MUNBYN P44S Label Printer User Manual

MUNBYN P44S Label Printer User Manual

Product Introduction

Thank you for choosing our thermal printer. Our product is capable with Windows, Mac, and Linux. Before using the printer, please take a few minutes to read this manual. It will guide you to set up the printer to best fit your needs.

What’s in the Box

When you receive the package, open, and check the items in it.

• Printer
• Adapter
• Quick tips
• USB Cable
• Power Cord
• Labels
• User Manual

Product Overview

_Figure 1-2 P44S Overview Diagram

_ Figure 3 P44S Rear Diagram

Quick Printer Connection

Figure 1-4 Connection Diagram

1. Ensure the switch is OFF
2. Connect the power cable to the printer
3. Plug in the power cord
4. Connect the USE cable to the printer
5. Connect the USE cable to the PC
6. Turn the power ON

Label Setup

Automatic Label Recognition: Open the top cover button, load no less than 4 consecutive labels into the printer, and close the top cover. After the paper feeds stably, press and hold the feeder button until hearing one “beep”, and the printer will automatically recognize the label.

Function Button

1| Feeder Button| | Press the button: Pull out one label.
---|---|---|---
Press and hold the button until hearing one ‘beep’: Automatically label identification.
Press and hold the button until hearing two ‘beeps’: Print the self-test label.
Press and hold the button until hearing three ‘beeps’: Activate the voice.
Press and hold the button until hearing five ‘beeps’: Reset the printer.
2| Printer Status
Light| Green| Ready to print or printing.
Red – Blinking
(Every Is)| The cover is not closed.
Red-Blinking
(Every 2s)| Label paper is not identified.
Green and Red – Alternating| The printer head is overheated.
3| Wi-Fi/Bluetooth
Connection Status
Light| Blue| The printer’s Bluetooth is connected.
White| The printer’s Wi-Fi is connected.
4| Sv.I.,f| | Power ON/OFF.
5| Top Cover Button| | Open the top cover.

Voice Command

Voice
Command| Execute the Result
---|---
Hi MUNBYN (Pronunciation
: / I mAnbin)| The printer responds loudly “I’m here”, and the printer’s voice wakes up (if there is no command within the 30s, the printer will sleep and say “I’m leaving. Call me next time”).
Prim test page| The printer responds loudly “Print test page” and prints the self-test page.
Learn label| The printer responds with the “Learn label” and automatically identifies the loaded label.
Take one label| The printer responds with “Take one label” and pulls out one label.
Printer reset| The printer responds with “Printer reset” and reset.
Turn off voice| The printer responds with “Turn off voice” and the voice function is off.

Note:

1. The voice will be activated automatically out loud with “welcome to the MUNBYN printer” after the machine is powered on; The printer top cover is open, automatically out loud with “cover is open”; No label loading in the printer will automatically out loud with “out of paper”.
2. After the voice function is off, press the feeder button until you hear three ‘ beeps to reactivate the voice.

Application Installation

Search Munbyn Print on Google Play or App Store to get the app or scan the QR code to download and install the application.

Figure 2-1 Search App

Figure 2-2 Google Play

Figure 2-3 App Store

Note: After opening the app, select Mims the app to locate permission (Android only) and use the phone’s Bluetooth permission.

Window/Mac/Linux Printer Installation Instruction

Note: To use the P44S printer on a PC, please install this printer driver in advance.

1. Get the latest driver from this link:
2. If your system is updated, please reinstall the driver to ensure that the printer can be used normally.

Before Installing

1. To connect the printer, refer to section 1.3 for a quick printer connection.
2. Place the thermal label paper into the printer and power it on. For paper loading, refer to section 1,4,

Windows USB Driver Installation

1. Double-click Munbyn-Windows-Driver-Latest-Witi-v1.1.1.
   
   Figure 3-1  Window Printer Driver Installation Package

2. The computer pops up a prompt to check the printer is connected, click OK.
   
   Figure 3-2 Window Printer Driver install Interface

3. Select the USB port for installation, and then click Next.
   
   Figure 3-3 Select USB Port for Installation

4. Select Next
   
   Figure 3-4 Windows Printer Driver Install Interface

5. Click Install, wait for about 3s, and the setup is finished.
   
   Figure 3-5 Windows Printer Driver Install Interface

6. The “Open Help Document” automatically checked, which is a P&4S FAQs document, Then click “Finish” to exit the setup and the printer is ready to use.
   
   Figure 3-6 Windows Printer Driver Install Interface

7. Print a test page to verify the driver has been set up successfully as per the following steps.

Figure 3-7 Print Test Page

**Window Setting

_Figure 3-8 Print Test Page

_ _Figure 3-9 Print Test Page

Figure 3-10 Print Test Page

_Mac Driver Installation**

1. Double-click Munbyn-Mac-Driverev1.1.demg.

Figure 3-11 Mac Printer Driver Installation Package

2. Chose the Open and Install Driver, then double  clickMunbynPrinter_v1.1.1_signed.pkg.

Figure 3-12 Mac Printer Driver Install Interface

3. Follow the prompts to complete the installation as shown in the figure below.

** _Figure 3-13 Mae Printer Driver Install Interface

Figure 3-14 Mac Printer Driver Install Interface

Figure 3-15 Mac Printer Driver Install Interface

Figure 3-16 Mac Printer Driver Install Interface_**

Linux Driver Installation

1. Right-click the munbyn-ubuntu driver folder, then select Open in Terminal

Figure 3-17 Open in Terminal

2.  Enter the installation command: sudo sh Munbyn_Driver_Ubuntu.run, then press the Enter key on the keyboard,
   
   MUNBYN P44S Label Printer User Manual

3. Enter the password of the computer and then press the Enter key on the keyboard to finish the installation,
   
   Figure 3-19 Enter the Password

Windows Printer Settings

Note: To use the P44S printer on a PC, please install this printer driver in advance.

1. Get the latest driver from this link
2. If your system is updated, please reinstall the driver to ensure that the printer can be used normally

Search Munbyn Print on Google Play or App Store to get the app or scan the QR code to download and install the application.

Figure 3-20 Search App

Figure 3-21 Munbyn Print App

Figure 3-22 Demo video

Notes: After opening the app, select allow the app to locate permission (Android only) and use the phone’s Bluetooth permission.

Wi-Fi Mac Printer Installation

Notes: To use the P4S printer on a PC, please install tis printer driver in advance.

1. Get the latest driver from this lnk
2. If your sytem is updated please reinstall the divert ensure thatthe printer can be used normally

Search Munbyn Print on Google Play or App Store to get the app of scan the QR code to download and install the application.

Figure 3-23 Search App

Figure 3-24 Munbyn Print App

Figure 3-25 Demo video

Note: After opening the app, select allow the app to locate permission (Android only) and use the phone’s Bluetooth permission.

Product Specification

Humidity: 10-90%(non-eondensing)
Storage Environment| Temperature: -40 to 80°C
Humidity: 5-95%(non-condensing)
Connection| USB/Wi-Fi
Weight| 815g
Dimension| D 198mm•W 82mm•1.1 93mm

Scan the QR code for Facebook online chat

FCC Warning Statement: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement

The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co – located for operating in conjunction with any other antenna or transmitter.

Contact us

MUNBYN provides 18 month’s warranty and lifetime free service.
If you encounter any issues with the product, please contact the MUNBYN team to promptly receive troubleshooting tips or a replacement. Email: support(a)munbvn.com (24-7 online support) Website: www.munbyn.com (how-to videos) WhatsApp: +8617817881067
Phone: +I 650 206 2250

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>