Heimgard 16A In Wall Switch 16A User Guide
- June 10, 2024
- Heimgard
Table of Contents
Heimgard 16A In Wall Switch 16A
Device overview
Device Specifications
| Input voltage | Output voltage | Output current | Size (LxWxH) |
|---|---|---|---|
| 100-240VAC | 100-240VAC | 16A max | 45.5x45x20.3 mm |
Product Specifications
Compatible Load Types
Load Symbol| Load Type| Maximum Load| Remarks
| LED lamps with transformers| 1220W @ 230V
580W @ 110V| Due to variety of LED lamp designs, maximum number of LED lamps
is further dependent on power factor result when connected to switch
| LED drivers| 1220W @ 230V
580W @ 110V| Maximum permitted number of drivers is 1220W divided by driver
nameplate power rating
| Incandescent lighting, HV Halogen lamps| 3680W @ 230V
1760W @ 110V|
| Low voltage halogen lighting with electronic transformers| 1220W @ 230V
580W @ 110V|
| Electrical appliances such as television, refrigerator, water heating etc.|
3680W @ 230V
1760W @ 110V|
Wiring
Notes for the diagrams:
- L – terminal for live lead
- N – terminal for neutral lead
- L1 – output terminals of the device (controlling connected light source) S – terminal for external switch
- NC – No Connection
Connecting to the Hub
These steps are to be followed after the switch has been properly installed and wired by a certified electrician.
-
At the circuit breaker, turn off the power to the switch.
-
Open the Heimgard app and follow the steps listed here to connect to your device
-
Turn the circuit breaker power on to your switch. It will automatically enter pairing mode.
The LED indicator light on the switch will flash 2 times slowly to indicate pairing. -
When the LED indicator flashes 5 times and then remains on the device has been found in your app.
-
You will now see the In-wall switch in your new devices list. Configure the switch by giving it a name and adding it to a room.
Your device is able to be controlled by your app, remote control or with on- wall switch.
Factory Reset
If your switch has previously been connected to a different Hub, you may need to perform a factory reset.
-
Quickly press the reset button 5 times continuously.
If you do not have access to the device, turn on and off the power supply 5 times from the either the circuit breaker or light switch.
-
The device that is connected to this switch will flash or turn on/off 3 times to indicate successful reset.
You will have to reconfigure your device.
Note: make sure your light bulb is functioning properly
Need help?
- Website: heimgard.com/support
- Email: support@heimgard.com
- Facebook: facebook.com/heimgardnorge/
- Telephone: +47 649 44 422
Visit heimgard.com for more information and tips on how to use.
Important safety information
- Read through these instructions and follow accordingly.
- Clean only with dry soft cloth. Household cleaners and solvents can damage the finish on your device.
- Do not install near any heat sources such as radiators, heat registers, stoves or other device that produce heat.
- Do not use this device near water.
- Warning: To reduce the risk of fire or electric shock, do not expose this device to rain or moisture.
- Do not expose device to dripping or splashing.
- Protect the attached cables from being walked on or pinched, particularly at plugs, convenience receptacles, and the point the exit the apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Unplug this device during lightning storms or when unused for long periods of time.
- All servicing should be performed by qualified service personnel. Servicing is required when the device has been damaged in any way.
- Operating temperature: -10°C to +50°C
- Operating relative humidity: < 95% RH (no condensation)
Dispose the product properly at the end of life. This is electronic waste which should be recycled accordingly.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>