ZALMAN NPS10X Optima II RGB Fan User Manual
- June 9, 2024
- ZALMAN
Table of Contents
NPS10X Optima II RGB Fan
User Manual
Intel Socket LGA
2011 V3/2011/1366/1156/1155/1151/1150/775 CPUs
AMD Socket FM2+/FM2/FM1/AM3+/AM3/AM2+/AM2
CPU & APUs
To ensure safe and easy installation,
Please read the following precautions.
www.ZALMAN.com
Precautions
-
This cooler must be used with a 120mm fan.
-
Avoid inserting objects or hands into the fan while it is in operation to prevent product damage and injuries.
-
Do not ingest the Thermal Grease, and avoid its contact with skin and eyes.
If contact is made with skin, wash off with water. If ingested or irritation persists, seek medical attention. -
To prevent possible injuries, gloves must be worn while handling this product.
-
Excessive force exerted on the fan may cause damage to the fan and/or system.
-
Use and keep product away from reach of children.
-
Check the components list and condition of the product before installation.
If any problem is found, contact the retailer to obtain a replacement. -
During transportation of the system, the cooler must be removed. Zalman is not responsible for any damages that occur during the transport of a system.
-
Product design and specifications may be revised to improve quality and performance.
Specifications
| Model Spec. | CNPS1OX Optima (2011) |
|---|---|
| Material | Pure Aluminum & Copper |
| Weight | 630 g |
| Dimensions | 132(L) X 85(W) X 152(H)rmi |
| Fan | Bearing Type |
| RPM | 1,000 – 1,700rpm ±10% |
| Noise Level | 17.0 – 28.0dBA ±10% |
The mal Grease
[ZM-STG2M]| Contents| 1g
Temperature
Range| -40-C – +150-C ( -40 – +302°F)
Components
1) Common Components
2) Intel Components
– Socket LGA 2011 V3/2011/1366/1156 /1155/1151/1150/775
– Stand off 
3) AMD Components
Socket FM2+/FM2/FM1/AM3+/AM3/ AM2+/AM2
Installation Requirements
-
Space Requirements
The cooler’s installation requires an unobstructed space of 85mm(width), 132mm(length), and 152mm(height), with the CPU as a central reference point.
Please check if components such as ODDs and PSU protrude into the required space. -
Air Guide Removal
Air guides on enclosures must be removed before the cooler’s installation since they protrude into the cooler’s required space.
-
Cooler Orientation
As shown in the diagram below, it is recommended that the cooler be installed so that air flows from the cooler toward the enclosure’s rear exhaust fan to be released.
- Recommended cooler orientation may differ according to the motherboard model.
4. CPU and RAM interference check
Any RAM with a height taller than 44mm (1.75 ) will have interference with the CPU cooler. Please check the height of your RAM modules prior to installation.
Installation
A. LGA Intel Socket Installation
Lastly, fasten the four screws to secure the clips (Please go to Page 8 for
further instructions)
① – ⓐ Intel Socket 2011 V3 / 2011 User
Partially unscrew the four bolts located on the base of the CPU cooler. Then,
insert the Intel Clips between the base and the heatpipe cover, with the clips
bent away from the heatsink.
① – ⓑ Intel Socket 1366 / 1156 / 1155 / 1151 / 1150 / 775 User
Partially unscrew the four bolts located on the base of the CPU cooler. Then,
insert the Intel Clips between the base and the heatpipe cover, with the clips
bent away from the heatsink.
② Install the Bolts to the Backplate according to the socket type and secure
them with Side Caps.
※ Backplate is not needed for LGA 2011 V3 / 2011 sockets.
③ – ⓐ Socket 1366/1156/1155/1151/1150 Installation
Peel off one side of the Double-sided Tape and attach it to the center of the
Backplate with the sticky side facing down. Then, peel off the top cover.
※ Socket 1366/1156/1155/1151/1150 Installation does not require the Loading
Block.
③ – ⓑ Socket 775 Installation
Peel off the Loading Block cover and attach it to the Backplate with the
sticky side facing the center of the Backplate.
Peel off one side of the Double-sided Tape and attach it with the sticky side facing the Loading block. Then, peel off the top cover.
Caution
Please make note of the orientation of the Loading Block’s Installation.
④ – ⓐ Socket 1366 / 1156 / 1155 / 1151 / 1150 / 775 User
④ – ⓑ
Socket 2011 V3 / 2011 User
Fasten the four Stand-offs to the motherboard. Backplate is not needed.
⑤ Apply thermal grease just enough to thinly cover the CPU surface, then fasten the Bolts to isntall the cooler.
⑥ Latch the Fan Fixing Clips to the notches located on the sides of the
heatsink.
Note: It is often easier to latch the Fan Fixing Clips one at a time.
⑦ Position the fan as low as possible.
⑧ Connect the cooler’s 4-pin connector to the motherboard’s CPU Fan header.
Caution Please make sure that PWM Control Mode is activated in the motherboard’s BIOS settings.
B. AMD Socket Installation
① Partially unscrew the four bolts located on the base of the CPU cooler.
Then, insert the AMD Clips between the base and the heatpipe cover, with the
clips bent away from the heatsink.
② Install Bolts to the Backplate according to the Socket Type and secure with Side Caps.
③ Peel off the Loading Block cover and attach it to the Backplate with the sticky side facing the center of the Backplate.
Peel off one side of the Double-sided Tape and attach it with the sticky side facing the Loading block. Then, peel off the top cover.
Caution
Please note that the sticky side of the Loading Block serves to attach the
Loading Block to the backplate.
④
Dismantle the CPU cooler retention bracket on the motherboard by unscrewing
the four bolts located at each corner (method may vary; consult the
motherboard manual for details). Be sure to keep the retention bracket so the
stock CPU cooler can be used as a backup.
⑤ Attach the Backplate assembly to the back side of the motherboard by
aligning the Nuts to the motherboard mounting holes.
If you were unsuccessful at first attempt, you may continue with the
installation without the Double-sided Tape as it is not a necessary component.
⑥ Apply thermal grease just enough to thinly cover the CPU surface, then fasten the Bolts to isntall the cooler.
⑦ Latch the Fan Fixing Clips to the notches located on the sides of the
heatsink.
Note: It is often easier to latch the Fan Fixing Clips one at a time.
⑧ Position the fan as low as possible.
Lowering the fan helps to cool the components on the motherboard.
⑨ Connect the cooler’s 4-pin connector to the motherboard’s CPU Fan header.
Caution Please make sure that PWM Control Mode is activated in the motherboard’s BIOS settings.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>