anko I004775 Wi-Fi Smart Pan and Tilt Camera User Guide
- June 9, 2024
- Anko
Table of Contents
I004775 Wi-Fi Smart Pan and Tilt Camera
User Guide Quick Start Guide
Wi-Fi Smart Pan &Tilt Camera
Model I004775
KEYCODE: 43274604
Package contents
Description
- Micro SD card slot (for local storage, max.128GB)
- Indicator light
- Camera lens
- Reset: Press and hold the ‘reset’ for 5 seconds to reset the device
- Speaker
- Power: Type-C USB (DC 5V/1A)
- Hole for wall hanging
- 1/4” Screw hole
Connection Preparation
It is important that your phone is connected to a 2.4Ghz Wi-Fi and not to a
5GHz network.
To verify your mobile device is set to a 2.4Ghz Wi-Fi network, navigate to the
Settings menu and click on Wi-Fi. In this menu you will see all the available
networks in your area. Locate the SSID (the name of your network) and ensure
that the Wi-Fi SSID does not end with a 5G / 5GHz.Check that you have a strong
Wi-Fi signal (at least two bars) in the location where the smart camera is to
be installed.
If you don’t have at least two bars signal on your phone, then you may need to
reconsider relocating the camera to a different location or obtain a Wi-Fi
extender to boost the Wi-Fi signal strength.
Install the Mirabella APP and register Account
To access your camera and it’s functions download the “Mirabella Genio” APP to
your smartphone from the App Store or Google Play then add your device to the
APP.
Insert a Micro SD card
Please note that the camera will work without an SD card, but it will not be
able to record any footage.
Insert the Micro SD card gently into the SD card slot. Please pay attention to
the direction of the Micro SD card. Do not force it inside. Micro SD card size
needs to be between 8GB and 128Gb, FAT32 format only, This camera doesn’t
support NTFS file system.
Pairing the camera using Mirabella Genio App
- Power on the camera and wait for the indicator light to start blinking BLUE rapidly. (1 blink every second) if it fails to blink, Use the reset pin provided and insert into the reset port and hold until you hear an audible sound, the camera is now ready to pair.
- Check your mobile phone is connected to the 2.4Ghz Wi-Fi network, (Wi-Fi name should not end with -5G).
- Open the Mirabella Genio APP, tap on blue “+” icon, then choose add device, then select Security & Sensor and select your camera from the list.
- Confirm that the LED indicator light is still blinking rapidly blue, tap “confirm Indicator is blinking BLUE rapidly”, then tap “next” and enter your home network 2.4GHz Wi-Fi name and password.
Tap next and the QR code will appear on your phone screen, place this QR code in front of the camera at approximate 15-20cm, until you hear a sound,Tap on “Beeped/ Indicator switched” It will then start to connect your device. (refer to the 1st & 2nd images).5. Once the countdown ends, the Camera has now successfully been paired to your APP. Please refer to the FAQ section for troubleshooting if this method does not connect.if somehow the QR code method does not work , please reset and retry using the EZ method.
FAQ
Q. LED indicator is not blinking rapidly as per APP screen****
– A. Power off the camera, wait for 20 sec, depress the reset button until you hear a sound, then release the button, wait for another 30-40 sec until the light starts to blink blue rapidly again (1 blink every second).
Q. Camera doesn’t scan the QR code****
– A. Please ensure camera is in the pairing mode, indicator light is blinking blue rapidly as per the APP screen, if you are unsure, please simply reset it.
Q. I am using Telstra NBN, I disabled the 5Ghz and still can’t get it to pair?****
– A. Please follow the Guest Network paring instructions at https://mirabellagenio.net.au/faqs
Q: Camera will not connect to my Wi-Fi network
– A: Make sure the Wi-Fi network is a 2.4GHz network, device will not connect
to a 5GHz network.Also make sure your Wi-Fi name has no space, your Wi-Fi
network password is case sensitive, make sure you are entering it correctly.
– Refer to our website’s FAQ and check for your router Is listed as some
routers are set up differently.
Q: The camera is off-line****
– A: There could be a temporary issue with your internet connection (e.g.,
service disruption). Please try again in a few minutes. Make sure your Wi-Fi
router is turned On. Make sure the camera is getting a good signal from your
Wi-Fi router.
– Use your phone to check range, it is recommended to have at least 2 signal
bars showing proper connection.
Q: How to reset the camera to renter pairing mode?****
A: Press and hold reset button (see Product Details section) until you hear an audible tone.
Q: Live video stream is slow to load****
– A: Camera streaming issues may be caused by any of the following: Your phone’s cellular connection, which relies on mobile overage.Limited internet bandwidth at home, for example, other video streaming services running at the same time on your network can cause congestion slowing down the internet upload and download speeds.Wi-Fi reception may not be stable or work reliably if the camera’s Wi-Fi signal strength is less than 2 signal bars. You may need to install a Wi-Fi repeater or extender to boost the Wi-Fi signal.
Q: The camera is not recording?****
– A: Make sure that the microSD card is installed correctly. To confirm the
camera is recognizing the microSD card, go to storage Settings in the Settings
menu and make sure the microSD
– Card capacity shows Total capacity, Used and Free space. If this does not
appear you may consider reformatting the microSD card. WARNING:Reformatting
micro SD card will delete all videos stored on card. Once SD card is
formatted, your recordings will be stored on the card and can be accessed via
the playback button.
Q: What happens when the microSD card reaches full capacity?****
– A: Once the microSD card reaches full capacity, new videos will start rewriting (deleting) over the oldest videos.
Q: Why I can’t get the notifications with my cell phone App?****
– A: Confirm that the App has been running on the phone, and the relevant reminder function has been opened; Message notification and authority confirmation in the mobile phone system have been enabled.
How to connect camera to another router
Go to the camera settings page, look for “remove device” Remove it and reset
the camera, pair it again to the new router through the app.
Poor performance, takes a long time to load the live footage
Please check the Wi-Fi signal, if it is less than 60%, you will need consider
changing the camera location or purchasing a Wi-Fi extender to boost the
signal.
Camera went offline and doesn’t reconnect back online by itself
Go the camera’ settings page, look for “remove device” Remove it and reset the
camera and pair it again through the app.
Followed the pairing process but still receive the error Cannot find
Device
Manually disable the 5Ghz Wi-Fi signal on the router setting.
Ensure that the 2.4Ghz Wi-Fi signal is on.
Ensure the indicator light is blinking BLUE rapidly as per APP screen (1 blink
per second)
Please check you have entered the correct 2.4Ghz Wi-Fi SSID and password.
I am using Telstra NBN, I disabled 5Ghz and I still cannot get it to pair
Please follow the Guest Network paring instructions on
https://mirabellagenio.net.au/faqs If you have done all of the above,
ensuring that 5Ghz is disabled.
How to turn on or turn off movement notification
On the Genio APP home screen, Tap on Me -> Settings -> App Notification ->
turn on/off Enable notifications.
On the iphone, Settings -> Notifications -> turn on/off Allow Notifications
for the Mirabella Genio app.
For multiple camera setup, change camera view or arrange device set up
sequences and manage rooms.
On the genio APP home screen, tap on on the top right corner, to access these
options, tap on V to switch below rooms. Tap on x to exit this mode.
Need more help or need further technical assistance from Mirabella
engineer
On the genio APP home screen, tap on, Me, -> FAQ & Feedback -> Report issue
Fill the fault information or suggestion for the APP/product, then submit
Remember the performance of your Wi-Fi camera is relies heavily on the
performance of your router
If you are using Telstra NBN or a dual-band router, you must disable the 5GHz
Wi-Fi in order to make a successful connection and for best overall
performance, as MOST smart products in Australia only work on the 2.4Ghz
signal.
All trademarks are used for reference purposes only.
Made in China
ANKO, HOME&CO AND AUDIOSONIC® ARE TRADEMARKS OF KMART AUSTRLIA LIMITED.
MIRABELLA INTERNATIONAL PTY LTD
1 MIRABELLA DRIVE, TULLMARINE, VIC, AUSTRALIA 3043
TOLL FREE: 1800 636 528
www.mirabellagenio.com.au
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>