westfalia 87 28 18 Electric Drill Bit Sharpener 110 W Instruction Manual

westfalia 87 28 18 Electric Drill Bit Sharpener 110 W

Original Instructions

Article No. 87 28 18

Dear Customers
This manual contains important information on operating and handling the device. Keep these operating instructions for further reference. Please pass it on along with the unit if it is handed over to a third party!

Please read the safety instructions!
These instructions will make it easier for you to handle the device appropriate-ly and help prevent misunderstandings and possible damage or injury.

Overview

1. Rotary Stone setting Knob
2. Sharpening Stone Cover
3. Sharpening Stone Cover Screws
4. Sharpening Stone Assembly
5. Bin for Chips with Discharge Slot
6. ON / OFF Switch
7. Control LED
8. Spring
9. Drill Guide
10. Nut (Left Hand Threads)
11. Metal Washer
12. Sharpening Stone
13. Sharpening Stone Holder

Safety Notes

Please note the following safety notes to avoid malfunctions, damage or physical injury:

• The unit is not a toy and does not belong in the hands of children. Never leave the unit unsupervised when in use. Keep it out of reach of children or persons in need of supervision. Children should be supervised to ensure that they do not play with the unit.
• Make sure the power mains voltage in your area corresponds to operating voltage stated on the type label.
• The unit is designed for operation in altitudes of up to 2000 m above sea level.
• Dispose of used packaging material carefully or store it out of the reach of children. There is a danger of suffocation!
• Please read this manual carefully and use the unit only according to this manual.
• Always wear safety goggles. The lenses of your normal spectacles are only impact resistant. They are NOT safety goggles.
• Please keep your fingers away from the guide holes for the drills!
• Avoid unintended starting. Ensure that the switch is turned off before connecting to the power supply.
• This machine is not suitable for outdoor operation.
• Never use the unit grinder in an explosive or flammable environment. Normal sparking of the motor can ignite flammable materials.
• Damaged grinding wheels must be replaced immediately.
• The grinding wheel should rotate evenly. If there is shaking, the grinding wheel should be replaced.

Operation

Adjustment Screw

1. With the adjustment screw (1) you can adjust the position of the stone in the machine. This way the pressure with which the stone is forced against the drill bit is set.
2. Turn the screw to the left to lower the stone. Turn the screw to the right to raise the stone. Do not raise the stone too much; otherwise it may hit the housing.

Operation

1. Place the unit on a flat, level, stable surface and plug the power plug into a suitable socket.
2. Use the switch (6) to turn the unit on and allow it to run for a few moments. Make sure it operates normally. Do not start sharpening before the unit has reached its operating speed. During operation the LED (7) lights up.
3. Insert the drill to be sharpened into the positioning hole of corresponding dimensions. Apply light pressure and repeatedly rotate for several times, after withdrawal rotate by 180° and re-insert into the positioning hole. Repeat the procedure until the drill is satisfyingly sharp.

Removing the Chips

1. During normal operation the chips can be shaken out of the collection bin through the discharge slot by tilting the unit forward.
2. Occasionally the collection bin should be removed as described below and cleaned.

Replacing the Stone

1. A replacement stone can be purchased from Westphalia under the article number 87 39 57.
2. Loosen the cross slot screws (3) on the top of the unit and take the top cover off. Lift out the stone assembly and the bin (5). Clean the container.
3. Do not clamp the stone in a vise or similar device. Hold the assembly in your hand with a work glove.
4. Loosen the retaining nut (10) (left hand threads) and take the assembly apart. Replace the stone (12) and put the as-sembly back together. Put the nut (10) on only hand tight.
5. Place the container and the stone assembly back into the unit. The rectangular end of the drive shaft must engage with the rectangular slot in the stone assembly. If necessary lubricate the upper bearing of the stone assembly with some silicone grease. Reattach the top cover and secure it with the screws (3).

Maintenance and Cleaning

• Before undertaking any work on the machine, disconnect the power plug from the power mains.
• After use, remove all chips and dirt from the unit. Use only a stiff brush and a dry or moist cloth. Do not use solvents or aggressive chemicals and do not allow liquids of any kind to enter the machine.
• The unit does not contain components serviceable by you. Do not disassemble it and do not try to repair it yourself. In the case of questions or problems please turn to our customer support department.

Technical Data

• Operating Voltage 230 V~ 50 Hz

• Nominal Power 110 W

• Nominal Speed 1400 min-1

• Protection Class II

• Sound Pressure Level 76.20 dB(A) K = 3 dB

• Sound Power Level 89.20 dB(A) K = 3 dB

• Sound emissions may differ from the declared values during use depending on the ways in which the tool is used.

EU Declaration of Conformity

We, the Westfalia Werkzeugcompany, Werkzeugstraße 1, D-58093 Hagen,
declare by our own responsibility that the product
Electric Drill Bit Sharpener 110 W
Article No. 87 28 18
is according to the basic requirements, which are defined in the European Directives and their amendments.

• 2011/65/EU  Restriction of the Use of certain hazardous Substances in electrical and electronic Equipment (RoHS)
• 2014/30/EU Electromagnetic Compatibility (EMC)
  • EN 55014-1:2017+A11,
  • EN 55014-2:1997+AC+A1+A2,
  • EN 61000-3-2:2014,
  • EN 61000-3-3:2013
• 2006/42/EC Machinery
  • EN 62841-1:2015+AC,
  • EN ISO 12100:2010

The technical documentations are on file at the QA department of the Westfalia Werkzeug-company.

Hagen, 12th of July, 2022

Thomas Klingbeil,
QA Representative

Customer Services

Deutschland
Westfalia Werkzeugstraße 1
D-58093 Hagen
Telefon: (0180) 5 30 31 32
Telefax: (0180) 5 30 31 30
Internet: www.westfalia.de

Schweiz
Westfalia
Wydenhof 3a
CH-3422 Kirchberg (BE)
Telefon: (034) 4 13 80 00
Telefax: (034) 4 13 80 01
Internet: www.westfalia-versand.ch

Österreich
Westfalia
Moosham 31
A-4943 Geinberg OÖ
Telefon: (07723) 4 27 59 54
Telefax: (07723) 4 27 59 23
Internet: www.westfalia-versand.at

Disposal

Dear Customer,
Please help avoid waste materials.
If you at some point intend to dispose of this article, then please keep in mind that many of its components consist of valuable materials, which can be recycled.
Please do not discharge it in the rubbish bin, but check with your local council for recycling facilities in your area.

References

• Westfalia Versand Österreich | Werkzeug ✓ Garten ✓ Technik ✓ & mehr
• Westfalia Versand Schweiz | Werkzeug ✓ Garten ✓ Technik ✓ & mehr
• Westfalia Versand Deutschland | Werkzeug ✓ Garten ✓ Technik ✓ & mehr

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>