AENO AP4 Air Purifier User Manual
- June 4, 2024
- AENO
Table of Contents
AP4 Air Purifier
User Manual
| 
---|---
| 
The AENO Air Purifier is designed to disinfect and clean indoor air from allergens, pollen, fungal spores, dust particles, smoke, animal hair, and unpleasant odors.
Specifications
Supply voltage: 12 V, 2 A. Rated power: 24W. Power adapter input voltage: 100 240VAC, 50-60Hz. Air flow rate: 150m /h. Noise level: Up to 40dB (at a distance of 1m). Coverage: Up to 25m 3 . Indoor air purification time: 2-3 hours. Net weight: 2.1kg. Dimensions: Ø205mm × 385mm.
Package Contents
AENO Air Purifier (See Figure a), power adapter, HEPA filter, quick start guide, warranty card.
Limitations and Warnings
ATTENTION! The device is equipped with a built-in UV lamp. It is not allowed
to disassemble the device and turn it on when disassembled, because it may be
very harmful to the eyes.
Make sure the purifier is unplugged before maintenance. Do not immerse the
purifier in water or any other liquid. Do not use aggressive and flammable
chlorine- or alcohol-containing agents to clean the purifier. Use the device
as described in this Quick Start Guide and the complete User Manual only.
Failure to follow the instructions may result in fire and other hazardous
situations, as well as injuries. Do not use the device if it is damaged or
cracked. Do not install the device outdoors or near sources of water,
including humidifiers. Do not expose the device to direct sunlight, moisture,
or vibration. Do not drop, throw, disassemble the device, or try to repair it
on your own. Do not lay the power cable near radiators, stoves, or heaters. Do
not use cleaning agents or detergents to clean the device. Do not dispose of
the device with unsorted urban waste, because this will be harmful for the
environment. For more information on proper disposal, please contact your
local waste collection and disposal company. Keep children away from the
device. There is a risk of serious injury and electric shock. This device is
intended for use by adults only. Warnings, precautions, and instructions
contained herein may not contain every possible hazardous situation. Please
use common sense when operating the device.
Initial Setup
Before the operation, you should remove the packaging from the HEPA filter. To
do this, please turn the purifier upside down and remove its cover by turning
it counterclockwise (See Figure b). Then, remove the HEPA filter from the
device body using the fabric strips (See Figure c), remove the filter
packaging, and insert the filter back into the device body. Tighten the cover
by turning it clockwise (See Figure d). After that, you should connect the air
purifier to the source of power (mains socket) using the power adapter
included in the package of supply. The power connector of the adapter must be
inserted into the power port in the device casing, while the plug of the
adapter – into the mains socket. ATTENTION! Never use a non-original power
adapter to connect to and power on the device, as this may damage the
purifier.
Button Panel Control
The purifier will be switched to the Standby Mode upon connection to the main
socket using the power adapter. The control panel of the device contains the
following 6 LED buttons (See Figure e):
- The POWER button is used to switch the purifier from Standby Mode to Operation Mode, as well as to turn off the purifier, or turn on the anion filter.
- SLEEP, SPEED MID, and SPEED HIGH buttons are used to switch the fan speed of the purifier in the following way: Sleep – quiet mode, Speed Mid – medium rotation speed of the fan, Speed High – high rotation speed of the fan;
- FILTER button that is blinking every time the filter shall be replaced (an audible signal will also be emitted. You may stop it by pressing this button again);
- UV-C button is used to turn on the UV diode intended for air disinfection.
Maintenance
The HEPA filter shall be cleaned on a regular basis, but never rinsed up with
water or used after the end of service life. Please dry the HEPA filter
regularly in the sun. Do not remove dust from the HEPA filter with a vacuum
cleaner or a water jet. The HEPA filter shall be replaced every 2,200 hours of
operation (i.e. every 3-6 months). To remove dust from the HEPA filter, you
shall remove it from the purifier casing. Use a soft cloth with a neutral
(non-aggressive) detergent to remove dust or large pieces of dirt from the
surface of the HEPA filter. The HEPA filter shall be installed back in the
purifier casing only after it gets dried. If the device is not planned to be
used for a long time, please store it covered with a dustproof bag in a dry,
cool, and well-ventilated area. It is also recommended to power on the device
from time to time for at least a few minutes in order to keep it in good
working condition. ATTENTION! Do not allow water to enter the purifier.
Troubleshooting
- The purifier does not turn on. Make sure that the purifier is plugged into the mains socket, that there is no power supply failure, as well as that the circuit breaker is on, that the fuses are intact, and that the filter change LED is blinking red.
- The device makes a loud noise. Make sure that nothing is stuck in the fan, and that the purifier is not tilted. If the noise is still too loud, try to reduce the fan speed using the Speed Mid or the Sleep button. Also, use Sleep Mode to operate the purifier at night.
- Unpleasant odor coming from the purifier. If the device emits a plastic smell during the first few hours of operation, this is deemed to be normal. However, the device may also emit an unpleasant odor when the filter is clogged. In this case, the filter must be cleaned or replaced. If you smell burning, unplug the purifier immediately. Then, contact our Support Dept or the Seller of the device for assistance.
- The filter change LED is blinking after the filter was replaced or cleaned. Click on the Filter button to restart the filter replacement timer, and the LED indicator will be turned off.
ATTENTION! If your problem persists, please contact your local supplier or the service center for support. Please do not disassemble the device or try to repair it on your own.
Recycling information
These symbols indicate that you must follow the Waste Electrical and
Electronic Equipment (WEEE) and Waste Battery and Battery Regulations when
disposing of the device, its batteries and accumulators, and its electrical
and electronic accessories. According to the rules, this equipment must be
disposed of separately at the end of its service life.
Do not dispose of the device, its batteries, and accumulators, or its
electrical and electronic accessories together with unsorted municipal waste,
as this will harm the environment. To dispose of this equipment, it must be
returned to the point of sale or turned into a local recycling facility. You
should contact your local household waste disposal service for details. The
warranty period and service life shall be 2 years from the date of purchase of
the device.
The warranty period and service life shall be 2 years as from the date of
purchase of the device. Manufacturer: ASBISc Enterprises PLC, 43 Kolonakiou
Street, Diamond Court, Ayios Athanasios, 4103 Limassol, Cyprus. Made in China.
For current information and details on the device description and
specification, as well as connection process, certificates, warranty, and
quality issues, see relevant Installation and Operation Manuals available for
downloading at aeno.com/documents.
All trademarks and names herein are the property of their respective owners.
GET MORE
aeno.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>