A D WinCT-UFC Windows Communication Tools Software User Manual

June 4, 2024
A D

WinCT-UFC Windows Communication Tools Software
User Manual 

WinCT-UFC Set Up EN Ver. 2.20 for Windows 10 / Windows 8.1 / Windows 7 Copyright (c)
2020 A&D Company, Limited

Setup

WinCT – UFC (Windows Communication Tools for UFC)
This software “Windows Communication Tools for UFC” (“WinCT-UFC”) serves as the Windows setting tools for editing UFC Output Format on a PC to output from an A&D weighing instrument equipped with the UFC function and for storing it in the weighing instrument.
Below are instructions for the installation and use of WinCT-UFC.

System Requirements

1-1.PC
OS: Microsoft Windows 10 / Windows 8.1 / Windows 7
1-2.Weighing instruments
WinCT-UFC can be used with the following A&D weighing instrument equipped with the UFC function (see table below).
As of May 2022

Weighing instrument Model
Precision balances BA series

BA-T series
(The touch panel software version 1.01 s or later)
GX-A/GF-A series
GX-M/GF-M series
Counting scales| FC-i/FC-Si series
HC-i series
Digital platform scales| HV-C/CP and HW-C/CP series
Checkweighing scales| FS-i series

1-3. Cable Please refer to the manual of the intended model.
Note – Back up important data in the PC before installing WinCT-UFC.

Installation Instructions

Step 1 If a previous version of WinCT-UFC is installed on the PC uninstall it.
Step 2 Close all open applications in Windows.
Step 3 Install WinCT-UFC. Run Setup-UFC.msi.
Step 4 The setup wizard is displayed. Please click [Next].
Step 5 Select the installation folder, and click [Next].
Step 6 Click [Next].
Step 7 Installation will start. Please wait for a while to complete it.
Step 8 When the installation is complete, click [Close] to finish.

Starting WinCT-UFC

Select WinCT-UFC from the START menu. The default menu address is [Start] – [program] – [A&D WinCT-UFC]. You will find the instruction manual in the Readme file under [A&D WinCT-UFC].
Note – WinCT-UFC is a program for balances that use the A&D format. A&D does not guarantee performance or
compatibility when other manufacture’s balances are used with WinCT-FRD. – If you have problems or questions about compatibility with third-party software, contact the manufacturer
for information.

License Agreement and Limited Warranty

  • WinCT-UFC is subject to change without notice and does not represent a commitment by A&D to support earlier versions or to make changes to support nonstandard computers.

  • WinCT-UFC is intended for the transmission of data from an A&D balance to a PC, and command transmission for controlling the balance.

  • Under copyright laws, the WinCT-UFC program may not be copied, in whole or part, without the consent of
    A&D, except as specified in the license agreement.

  • WinCT-UFC should only be installed on the hard disk or peripheral storage devices of a PC connected to an A&D weighing instrument.

  • A&D bears no liability for direct, indirect, special, incidental, or consequential damages resulting from any defect in the WinCT-UFC program or the readme file, even when advised of the possibility of such damage.

  • A&D is not responsible or liable for the loss of any programs and/or data stored in the PC on which WinCT-UFC was installed, including the costs of recovering said lost programs or data.

Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation.

Uninstallation Instructions

-Use the “Add/Remove Programs” icon in the control panel to remove this program from your PC.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals