westfalia 62 09 89 Angle Grinder Support Instruction Manual

westfalia 62 09 89 Angle Grinder Support

Dear Customers
This angle grinder stand is ideal for many cutting jobs. It can be used with most angle grinders with cutting discs with a diameter of 115 mm or 125 mm.
Before first use please familiarize yourself with the proper usage of the device. Keep these operating instructions for future reference.
This operating instruction contains important details for handling the device. Please pass it on along with the unit if it is handed over to a third party!
Please read the safety instructions most carefully!
These instructions will make it easier for you to handle the device appropriately and help prevent misunderstandings and possible damage.

Overview

Note: The part numbers refer to the part list of the exploded view found at the end of this manual.

Safety Notes

Please note the following safety notes to avoid malfunctions, damage or physical injury:

• Please read this manual carefully and use the unit only according to this manual.

• Dispose of used packaging material carefully or store it out of the reach of children. There is a danger of suffocation!

• Keep children away from your working area!

• When working with an angle grinder, always wear safety goggles, ear protection and safety gloves. If you have long hair, it is advisable to wear a cap or hair net. Depending on the material you cut, wear a dust mask.

• Do not wear loose-fitting clothing when working with an angle grinder.

• Mount the angle grinder stand on a workbench or similar with the mounting holes in the base plate. Make sure the angle grinder stand and the workbench have a firm stand.

• Keep your working area organised and well lit.

• Do not touch the rotating cutting disc with any part of your body. There is a risk of injury.

• Always use the safety hood (12) for the cutting disc.

• Use the angle grinder stand only with an angle grinder which is equipped with a metal hood for the cutting disc.

• Position the hood in such a way that the cutting disc is only accessible from the bottom and the hood can not touch the work piece.

• Cutting causes flying sparks. Make sure no flammable material is in your working area. The sparks may also damage paint, glass and other surfaces.

• Do not wear garments made of nylon or polyester, wear only suitable work clothes of low flammability.

• Make sure the power cord of the angle grinder is out of the cutting area and out of the range of the sparks.

• Make sure the work piece is clamped tightly and rests solidly on the base plate.

• Do not cut work pieces which are too large to be clamped solidly with the clamping jaws on the base plate.

• Store the angle grinder in a dry place which is free from dust.

• Regularly check the screws for tightness during work. Regularly check the angle grinder stand for damage. Vibration can loosen the screws of damage parts. Do not use the angle grinder you find damaged parts on it.

• Make sure the cutting disc is in a right angle to the base plate.

• Only use cutting discs with the stand, Never use grinding discs.

• Regularly check the cutting disc for damage. Do not use it if you detect bent areas, dents or other damage.

• Always pull the power plug of the angle grinder when undertaking any maintenance or performing adjustments on the angle grinder stand.
  

• Always wear eye protection, ear protection, safety gloves and, if necessary, a cap or hair net when working with the angle grinder stand.

Assembly Instructions

Assembly Instructions

Please follow the sketches to set up the stand. Depending on the angle grinder, you require up to 7 open end spanners (8 mm, 2 x 10 mm, 2 x 14 mm and possibly 2 x 17 mm), two Allen wrenches (5 mm and 6 mm) and a slot screwdriver (approx. 5 mm).
Mount the saddle (2) with the Allen screws (4) and the washers (3) on the base plate (1).
Mount the handle (10) with the embedded screw and the corresponding nut on the retainer (6). Place a washer (21) between nut and retainer.
Attach the angle grinder to the retainer (6). Please notice that the angle grinder has to be equipped with the correct cutting disc before mounting. The cutting disc can not be changed while the angle grinder is attached to the stand. Now check whether your angle grinder is equipped with a 10, 8 or 6 mm treated mounting hole for the accessory handle. Find the correct retaining screws (8) and the corresponding nuts (9). (Please follow figure B).

Stick the correct retaining screws (8) through the mounting pieces (14). Because most angle grinders require 8 mm screws, the correct plastic inserts for 8 mm screws are already installed. If you require a different size of screw, remove the plastic insert and use the smaller insert for the smaller 6 mm screws or no insert for 10 mm screws. Mount the mounting pieces (14) by clamping them with the nuts (9).
Insert the adjusting screw (13) into the lower hole and the adjusting screw (7) into the upper hole of the retainer (6). The rubber buffers of the screws must rest on the housing of the angle grinder after mounting (See figures A and D). Initially, retract the rubber buffer against the retainer (6).
Now insert the plastic retainers (15) of the mounting pieces (14) into their guides in the retainer (6) (figure B). Now mount the mounting pieces (14) and the plastic retainers (15) with the Allen screws (5) in the slotted holes of the retainer (6).
Use the adjusting screws (7) and (13) to adjust the angle grinder in a right angle to the base plate (1) and mounted without slack on the retainer.
Adjust the saddle (2) after loosening the Allen screws (4) in such a way that the cutting disc exactly dives into the slot in the base plate (1).
Now mount the safety hood (12). Attach the hood (12) to the metal rod (11) and secure it with the nuts (29). Then, insert the metal rod into the corresponding hole in the retainer (6) (figure C) and secure it with the nut (28) and the screw (27).

After mounting, turn on the angle grinder and allow it to run for several seconds. After that, pull the power plug of the angle grinder and check all screws for tightness.

Operation

• Place the work piece on the base plate against the rear stop (24) and secure it with the jaw (23). Make sure the work piece sits solidly on the base plate. Adjust both jaws in such a way that the work piece lies in the middle of the cutting disc.
• Now turn on the angle grinder and bring the cutting disc down onto the work piece.
• Avoid sharp impacts and apply even force on the work piece.

Maintenance, Cleaning and Storing

• Clean the unit from time to time with a dry paint-brush or a brush in order to remove residues.
• Do not clean the unit with aggressive detergents or aggressive chemicals.
• The unit is maintenance-free and does not require any lubrication.

Parts List

Exploded View

Customer Services

Deutschland
Westfalia
Werkzeugstraße 1
D-58093 Hagen
Telefon: (0180) 5 30 31 32 Telefax: (0180) 5 30 31 30
Internet: www.westfalia.de

Österreich
Westfalia
Moosham 31
A-4943 Geinberg OÖ
Telefon: (07723) 4 27 59 54 Telefax: (07723) 4 27 59 23
Internet: www.westfalia-versand.at

Schweiz
Westfalia
Wydenhof 3a
CH-3422 Kirchberg (BE)
Telefon: (034) 4 13 80 00 Telefax: (034) 4 13 80 01 Internet: www.westfalia- versand.ch

Disposal
Dear Customer,
Please help avoid waste materials.
If you at some point intend to dispose of this article, then please keep in mind that many of its components consist of valuable materials, which can be recycled.
Please do not discharge it in the rubbish bin, but check with your local council for recycling facilities in your area.

© Westfalia 04/22

References

• Westfalia Versand Österreich | Werkzeug ✓ Garten ✓ Technik ✓ & mehr
• Westfalia Versand Schweiz | Werkzeug ✓ Garten ✓ Technik ✓ & mehr
• Westfalia Versand Deutschland | Werkzeug ✓ Garten ✓ Technik ✓ & mehr

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>