PRESIDENT DIGIMIKE Microphone Owner’s Manual
- June 9, 2024
- PRESIDENT
Table of Contents
PRESIDENT DIGIMIKE Microphone
PRODUCT OVERVIEW
1
|
Modulation
---|---
2
|
RX
3
|
TX – UP/DOWN
4
|
–
5
|
Ground
6
|
Power Supply
| NRC SETTING NRC | INDICATOR LIGHT | VOICE BROADCAST |
|---|---|---|
| 0 – NRC OFF | The Green light and Red light flash alternately | “ NRC OFF ” |
| 1 – NRC level 1 | The Green LED flashes once every 3s | “ NRC level one ” |
| 2 – NRC level 2 | The Green LED flashes 2 times every 3s La | “ NRC level two ” |
| 3 – NRC level 3 | The Green LED flashes 3 times every 3s La | “ NRC level three |
”
4 – NRC level 4| The Green LED flashes 4 times every 3s| “ NRC level four ”
5 – NRC level 5| The Green LED stays on La LED| “ NRC level five”
INSTALLING THE MICROPHONE
– Connect the microphone to your PRESIDENT radio
USING YOUR MICROPHONE
-
CHANNEL SELECTOR:
These buttons are used to change channel in the UP or DOWN direction and to set up the DIGIMIKE. -
CONFIGURATION KEY:
This key is used to enter the configuration mode. -
PTT (Push To Talk) transmission button:
Push to talk button. Release to receive a message.
CONFIGURATION
To enter the configuration mode:
- Press and hold the central button (2) to enter the parameter settings. The LED lights up and the internal speaker voice broadcasts the current setting, the NRC level (see table).
- Use the UP or DN button (1) on the microphone to modify the current parameter.
- If no key is pressed for 10 seconds, it exits the parameter setting mode and saves the current setting.
When all adjustments are done, press PTT (3) to store and exit. A long beep sounds to confirm the success of the operation.
WARRANTY (In accordance with the warranty conditions in the country of
purchase)
Important: Proof of original purchase is required for warranty service.
WARRANTOR: GROUPE PRESIDENT ELECTRONICS
(“PRESIDENT”)
ELEMENTS OF WARRANTY: PRESIDENT warrants, to the original user, if
purchased from a retail store, that this PRESIDENT product will be free from
defects in materials and craftsmanship, subject to the limitations and
exclusions as set out below.
This warranty extends only to the original user. The warranty will be invalid
if the Product is (A) damaged or has not been maintained in good condition
through reasonable maintenance, (B) has been modified, altered or used as part
of any conversion kits, subassemblies, or any configurations not sold by
PRESIDENT, (C) improperly installed, (D) serviced or repaired by someone other
than an authorized PRESIDENT service center for a defect or malfunction
covered by this warranty, (E) used in any conjunction with equipment or parts
or as part of any system not manufactured by PRESIDENT, or (F) installed or
programmed by anyone other than as detailed by the owner’s manual for this
product.
STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at any time while this warranty is in effect, warrantor will either, at its option, repair or replace the defective unit and return it to you without charge for parts, service, or any other cost (except shipping and handling) incurred by warrantor or its representatives in connection with the performance of this warranty. Warrantor, at its option, may replace the unit with a new or refurbished unit. THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some countries do not allow this exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights, and you may also have other rights which vary from country to country.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the instructions in the owner’s manual you are certain that the Product is defective, pack the Product carefully (preferably in its original packaging). The Product should include all parts and accessories originally packaged with the Product. Include proof of original purchase and a note describing the defect that has caused you to return it. The Product should be shipped freight prepaid, by traceable means, to warrantor at:
CUSTOMER SUPPORT
Group PRESIDENT ELECTRONICS 1007 Collier Center Way, Naples, Florida 34110
USA
The declaration of conformity is available at the following internet
address:
https://president-electronics.com/DC/ACFD600
Naples, Florida 34110
Web:http://www.president-electronics.us
Email :info@president-electronics.us
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>