ancona PBS1246 36 Inch Stainless Steel Backsplash with Magnetic User Manual

: June 9, 2024
: ancona

Table of Contents

Included Parts
Measurements and Diagrams
Installation
Use and Care Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ancona PBS1246 36 Inch Stainless Steel Backsplash with Magnetic User Manual

Included Parts

Hardware Note : For safety reasons, backsplash mounting screws and anchors will not be included due to the variation of cabinetry constructions and wall material. Please consult you installation specialist regarding the optimal type of mounting screws and wall anchors to suit your home’s construction.

Included Parts

Measurements and Diagrams

30 inch
Measurements and Diagrams

36 inch
Measurements and Diagrams

Installation

IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE INSTALLING

Note: Use threaded drywall anchors only when mounting the backsplash on sheetrock.

The backsplash installs to cover the wall space from the bottom of the hood to the cooktop/counter.
It can be installed during the installation of the hood or after.
If the hood is already installed, remove the hood lters, grease trays and lights and put in a safe place. Then if necessary, remove the hood to allow installation of the backsplash.

Open the packaging carefully to avoid damaging the backsplash.
Install the shelf using 8 supplied screws ST4×8 (see Figure 1)
Install the rail to backsplash using 2 supplied screws M4×10 (see Figure 2)
Fix the pillar to rail using 2 supplied screws M4×50 and 2 supplied pillars, secure the rail to shelf (see Figure 3).
Locate the midpoint of the hood at the wall. Draw a vertical centerline from this midpoint to the cooktop.
Position the backsplash on wall centered on the marked centerline and with lower edge Cooush with the cooktop/counter.
Mark where the screw holes are on the bottom and the top, drill the holes and screw in the wall anchors. Fix the backsplash to the wall with screws on the bottom and the top (see Figure 4).
Hang the hooks on the handle.
Install the hood **(see Figure 5).

**

Remove the plastic cover from backsplash once it’s xed to the wall.

Use and Care Information

Cleaning Exterior Surfaces

Clean periodically with hot soapy water and clean cotton cloth. DO NOT use corrosive or abrasive detergent (e.g. Comet Power Scrub®, EZ-Off® oven cleaner), or steel wool/scoring pads, which will scratch and damage the stainless steel surface. For heavier soil use liquid degrease such as “Formula 409®” or “Fantastic®” brand cleaner.
If backsplash looks splotchy (stainless steel hood), use a stainless steel cleaner to clean the surface of the backsplash. Follow directions of the stainless steel cleaner. Use a soft towel to wipe off the cleaning solution, gently rub off any stubborn spots. Use a dry soft towel to dry the backsplash.
After cleaning, you may use nonabrasive stainless steel polish such as 3M® or ZEP®, to polish and buff out the stainless luster and grain. Always scrub lightly, with clean cotton cloth, and with the grain.
DO NOT allow deposits to accumulate or remain on the backsplash.
DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface and cause rusting.
DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless steel for extended periods. Many of these compounds contain chemicals, which may be harmful.
Rinse with water after exposure to these compounds and wipe dry with a clean cloth.

Please register your product warranty by visiting the Ancona Home website.

Canada & USA
Phone: 1-800-350-4562
Fax: 800-350-8563
Email: service@anconahome.com
Website: www.anconahome.com

ancona Logo