easee Equalizer Small and Light Sensor Device User Guide

June 9, 2024
easee

easee Equalizer Small and Light Sensor Device

Introduction

The information in this leaflet applies to Easee Equalizer P1 (E02-EQP) and Easee Equalizer HAN (E02-EQ), unless specified otherwise.
Read the Important product information guide in the product packaging or at easee.com/manuals before using the product.

Optimal performance
The Equalizer makes it possible to charge smarter, safer and faster if the installation is scaled accordingly. To enable its true potential, the rated value of the chargers circuit fuse should be as high as possible compared to the main fuse.

Product overview

Technical specifications

General

  • Dimensions Product 110 x 110 x 27.5 mm (H x W x D)
  • Dimensions Product Packaging 130 x 130 x 39 mm (H x W x D)
  • Permitted temperature -20 °C to +50 °C
  • Weight 95 g (Equalizer P1) 110 g (Equalizer HAN)
  • IP degree IP40
  • Supply 5-30 V DC 100 mA (Equalizer P1) 20-32 V DC 30 mA (Equalizer HAN)

Cabling

  • Cable length 1.5 m
  • Custom made cable RJ12 to RJ12 (Equalizer P1) RJ12 to RJ45 (Equalizer HAN)
  • It can be extended using an extension cable up to 15 m (Equalizer P1) up to 200 m (Equalizer HAN)

Max transmitted power

  • Radio 25 mW at 863–870 MHz.
  • WiFi 50 mW at 2.4–2.472 GHz.

Connectivity

  • Easee Link RFTM and WiFi1
  • HAN (NVE/AMS) (Equalizer HAN) or P1 (Equalizer P1) smart meter communication
  • Modbus connection to energy meter2
  • Monitor power consumption with the Easee App
  • RFID / NFC reader

WiFi is required for normal operation and for future software updates. Installations with multiple master chargers need to be connected to the same WiFi for load balancing to work.
Easee Link RF (TM) via radio may be limited by walls, concrete or other obstacles.
Only for supported meters.

Installation

Customer setup

Follow these steps if you are a private customer installing the Equalizer in your own household.

  1. HAN port
    Activation
    In Scandinavia, the communication port on the smart meter is most likely not activated. Contact your utility company to open the HAN port for use with the Equalizer.
    If you are not in Scandinavia, skip to step 2.

  2. Easee App
    Download
    Scan the QR code to download the Easee App and create a free account.

  3. Equalizer
    Setup
    Add the Equalizer in the app, follow the on-screen installation guide and get ready to balance your energy smarter than ever before!

easee-Equalizer-Small-and-Light-Sensor-Device-3

Installer setup

  1. Installer App
    Download
    Scan the QR code to download the Installer App and create a free account.

  2. Equalizer
    Setup
    Add the Equalizer to a new or existing charging site using the Installer App and follow the on-screen installation guide to set it up.

  3. Smart meter
    Connect
    Connect the Equalizer to the smart meter using the provided cable. The Equalizer will appear in the Easee Portal after a while.

easee-Equalizer-Small-and-Light-Sensor-Device-4

LED colours meaning

White, fast flashing – Booting

White, breathing every 10s – Normal operation

Red/white, switching – No WiFi added3

Red, flashing – No data from power meter4

Red, breathing every 10s – Error5

Purple, breathing every 10s – Offline operation6
Touch the Easee logo in the middle to check power consumption:

Blue, fast flashing – High power consumption
Blue, slow flashing – Low power consumption
Count the flashes for percentage – 1 flash (10%), 2 flashes (20%), up to 10 flashes (100%)

Hold the Easee logo for 3 seconds to check connectivity. You will see 2 flashes:
1st flash – Easee Link RF status7 2nd flash – WiFi status
Green – Connected
Red – Not connected

  • Use the Easee App to set up the WiFi.
  • Contact your utility company to activate the HAN port. 5 Go to http://easee.support.
  • Check your internet connection.
  • After booting, it can take a few minutes before Easee Link RFTM status flashes green.

Practical details

Warranty
The device is free from material defects and is in accordance with laws and regulations for consumer protection in the country where the product is purchased. All correctly installed Easee hardware is covered by our 3 years limited warranty.
Some countries may have extended warranty.

Returns and complaints
Contact your distributor or Easee Customer Support at easee.support regarding the return and complaint of your product.

The information in this document is for information purposes only, is provided as is, and may be subject to change without notice. Easee AS including its subsidiaries does not accept any liability for the correctness or completeness of the information and illustrations, and is not liable or responsible for your considerations, assessments, decisions or absence of such, or other use of the information in this document.

No part of this publication may be republished, reproduced, transmitted or re- used in any other form, by any means or in any form, for your own or any third-party’s use, unless otherwise agreed with Easee or its subsidiaries in writing. Any permitted use shall always be done in accordance with good practice and ensure that no harm may be caused to Easee or by misleading the consumer.

Easee and Easee products, product names, trademarks and slogans, whether registered or not, are Easee’s intellectual property and may not be used without Easee’s prior written permission. All other products and services mentioned may be trademarks or service marks of their respective owners.
January 2023 – Version 1.00
© 2023 by Easee AS. All rights reserved.

Easee AS Grenseveien 19
4313 Sandnes, Norway
www.easee.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals