AENO TB1 ATB0001 Table Blender User Manual
- June 9, 2024
- AENO
Table of Contents
AENO TB1 ATB0001 Table Blender
OVERVIEW
WARNING
AENO TB1 electric blender is designed for chopping food, making smoothies, purees, drinks and other products.
Specifications
- Supply voltage: 220–240 V (AC)
- Frequency: 50/60 Hz
- Power: 800.0 W. Bowl
- Capacity: 1.75 L
- Measuring cup capacity: 80 ml
- Dimensions (L×W×H): 230 mm × 200 mm × 420 mm
- Weight: 4.7 kg
- Power cord length: 1 m
Package Contents
AENO TB1 blender, measuring cup, brush, steaming container, quick start guide, warranty card.
Limitations and Warnings
Children and persons with disabilities may use the device only under the supervision of adults experienced in its use. Keep the device out of the reach of children. During the operation of the device the surface of its bowl heats up. Do not touch it. Do not touch the device housing while it is operating. Do not disassemble or repair the blender on your own. Do not wash the bowl base with the electrical contacts and the clutch shaft with water. Place the blender only on a firm and stable surface. The distance from the operating device to other objects should be at least 15 centimeters. Do not store the blender cup in the refrigerator: short circuit of electrical contacts may occur due to condensation. Do not touch the blender blade.
WARNING! The min product level in the blender is 750ml. Do not exceed the max level for hot liquids (1200ml) and cold liquids (1500ml), it may cause overflow.
Do not open the lid of the blender cup while the blender is in operation. If you hear an intermittent sound of the blade turning when chopping food, this is normal. If you lift the bowl or open the lid of the blender while it is running, the protection will be triggered, and the motor will stop. Do not add sugar, plant stems or legumes (beans, peas, chickpeas, lentils) to the bowl, as the blade can jam, and it can cause damage to the device. To clean the blender blade (6) use the brush (14) . Before plugging in, make sure that the bowl is securely seated on the blender base and that the bowl lid is closed.
Preparing for operation
Wash the blender bowl (4) , the large lid (2) and the small lid (2) with warm soapy water and wipe it dry before the first use and each subsequent use.
WARNING! Never allow water to get to the bottom of the blender bowl base
(7). Short circuit of electrical contacts will occur and the device will
break down.
Place the bowl (3) on the blender housing (11) (See picture d ).
The bowl connector (5) must fit into the groove of the blender body
(10) . The motor shaft connector (9) must fit into the blade shaft
connector on the bottom of the bowl base (7) . The rubber compensators
(8) must fit into the recesses of the bowl base.
NOTE. If the bowl can not be installed on the blender housing, remove it from the base and twist the motor shaft connector (9) in the blender housing (11) by hand half a turn in either direction.
Operating the device
Place food in the bowl (4) . Then place the large lid (2) on the bowl
and turn it clockwise until the grooves on the large lid align with the
protrusions on the bowl (3) (See figure b). After that insert the small
cap (1) into the large cap (2) and turn it clockwise (See picture c).
To open the large and small lids turn them counterclockwise.
NOTE. The device will immediately stop working if you open the large lid. If you need to add food or spices while the blender is running, you can open the small lid to do so. Use the measuring cup (15) to dose spices and other products. You can find recipes of various dishes in the full instructions at Plug the device into a power outlet. Power control mode will turn on. Press the “ON/OFF” button to switch to standby mode. Select one of the eight blender programs by pressing the “FUNCTION” button. Then press the “Start/Stop” button (if you do not press the button within 30 seconds, the blender will go into standby mode). After that the selected program will start. When the process is finished, press the “ON/OFF” button and unplug the blender.
NOTE. The maximum continuous operation time is 5 cycles. In case of longer use, engine will be automaticly blocked. To resume work, you must disconnect the device from the power supply, remove the bowl and wait for no longer then 10 minutes. After this time, the device will be ready for use again. You can also turn on the blender in delayed start mode. To do this in standby mode you must first set the desired time before the program starts. To do this, first press the “PRESET TIME” button. Then use the “TIME+” and “TIME-” buttons to set the time required before the device starts. Each press of the Increase Time and Decrease Time button changes the time until the blender starts by 10 minutes. Then select the desired program with the “Program Selection” button and then press the “Start/Stop” button. The blender will start itself after a set period of time, work the selected program, and then go into standby mode.
NOTE. If you set the wrong time before the blender starts, you can cancel
the setting with the “START/STOP” button. The manual mode allows you to set
the duration of operation and rotation speed of the blade by yourself. To do
this, press the “MANUAL” button in standby mode and then use the “SPEED+” and
“SPEED-” buttons to set the desired speed. Then use buttons “TIME+” and
“TIME-” to set the required operating time of the device in minutes and
seconds. Then press the “START/STOP” button.
The self-cleaning mode helps to clean the blade from stuck pieces of food. To
do this, you need to remove food from the blender, pour 500ml of warm water
with a little dishwashing detergent into the blender and press the “CLEANING”
button. The blade will rotate as long as you hold down the button. When the
cleaning is finished, rinse the blender bowl with warm running water.
Device mode indication table (See figure e).
Troubleshooting
- The smell of burning plastic or rubber. Possible causes: the device motor is inside the housing under strong rubber materials to reduce noise and vibration. The first few starts the parts of the device will be hot and emit an unpleasant odor. Later on, the smell will disappear. Solution: It is recommended to install the blender in a well-ventilated room.
The products are not well chopped
- Possible causes: low mains voltage; too much or too little food in the bowl; not enough water in the bowl. Solution: plug the device into an outlet with a supply voltage of at least 220V, use a voltage regulator; remove excess food from the bowl or add water to it.
The liquid pours over the edge of the blender bowl
- Possible causes: too much liquid. Solution: make sure that the amount of liquid does not exceed the maximum level specified in the instructions.
Errors E1 and E2
- Possible causes: large lid and/or blender cup is installed incorrectly, with misalignment. Solution: remove the large lid and/or blender bowl and reinstall them again.
Error E3
- Possible causes: no liquid and/or food in the bowl, temperature sensors turn off the device due to overheating. Solution: add liquid or food to the bowl.
The blender heats up, the blade does not rotate
causes: short circuit. Solution: contact the service center.
WARNING! If your problem persists, please contact your local supplier or the service center for support. Please do not disassemble the device or try to repair it on your own.
Recycling information
These symbol indicate that you must follow the Waste Electrical and Electronic
Equipment (WEEE) and Waste Battery and Battery Regulations when disposing of
the device, its batteries and accumulators, and its electrical and electronic
accessories. According to the rules, this equipment must be disposed of
separately at the end of its service life.
Do not dispose of the device, its batteries and accumulators, or its
electrical and electronic accessories together with unsorted municipal waste,
as this will harm the environment. To dispose of this equipment, it must be
returned to the point of sale or turned in to a local recycling facility. You
should contact your local household waste disposal service for details SBISc
reserves the right to modify the device and to make edits and changes to this
document without prior notice to users. The warranty period and service life
shall be 2 years as from the date of purchase of the device. Manufacturer:
ASBISc Enterprises PLC, Iapetou, 1, Agios Athanasios, 4101 Limassol, Cyprus.
Made in China. For current information and details on the device description
and specification, as well as connection process, certificates, warranty, and
quality issues, see relevant Installation and Operation Manuals available for
downloading at aeno.com/documents. All trademarks
and names herein are the property of their respective owners.
References
- Documents | AENO in Europe
- Paramètres manuels - Перевод на русский - примеры французский | Reverso Context
- réduction - Перевод на русский - примеры французский | Reverso Context
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>