HYUNDAI HHA492101 Smart IP Camera User Manual

June 9, 2024
HYUNDAI

HYUNDAI HHA492101 Smart IP Camera User Manual
HYUNDAI HHA492101 Smart IP Camera

Introduction

Thank you for purchasing the Smart Infrared Camera. Please read this user manual carefully to fully understand the usage of the camera. Keep the manual for future reference since it contains important information.

RESET

To reset the camera, press the reset button on top, next to the SD card slot. Using a paperclip or toothpick will help. Hold the button approximately 3 seconds until a “Dong-dong-dong” sound is heard.

During the resetting of the camera will turn around until you hear a 3-tone sound, this indicates that the camera has completed the reset.

The camera is now ready to (re)connect when the blue LED is slowly blinking.

Connect with HYUNDAI Home app

To control the camera you can use the HYUNDAI Home APP on your phone or tablet. Scan the QR Code to download the APP: HYUNDAI Home. If you can’t scan the QR code find the app “HYUNDAI Home” in the app store on your device. Create an account to start using the APP. If you already have an existing account, enter your login details to continue.

NOTE: SET UP YOUR ROUTER
This device only supports 2.4GHz frequency band router, does not support 5GHz frequency band routers, please set the relevant parameters of the router before Wi Fi configuration, Wi Fi passwords do not include special characters such as ~!@#$%^&*().

When the device is configured in WiFi, the mobile phone and device are as close as to the router, which can speed up the configuration of the device.

Setting up the camera using EZ mode

Create an account to start using the app. Once set up, optionally create a room for the device you are adding
Setting up the camera

  1. Navigate to “Security & Video surveillance” and select “Smart Camera (Wi-Fi)
  2. Make sure the device LED is blinking slowly, confirm and proceed to next step.
  3. In the top-right of the screen select the mode and pick “EZ Mode”.
  4. The app will then present you a loading screen where it negotiates settings with the camera. This should take no longer than a minute. Once done, the camera will show up in your device overview, and you can use it, optionally you can add it to a room.

Setting up the camera using QR code

Create an account to start using the app. Once set up, optionally create a room for the device you are adding.

  1. Navigate to “Security & Video surveillance” and select “Smart Camera (Wi-Fi)
  2. Make sure the device LED is blinking slowly, confirm and proceed to next step.
  3. Navigate to “Security & Video surveillance” and select “Smart Camera (Wi-Fi).
  4. Make sure the device LED is blinking slowly, confirm and proceed to next step.
  5. If your phone is connected to your Wi-Fi (2.4Ghz) The SSID and password should be visible. If password is not visible, please connect to your Wi-Fi, make sure the frequency of your network is 2.4Ghz and manually fill in the password. Once network name and password are confirmed, proceed to the next step. (Password cannot contain these characters ~!@#$%^&*() )
  6. Read the instructions on this page and proceed to the next step.
  7. Hold the QR code that shows up in front of the camera lens. Make sure you hold it still at about 20 cm distance. The camera needs about 15-20 seconds to read the QR code. Once the camera has read the QR code it will sound “Dong- dingdong”.
  8. The app will then present you a loading screen where it starts connecting to and setting up the camera. This should take no longer than a minute.

Once done, the camera will show up in your device overview, and you can use it, optionally you can add it to a room.

CAMERA FUNCTIONS

  1. Setting & Management
  2. Wi-Fi signal strength
  3. Sound switch
  4. SD/HD
  5. Full screen
  6. Screenshot
  7. Voice chat
  8. Record live view
  9. Playback of video
  10. PTZ control (The camera can be rotated to give you a different spective. You can move it in 4 directions to capture any corner you want to view)
  11. Motion detection

FAQ

Q: Fail to add device during net-pairing?

A: Please make sure the mobile phone and device are connected to 2.4GHz router. Make sure the correct Wi-Fi password is entered.

Q: Still fail to add device after re-scanning?

A: It is recommended to restart the device or power off the device, and try again

Q: The device does not show a video preview?

A: Check for weak Wi-Fi signal. You can place the camera close to the router. If it still doesn’t work, reset the device, remove it from the app, and add it again.

Q: Why is the device is still on the list after resetting the device?

A: The device reset only resets the camera’s network configuration and cannot change the configuration of the app. You must log in the app to delete the camera from the list.

Q: How to connect the camera to another router?

A: First log in the App to delete and reset the device, and configure the device again through the App.

Q: Why can the device not identify an SD card?

A: It is recommended to insert and remove the SD card after powering off the device. Check if the SD card is functional and formatted as FAT32.

Q: The device is online and has an alarm event, but the mobile phone cannot receive the information?

A: First confirm that the app allows notification in the settings of your mobile phone. Under normal circumstances, when an anomaly is detected, a message will appear in the notification bar of your mobile phone. You should set a notification sound or vibration in your mobile phone.

When viewing real-time video in the app, you cannot receive alarm of the cameral being viewed. The device defaults the camera being viewed indicating that the user is focusing on the video being monitored, and there is no need for an alarm.

NOTE: The application has to be allowed to run in the background on your device. Additional power saving options for the app, or system wide power saving should be disabled. If not, you may not receive notifications from the app.

SPECIFICATIONS

  • Form Factor Pan Tilt Camera
  • Product Colour White
  • Materials ABS
  • Viewing angle 75°
  • Sensor Type 2MP 1/3” CMOS
  • Resolution 1920*1080
  • Night Vision 8~10m
  • Working Indicator Yes
  • Mic Yes
  • Speaker Yes
  • TF Card Support max 128GB
  • Horizontal angle 355°
  • Vertical angle 90°
  • Standard IEEE 802.11 b/g/n 2.4GHz
  • Power Supply DC 5V 1A
  • Two-Way Talk Yes
  • Video Format H.265
  • IR turned ON: Enable night vision view, turn on infrared,
  • IR turned OFF: Disable the night vision view, turn off infrared, the ICR remains in daily view mode
  • Android Android 8.0 above
  • IOS IOS 9.X-10.X above Detection Sensitivity 0-3 grades, default grade 2, high / middle / low
  • On line visitor Max 5 users online simultaneously Type of Alarm Support push notifications, alarm timing, motion detection alarms, and sound detection alarms
  • Mobile APP remote control Yes
  • Communication Protocol WIFI
  • Move tracking Yes
  • Remote & monitoring Yes
  • Power failure memory Yes
  • Pairing Scan QR Code / WiFi EZ
  • Micro USB Cable & Screw Kit Yes, included
  • Power adapter DC 5V 1A

© 2022 The Investment Company Europe B.V.
PATENT PENDING
The artwork and design of this package are protected by European copyright law and may not be reproduced, distributed, displayed, published or used for any purpose without prior written permission. It is not permitted to alter, or reproduce any trademarks or copyright notice from this package. NL / EN – www.alleenonline.nl – BE / FR – www.alleenonline.be

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals