vtech VM5263 Full Color Pan and Tilt Video Monitor User Guide

vtech VM5263 Full Color Pan and Tilt Video Monitor User Guide

Important safety instructions

The applied nameplate is located at the bottom of the baby unit’s base.
When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:

1. Follow all warnings and instructions marked on the product.

2. Adult setup is required.

3. CAUTION: Do not install the baby unit at a height above 2 meters.

4. This product is intended as an aid. It is not a substitute for  responsible and proper adult supervision and should not be used as such.

5. This product is not intended for use as a medical monitor.

6. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower.

7. CAUTION: Use only the battery  provided. There may be a risk of explosion if a wrong type of battery is used for the parent unit. The battery cannot be subjected to high or low extreme temperature and low air pressure at high altitude during use, storage or transportation. Disposal of battery in to fire or a hot oven, or mechanically crushing or cutting or the battery can result in an explosion. Leaving the battery in an extremely high temperature surrounding environment can result in an explosion or the leakage offl ammable liquid of gas. Battery subjected to extremely low air pressure may result in an explosion or the leakage offl ammable liquid or gas .Dispose of used battery according to the information in The RBRC® seal.

8. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product.
   Power adapter information: Parent unit output: 5V DC 1A  VTech Telecommunications Ltd.
   Model: VT05EUS05100
   Baby unit output: 5V DC 1A.
   VTech Telecommunications Ltd.
   Model: VT05EUS05100
   Rechargeable battery information: Li-ion battery, 3.8V 2100mAh
   Zhongshan Tianmao Battery Co., Ltd. Model Number: BP1763

9. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.

10. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible.

11. Unplug this product from the wall outlet before cleaning.
    Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

12. Do not cut off the power adapters to replace them with
    other plugs, as this causes a hazardous situation.

13. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped.

14. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company.

15. Do not overload wall outlets or use an extension cord.

16. Do not place this product on an unstable table, shelf, stand
    or other unstable surfaces.

17. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register.

18. Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product.

19. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the product other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.

20. You should test the sound reception every time you turn on the units or move one of the components.

21. Periodically examine all components for damage.

22. There is a very low risk of privacy loss when using certain  electronic devices, such as baby monitors, cordless telephones, etc. To protect your privacy, make sure the product has never been used before purchase, reset the baby monitor periodically by powering off and then powering on the units, and power off the baby monitor if you will not use it for some time.

23. Children should be supervised to ensure that they do not
    play with the product.

24. The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

SAVE THESE INSTRUCTIONS

Cautions

1. Use and store the product at a temperature between 32oF and 104 F.
2. Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source.
3. Batteries should not be exposed to excessive heat such as bright sunshine or fire.
4. Warning—Strangulation Hazard— Children have STRANGLED in cords. Keep  this cord out of the reach of children  (more than 3 ft (0.9m) away). Do not remove this tag.
5. Never place the baby unit(s) inside the baby’s crib or  playpen. Never cover the baby unit(s) or parent unit with anything such as a towel or a blanket.
6. Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones.

Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless devices):
Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:

Pacemaker patients

• Should keep wireless devices at least six inches from the pacemaker.
• Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON. WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices. Electromagnetic fields (EMF) This VTech product complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user’s manual, the product is safe to be used based on scientific evidence available today.

What’s in the box

Connect the baby monitor

NOOTTEES

• The rechargeable battery in the parent unit is built-in.
• Use only the power adapters supplied with this product.
• Make sure the baby monitor is not connected to a switch-controlled electric outlet.
• Connect the power adapters in a vertical or floor mount position only. The adapters’ prongs are not designed to hold the weight of baby monitor, so do not connect them to any ceiling, under-the-table, or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets.
• Make sure the parent unit, the baby units and the power adapter cords are out of reach of children.

Overview – Baby unit

1. Light sensor
2. Camera lens
3. Microphone
4. Night light
5. On/Off switch
6. On/Off LED light
   • On when the baby unit is turned on and is paired to the parent unit.
   • Flashes when the baby unit is not being viewed; or when the link to the parent unit is lost.
7. Speaker
8. Night light on/off key
9. Power jack
10. Slots for wall mounting

Need help?

For operations and guides to help you using your video monitor, and for latest information and supports, go and check the online help topics and online FAQs.
Use your smartphone or mobile device to access our online help.

• Go to https://help.vtechphones.com/vm5263 or https://help.vtechphones.com/vm5263-2; OR
  VM5263

• Scan the QR code on the right. Launch the camera app or QR code scanner app on your smartphone or tablet. Hold the device’s camera up to the QR code and frame it. Tap the notification to trigger the redirection of the online help.

  • If the QR code is not clearly displayed, adjust your camera’s focus by moving your device closer or further away until it is clear.
    You can also call our Customer Support at 1 800-595-9511 [in US] or 1 800-267-7377 [in Canada] for help.

VM5263-2

Power on or off the baby monitor

1. Slide the switch to power on or off your baby unit.

2. Press and hold POWER to power on or off your parent unit.

Positioning the baby monitor

Caution

• The default volume of your parent unit is level 4, and the maximum volume is level 7. If you experience high-pitched screeching noise from your baby monitor while positioning:
  • Make sure your baby unit and parent unit are more than 3 feet (1 meter) apart, OR
  • Lower the volume of your parent unit.
    

Note

• To avoid interference from other electronic devices, place your baby monitor at least 3 feet (1 meter) away from devices such as wireless routers, microwaves, cell phones and computers.

Status check

Once you power on both your baby unit and parent unit, your parent unit displays image from the baby unit, and the LINK LED light turns on.
The ON LED light of baby unit turns on.

Basic operation – Parent unit

Adjust speaker volume
Press-VOL/ VOL- to adjust your parent unit speaker volume.

Talk to your baby unit
Press and hold TALK and speak to your parent unit. Your voice is transmitted to the baby unit. Release TALK when finish talking and hear your baby again.

Zoom
Press  to zoom in or out.

Turn off the screen
Press and hold LCD ON/OFF to switch off the screen. You can still hear sound from the baby unit.

Tip

• Press any keys on the parent unit to turn on the screen again.

Use the menu
Press to enter the menu, choose a menu item, or save a setting. You can use the parent unit for advanced settings or operations, such as to play or stop the baby unit lullaby, or to adjust the baby unit sound sensitivity.
While in the menu:

• Press < or> to scroll among the menu options.
• Press to select an item, or to save a setting.
• Press or to scroll among the sub-menus, or to adjust a setting.
• Press < to return to the previous menu options without changing the current setting.
• Press /EXIT to return to live video.

Overview – Parent unit

1. LED lights
2. LCD display
3. Microphone
4. POWER
5. TALK
6. MENU/SELECT
7. Arrow keys
8. Volume
9. VIEW /LCD ON/OFF
10. EXIT
11. Antenna
12. RESET
13. Stand
14. Power jack

Power on or off the baby monitor

1. Slide the switch to power on or off your baby unit.

2. Press and hold POWER to power on or off your parent unit.

Parent unit icons

Main menu icons

Main
menu Sub-menu

Brightness

• Adjust the parent unit’s LCD brightness.

Camera settings

Baby unit speaker volume

• Adjust the baby unit’s speaker volume.

Monitoring mode (For VM5263-2 only)

• Single mode
• Split mode
• Patrol mode

Lullaby

Play/Stop lullaby

• Select one of the soothing sounds, or white noise.

• Select one of the five melodies.

• Play all melodies.

• Set timer to stop playing the selected melody or soothing sound.

Main
menu Sub-menu
Night light

Turn on/off night light

• Select one of the night light colors.

• Change to all seven colors in cycles.

• Set timer to turn the night light off.

• Select to set the night light to always on.

• Set to auto turn on the night light when baby unit detects sound. It will turn off after 15minutes of no sound detection. You can set VOX sensitivity level to detect sounds that exceed certain levels. See Sound sensitivity and sound activation section.

Turn on/off the adaptive night light feature. When this feature is on, the baby unit detects the ambience light.
If the room is bright, the night light adjusts itself to be brighter; if the room is dim, the night light adjusts itself to be less bright.

Turn on/off temperature alert tone.

• Set the parent unit to beeps whenever the room temperature detected by the baby unit falls outside of the set temperature range.
• Set the minimum temperature.
• Set the maximum temperature.
•  Set temperature display in Fahrenheit (oF) or Celsius (oC)

Main
menu Sub-menu
Alert tones

• Set the parent unit to beep when the battery is low.
• Set the parent unit to beep when the link between the parent unit and the baby unit is lost.
• Set the confirmation tone on or off when selecting an option in the menus.
• Set the parent unit to beep when the baby unit detects sounds while in Split mode (For VM5263-2 only).

Sound activation – screen and audio

Turn on/off sound activation

• Set sound activation on or off.
• When it is on, and the baby unit detects no sound, the parent unit screen stays off to save power. Once a sound is detected, the parent unit screen and speaker turns on automatically, and you can see and hear your baby. The parent unit will then turn off again after 50 seconds of no sound detection.

Note

• When the parent unit screen is off and it receives alerts, for example, link lost between parent unit and baby unit, or battery is low, the parent unit screen and speaker will turn on for 10 seconds.

VOX (Voice Activated Alert) Sensitivity

• You can set VOX sensitivity level to activate parent unit screen and sound when baby unit detects sounds that exceed certain levels. See Sound sensitivity and sound activation section.

References

• VTech Canada Official Site | Best Home Office & Business Phones
• VTech Cordless Phones Official Site | Best Home Office & Business Phones
• VTech Cordless Phones Official Site | Best Home Office & Business Phones
• Product Support | VTech® Cordless Phones

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>