Heimgard In-wall Dimmer 400W User Guide

In-wall dimmer
400W

Quick start guide
version 1.0

What is in the box

Device overview

Connection diagram overview

Notes for the diagrams:
L – Live lead input terminal
N – Neutral lead input terminal
Out – Output terminal of the dimmer
S1 – External switch terminal
COM – Terminal for grounding to the switch connected to the dimmer

Installation and wiring

Electronical properties

• Load (A) 1.8 Max
• Voltage (V) 100-240
• Voltage type AC
• Power source AC

This device should be installed by a licensed electrician in a manner that conforms to local regulations and building codes.
WARNING: Electrical power must be switched off during installation
FIRST ENSURE THE POWER IS OFF at the main circuit breaker, and then test the wires with a probe or multimeter to verify.
Connect the input power and output wires to the correct device terminals. Follow the connection diagram and instructions on the next page.

Wiring diagram

For installation follow the wire diagrams.
Option 1: With push switch and bypass

Option 2: With push switch and without bypass

Option 3: With push switch LV and bypass

Option 4: With push switch LV and without bypass

Startup brightness

This is how bright your lights are when you turn your lights on.

1. Adjust the brightness of your lights to the desired level between 1% – 50%.
2. Double Click the Min. Set button on the dimmer to set the brightness.
3. To delete the startup brightness value set the light brightness to minimum brightness (0%) and double-click the Min. Set button.

Minimum brightness

This sets the minimum brightness level on your dimmer.

1. Adjust the brightness of your lights to the desired minimum brightness.
2. Press and Hold the Min. Set button for 3 seconds or until connected light flashes to set the brightness value.
3. To delete the minimum brightness value set the light brightness to maximum brightness (100%) and press and hold down the Min. Set button until connected light flashes.

Connecting to the Hub

These steps are to be followed after the dimmer has been properly installed and wired by a certified electrician.

1. At the circuit breaker, turn off the power to the dimmer.

2. Open the Heimgard app and follow the steps listed here to connect to your device
   

3. Turn the circuit breaker power on to power up your dimmer.
   It will automatically enter pairing mode.
   The connected light will flash 2 times to indicate powering on.

4. When the connected light flashes 5 times and then remains on, the device has been found in your app.

5. You will now see the In-wall dimmer in your new devices. Configure the dimmer by giving it a name and adding it to a room.
   Your light is now able to be controlled by your app.

Factory Reset

If your dimmer has previously been connected to a different Hub, you may need to perform a factory reset.

1. Quickly press the reset button (C) 5 times continuously.
   If you do not have access to the reset button, turn the power supply on and off 5 times. This could be done either from the circuit breaker in the fuse box or from the connected wired wall switch.

2. The device that is connected to this dimmer will turn on/off 3 times to indicate successful reset.
   You will have to reconfigure your device.
   Note: make sure your connected device is functioning properly.

Technical specifications

further dependent on power factor result when connected to dimmer
| Dimmable LED drivers| 200W@ 100W
230V@ 110V| Maximum permitted number of drivers is 200W divided by driver nameplate power rating
| Incadescent lighting, HV
Halogen lamps| 400W@ 200W
230V@ 110V|
Supported load types| 100-240V~
---|---
Resistive loads
Conventional incandescent| 20-400W @ 230V
20-200W @ 110V
Capacitive loads using bypass
Fluorescent tube lamp (compact / with electronic ballast), electronic transformer, LED| 3-200W @ 230V
3-100W @ 110V
Capacitive loads not using bypass
Fluorescent tube lamp (compact / with electronic ballast), electronic transformer, LED| 20-200W @ 230V
20-100W @ 110V

Important safety information

1. Read through these instructions and follow accordingly.
2. Clean only with dry soft cloth. Household cleaners and solvents can damage the finish on your device.
3. Do not install too close to any heat sources such as radiators, heat registers, stoves or other device that produce heat.
4. Do not use this device near water.
5. Warning: To reduce the risk of fire or electric shock, do not expose this device to rain or moisture.
6. Do not expose device to dripping or splashing.
7. Protect the attached cables from being walked on or pinched, particularly at plugs, convenience receptacles, and the point the exit the apparatus.
8. Only use attachments/accessories specified by the manufacturer.
9. All servicing should be performed by qualified service personnel. Servicing is required when the device has been damaged in any way.
10. Operating temperature: -10°C to +50°C
11. Operating relative humidity: < 95% RH (no condensation)

Dispose the product properly at the end of life. This is electronic waste which should be recycled accordingly.

Need help?
Website: heimgard.com/support
Email: support@heimgard.com
Facebook: facebook.com/heimgardnorge/
Telephone: +47 649 44 422

Visit heimgard.com for more information and tips on how to use.

References

• Forside - Heimgard
• Heimgard support - Heimgard

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>