by a technician approved by the company.
• When using the dry clothes function, the clothes should be kept at least 15.7inches away from the air outlet to prevent water from entering the machine and damage the machine.
• The machine power wiring must be in accordance with national wiring rules, and, power line should be connected to the reliable external grounding line.
• Model specification of safety tube: 3.15A
• This dehumidifier is designed to operate in a working environment between 41°F (5℃) and 95°F (35℃).
• When using the dehumidifier, other objects surrounding the machine need to be kept at least a distance of 7.9 inches (20cm) as shown in the picture on the right:

PARTS DESCRIPTION

Front

Rear

CONTROL INTERFACE

Control Panel

Timer Button
Press to initiate the auto-start or auto-stop feature.

Child Lock
Press the button and hold for 2 seconds, the control panel will be locked.

Lighting Button
Control the LED panel’s light on/off

Power Button
Press to turn the dehumidifier on/off.

Setting Button
Control the humidity setting up/down

Speed Button
Control the fan speed

OPERATION INSTRUCTIONS

Setting

Setting Humidity
The humidity level can be set within a range of 30%RH to 80%RH in 5% increments

• When it starts to work, it will first automatically detect and show the room’s humidity.
  In dehumidification mode (other modes are invalid), press the “SETTING” button, you can change the humidity selection in 5% increments, ” 52 ” will flash and show the setting humidity.

• When the humidity level is higher or drops to the level you have set, the dehumidifier will automatically begin to work or stop.

• When the humidity level is set at 30%RH, the dehumidifier will be work at  continuous dehumidifying mode.

After no operation for 5s, ” 52 ” will display the actual room humidity.

When the room humidity level is higher than your setting value, the dehumidifier will automatically start working; when the humidity drops to what you desire, the dehumidifier will automatically stop and the “DEHUMIDIFY” icon on the screen will flash, indicating the wet control status.

When the humidity level is set at 30%RH, the dehumidifier will work at continuous dehumidifying mode.

Timer Setting

This TIMER setting function is designed for you to set a time to turn off or turn on the machine, automatically by the timer.

1. Press the “TIMER” button to select the timer by 1-hour increment. You can set the timer up to 24 hours. It will start to do the countdown when you start the timer.
2. Press and hold the “TIMER” button for several seconds to make the selection of the timer faster.
3. If the time is set to 00, this is called the invalid time.
4. If you set the timer successfully, the timer indicator “ ****” will be on. The LED screen will show the remaining time if you press the “TIMER” button, and display the current humidity automatically after a few seconds.

Speed Button

Control the fan speed. Press to select either FAST or SLOW fan speed.
FAST fan speed will result in quicker moisture removal. Set the speed FAST for maximum moisture removal. When the humidity has been reduced and quiet operation is more preferred, set the fan speed back to SLOW.

Light Function Setting

1. In the power on status, press the “LIGHTING” button to turn on or turn off the backlight;
2. When light funtion is powered on, except the “POWER” button and the “LIGHTING” indicators is on, other backlight indicators will be off.

LOCK(2S)

When the unit is turned on, press the “LOCK” button “ ” and hold on for 2 seconds, the control panel will be locked together with the other buttons.To unlock the control panel, press and hold the “LOCK” button “ ” again for 2 seconds.

Power Off Memory Function

• The device will automatically restore the working status after powered on.
• If the device is turned on and a power interruption occurred, after starting the unit again, it will keep the previous parameters of setup.
• lf the device is turned off and power interruption occurred,the device will still be in a power off status when turned on.

Overflow Protection

When the water tank is full of water, the machine will turn off automatically.
The indicator light “ ” will flash. After you empty the water from the tank, the indicator light “ ” will turn off. The machine will start to work.

Caution:
Water tank must place in right position, otherwise will cause the waterfull alarm.

Auto Defrost Feature

When the dehumidifier is running at a lower temperature, the system will automatically determine whether there is a presence of frost. lf any frost exists, it will defrost automatically.

Defrost Action
The fan runs at high wind speed when the compressor stops.

Display Status Description

• When the device is currently powered on, before any operation, only the “POWER” indicator will be on indicating the device is in “Standby” status.
• Timing indicator “ ****“:If the timer is set up properly, the indicator light will be on.
• Lighting indicator “ ****“：When use the lighting function, this indicator will be on, otherwise, it will be off. Auto Defrost Feature When the dehumidifier is running at a lower temperature, the system will automatically determine whether there is a presence of frost. lf any frost exists, it will defrost automatically. 3. Display Status Description
• High-speed indicator “ “：if you set this unit to high speed fan mode, this indicator will light up.
• Low-speed indicator “ “：If you set this unit to low speed fan mode, this indicator will light up.
• Dehumidification indicator “ “：When the machine starts to dehumidify, this indicator will light up.
• Water full indicator “ “：When the water tank is full, this indicator will flash to alarm.
• Lock indicator “ ****“: This indicator will light up when the control panel is successfully locked, otherwise it won’t be on.
• When the dehumidifier works normally, ” 52 ” will display the current 52 humidity.

Instructions for Drying Clothes

The dehumidifier can be used for drying clothes in rainy weather.

Step 1.
Hang the washed clothes in a small space such as cloakroom, bathroom, or storage room.
Note: Keep away the unit from the water drip of the washed clothes.

Step 2.
Open the dehumidifier and set the humidity level at 30%RH. It is best if you let the air outlet of the dehumidifier to blow air to the clothes directly.

1. The drying effect will vary from the thickness of clothes, the number of clothes and the size of the drying space. Theoretically, the effect will be better when clothes are few, thin and space is small.
2. The drying process would take 3-8 hours, and we suggest that continuous drainage mode is would be suitable when drying clothes.

Fault & Processing Methods

Humidity always shows “25% RH” — but there is a log difference fromthe actual humidity.| Humidity sensor failure?| Set the humidity to 30%RH.the dehumidifier can still continue to work, and can be used normally.
Repair and replace the humidity sensor.
Humidity always shows ‘99% RH’ — but there is a big difference from the actual humidity.| Water on the surface of humidity sensor?| The dehumidifier is not affected and can continue to work, and can be used normally.
Please let the dehumidifier keep working for a period of time. after the water on the surface of humidity sensor is removed, it will return to normal.
Repair and replace the humidity sensor.

If the malfunction is still present, please don’t hesitate to contact Kesnos Customer Service email: support@kensons.com for help.

Note: Before starting the machine, please ensure that the air outlet has been opened, otherwise the machine will overheat. Do not pull out the power cord directly to stop the machine.

Empty the Tank or Bucket
Two ways are available to remove the collected water.

Use the Water Tank

When the water tank is already full, the Full Tank Alert indicator will light up, the dehumidifier will automatically shut down until the tank has been emptied and placed back to the unit.

Ways to Empty the Water Tank

1. Pull the water tank out from the bottom with your hand
   

2. Invert the water tank to empty the waterb
   

3. Put the water tank back in place, the water full indicator will go out
   

Note:

• Do not remove the float from the water tank. If the float in the water tank is removed, the sensor may not be able to determine the water level stored in the tank properly that may lead to water overflow leak from the water tank.
• If the water tank is dirty, just use cold water or warm water to clean it. Do not use detergent, steel wool, chemically treated dust cloth, gasoline, benzene, thinner or other solvents. Otherwise, it may damage the water tank and cause it to leak.
• When placing back the water tank, use your hands to press the tank back in its place. If the water tank is not placed properly, sensors or protections from water overflow may not operate as expected.

Continuous Drainage

Remove the power supply, use a knife or pliers and other tools to remove the plastic cover of the continuous drainage port and insert the water hose into the port. Connect the power supply to start the operation. The outlet of the water hose should be lower than the continuous drainage port by more than 3.9 inches, and can not be bent.

(Note: The diameter of continuous drainage port is 0.63 inches.)

1. Remove the plastic cover
   

2. Insert the water hose into the continuous drainage port.

CLEANING AND MAINTENANCE

WARNING:
Turn the dehumidifier off and remove the plug from the wall outlet before cleaning.

A- Cleaning the dehumidifier body
Please use only a soft and a bit wet textile or cloth to clean it.

B- Cleaning filter

• Pull out the filter.
• Clean the filter: Use a vacuum cleaner to gently remove the dust from the surface of the filter. If the filter is very dirty, wipe it with warm water and a mild detergent and dry it completely.
• Slowly insert the filter back into the fuselage.
  

C-Dehumidifier storage

When you want to store the dehumidifier because you don’t use it for a long time. Please pay attention to the following steps:

1. Empty the water in the water tank.
2. Roll up the power cord and tie it up.
3. Clean the filter.
4. Place the machine in a cool and dry environment.

TROUBLESHOOTING

Check the information below for troubleshooting steps. It will save you time to resolve issues that may happen with the unit. The list includes most of the common cases, but not the results of defective units, crafts or materials in the unit. If all troubleshooting steps have been exhausted and the issue is still occurring, please feel free to reach out to Kesnos
Customer Service to get further assistance.

unit’s plug is inserted properly into the power outlet.
ls the Full Tank indicator blinking? (The tank is full or in a wrong position. )| Empty the water in the water tank and then reposition the tank.
Is the room temperature above 95°F (35°C)or below 41°F (5°C).| This product does not apply to over hot or cold environment, the machine will automatically enter the protection mode. It is a normal phenomenon.
Is the room temperature between 41°F(5°C) and 68°F(20°C) ?| When running under lower ambient temperature, the machine will automatically defrost, which is a normal phenomenon. It will restart dehumification again until the defrosting process finished.
The dehumidifier is in the defrosting process.| It is normal the compressor ceases while defrosting process. Wait until the process finished, it will restart dehumidification again.
Is the room humidity lower or reaching the preset humidity level? (When the room humidity has reached the preset level, the dehumidifier will enter Standby Mode and the indicator on LCD will flash. )| Please set the humidity decrease by 5% than the room humidity or set the humidity to 30%.
This is to prevent the frequent start of the machine. Does the machine stop working just now?| Please wait for more than 3 minutes.
Room humidity is low.| The dehumidifier is designed to work in the humidity range of 30%-80%. Above or below this range, it will not work.
Dehumidifier does not dry the air as it should| The air filter is dirty.| Clean the air filter.
Is the air inlet or air outlet obstructed?| Remove the obstruction from the air inlet or outlet.
The dehumidifier size is too small for application.| Increase the quantity of dehumidifier. Or change a higher capacity dehumidifier.
Poor air circulation.| Please leave about 7.9inch(20cm) around the product.
Did not allow enough time to remove the moisture.| Allow enough time to remove the moisture.When first installed, allow at least 3-4 days to maintain the desired RH.
The room has not been sealed properly.| Check that all doors, windows and other openings are securely closed.
The air filter is clogged.| Wash the filter.
Room temperature is too low, or below 41℉ (5℃): The machine will not work or undergo poor dehumifying efficiency in low temperature.| Please wait until the temperature rises to above 5℃ or higher.
The dehumidifier makes loud noise when operating| The dehumidifier is not positioned levelly.| Move the machine to a horizontal position.
Is there blocking around the air inlet?The air filter is clogged.| Clean up the dirt or lint on the air outlet and intake.
Is the filter installed correctly?| Please check whether the packing bag of the filter had been removed and the filter has been installed correctly.
Dehumidifier operates continuously| Check if the dehumidifier is in Continuous Mode.| Do Not set the humidity too low. Typically, 40-50% are good for use.
Room humidity is too high.| Change humidity setting. Or change to a higher capacity dehumidifier.
Doors and windows are open.| Ensure that all doors, windows and other openings are closed.
Overflow of water on floor| The float of water tank has been stuck.| Move the float and let it swing freely.
The magnet on the float has come off.| Put the magnet in right position.
Hose to connector or hose connection may be loose.| Connect the hose with the drainage port tightly.
The water tank has not been installed properly.| Re-install the water tank properly.

If the dehumidifier is still not working properly as expected and the troubleshooting steps or solutions above may not resolve the issue.

Please unplug the power and shut down the dehumidifier, then contact Kesnos Customer Service at . support@kensons.com

SPECIAL NOTES

1. When using, please do not put the machine at the soft and uneven ground, avoid vibration and movement.

2. Do not insert thin rods and hard objects into the fuselage to avoid malfunction and danger.

3. When using, please keep the machine away from heating furnace, electric kettle and other heat sources.

4. When using, make sure doors and windows are closed to get the best humidity removal effect.

5. Please do not put objects around the body. If the ventilation is blocked, the dehumidification effect will be affected.

6. . If do not use the product for a long time, please unplug the power cord.

7. When cleaning the dehumidifier fuselage, please use wet cloth or textile to wipe the unit’s surface gently, do not splash water on the unit directly.

8. Please do not put any object on the dehumidifier.

9. Please clean the filter every two weeks (do not use hot water above 104 F, gasoline toluene)

10. When on continuous drainage, make sure the drainage pipe is placed horizontally on the ground. Avoid the pipe to be on uneven surface or in an arch position.

11. After cleaning the filter, do not dry the unit under direct sunlight to avoid filter deformation.

12. Before moving and carrying . the machine, please first pour out the water in the tank.

TECHNICAL PARAMETERS

WARNING:
This product can expose you to chemicals including Styrene and its compounds, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more Information go to: www.P65Warnings.ca.gov

WARRANTY AND CONTACT US

Warranty

Kesnos offers a 12-month warranty to all of our products together with the original proof of purchase when a defect occured, including those newly purchased and unused, from Kesnos or through an authorized reseller, wholly or substantially, or as a result of faulty manufacturing parts, or workmanship during the Warranty Period.

The warranty does not apply if damage is caused by other factors, including but without limitation of:

(a) Normal wear and tear;
(b) Abuse, mishandling, accident or failure to follow operating instructions;
(c) Exposure to liquid or infiltration of foreign particles;
(d) Servicing or modification of the product other than by Kesnos.

There are our general terms for the warranty service, but we always encourage our customers to contact us if any issues, regardless of warranty terms. If you are experiencing an issue with Kesnos product, you can reach out to us at support@kesnos.com, we will dedicate our efforts to resolve it for you

Extend Your Warranty by 1Year

Register your product at yiww kecnos com to extend your 1-year warranty by an additional year.
***** Please fill out all required fields and inlcude your Order ID, Date of Purchased if applicable.

Customer Support

If you have any questions or concerns about your product, please feel free to contact our expert support team. Kesnos customer service is here to help.

Kesnos Office
13211, Spring Street Baldwin Park, CA. US
Email: support@kesnos.com
Live Chat: www.kesnos.com

Support Hours
24 Hours available
Please have your Order Number ready before contacting customer support.

For FAQs and more information please visit:
www.kesnos.com

@Kesnos
@Kesnos
@Kesnos
@Kesnos

(Scan the QR Code for Live Chat)

We are expecting to see our products fulfill your life and hear your voice. Your satisfaction means a lot to us. Please tag us if you share a snap on your social media.

www.kesnos.com

References

• Kesnos | Humidity Removal Appliances | Free Shipping

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>