LNC A04846W4 30-in 4-Light Matte Black and Gold LED Modern-Contemporary Vanity Light Instruction Manual
- June 9, 2024
- LNC
Table of Contents
- LNC A04846W4 30-in 4-Light Matte Black and Gold LED Modern-Contemporary
- Item Number: A04846W4
- IMAGE FOR FINISHED PRODUCT:
- ASSEMBLY & INSTALLATION INSTRUCTIONS:
- 1. Carefully remove the fixture from the carton and check that all parts
- Before you start the installation, NEVER attempt any work without
- 3. Make assembly
- ** _ORDERING PARTS
- CLEANING
- Read More About This Manual & Download PDF:
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
LNC A04846W4 30-in 4-Light Matte Black and Gold LED Modern-Contemporary
Vanity Light Instruction Manual
Item Number: A04846W4
WARNING (To reduce the risk of fire, electric shock, or personal injury):
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at a later
- Before you start, NEVER attempt any work without shutting off the electricity until the work is
» Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “ OFF ” position.
» Place the wall switch in the “ OFF ” position.
- Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before
- Make sure the voltage you are using is 120V. The maximum wattage is 60W per
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the
- When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED Before starting assembly and installation please prepare the
needed
(NOT INCLUDED): tools as below picture
ACCESSORIES ENCLOSED:
(A) Mounting screw (2)
(B) Plastic wire connector (3)
PARTS INCLUDING:
(C) Green ground screw (1)
(D) Mounting plate (1)
(E) Back plate (1)
(F) Knob nut (2)
(G) Socket (4)
(H) Lampshade (4)
(I) Socket ring (4)
ASSEMBLY & INSTALLATION INSTRUCTIONS:
1. Carefully remove the fixture from the carton and check that all parts
and accessories are included as shown in the above illustration.
- Turn off power
Before you start the installation, NEVER attempt any work without
shutting off the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “ OFF ” position.
» Place the wall switch in the “ OFF ” position.
3. Make assembly
Step A1 » Step A2 »
Step A3 » Unscrew knob nuts (F) from back plate (E), then set them
aside for later installation.
Carefully pass the supply wires from the outlet box through mounting plate
(D). Secure mounting plate (D) to the outlet box with mounting screws (A).
Make wire connections Connect wires as below wires connection shown. PLEASE
NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND
WIRES.
Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
NOTE: back plate (E) should be snug against the wall with knob nuts (F).
If not, remove back plate (E), adjust the threaded length of pre-assembled
mounting screws on mounting plate assembly (D):
- Unscrew the pre-assembled hex nuts.
- Screw the pre-assembled mounting screws in or out of mounting plate (D).
- When the secure length is achieved, tighten the pre-assembled hex nuts and back to Step A4.
Step A5 » 1) Remove socket rings (I) from sockets (G), and carefully place
lampshades (H) on sockets (G), then secure them with socket rings (I).
2) Install bulbs (Not included) (Please do not exceed the maximum wattage
recommended on the socket.)
4. Check everything is installed properly, then you could turn on the light.
Enjoy!
** _ORDERING PARTS
_**
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>