Agri-Fab 45-0531 Deluxe Broadcast Push Spreader Instruction Manual
- June 3, 2024
- Agri-Fab
Table of Contents
45-05313
THANK YOU
FOR YOUR PURCHASE!
Without your product review, we don’t exist.
45-0531 Deluxe Broadcast Push Spreader
If you are happy with our quality products & service, please take just a
moment to leave positive feedback and a short review of our product on our
website or your retailer’s website.
Not totally satisfied?
If you have any issues, don’t hesitate to contact us.
We make mistakes sometimes, but please give us the chance to make it right
before leaving negative feedback against our product.
REF | QTY | PART NO | DESCRIPTION |
---|---|---|---|
1 | 1 | 28463BL3 | TUBE, STAND |
2 | 1 | 28464BL3 | TUBE, LOWER HANDLE |
3 | 1 | 28611 | AXLE, 1/2″ OD HOLLOW |
4 | 2 | 43088 | WASHER, .312 X .734 X .065 |
5 | 1 | 43093 | PIN, COTTER 1/8 X 1-1/2 |
6 | 7 | 43648 | BOLT, HEX 1/4-20 X 1-1/2 G5 |
7 | 1 | 44101 | PIN, COTTER 3/32 X 3/4 |
8 | 1 | 47316 | BOLT, CARR .25-20 X 2.25 |
9 | 1 | 45360 | CABLE, CONTROL (PUSH) |
10 | 1 | Jul-24 | IMPELLER |
11 | 1 | Aug-24 | PLATE, FLOW |
12 | 2 | 45702G | WHEEL & TIRE ASSY 4.10/3.5-4 |
13 | 2 | 45705 | SPACER, PLASTIC EXTRUSION |
14 | 1 | 47994BLK | HOPPER |
15 | 2 | 46699 | BOLT, HEX 1/4-20 X 2 G5 |
16 | 1 | 47063 | PIN, COTTER 5/32 X 2.0 |
17 | 1 | 47141 | NUT, WING 1/4-20 NYLOC |
18 | 9 | 47189 | NUT, HEX 1/4-20 NYLOC |
19 | 2 | 47963 | BEARING, HEX FLANGE .50 ID |
20 | 1 | 48934 | HAIRPIN, AGITATOR |
21 | 2 | 49449 | PLUG, 1″ OD TUBE |
22 | 1 | 68491BL3 | ASS’Y, FRAME WLDM |
23 | 1 | 44589BL3 | HANDLE, TUBE (SHORT) |
24 | 1 | 69209 | ASS’Y, GEARBOX |
25 | 4 | R19171616 | WASHER, .531 X 1 X .059 |
26 | 1 | 28662BL3 | TUBE, HANDLE |
27 | 2 | 44482 | GRIP, HANDLE 1″ ID |
28 | 1 | Mar-91 | OWNERS MANUAL |
45-05313
SAFETY INFORMATION
- Read the information on the chemical package for instructions and cautions on handling and applying.
- Wear eye and hand protection when handling and when applying lawn or garden chemicals.
- Never allow children to operate the vehicle.
OPERATION
Do not use powdered lawn chemicals. They do not give a satisfactory or consistent broadcast pattern.
- Estimate the size of the area to be covered and calculate the amount of material required.
- Set the adjustable stop according to the flow setting recommended in the application chart on this page. Also, refer to the instructions on the packaging for the material to be spread.
- The application chart is calculated for light to heavy coverage at a vehicle speed of 3 mph, or 100 ft. in 23 seconds. Do not exceed 6 mph.
- Make sure the control lever is in the “OFF” position.
- Fill the hopper, breaking up any lumpy fertilizer.
- Start the spreader in motion and then pull the control lever forward against the adjustable stop to the “ON” position.
- Always move the control lever to the “OFF” position before turning or stopping.
- To ensure uniform coverage, make each pass so that the broadcast pattern slightly overlaps the pattern from the previous pass. The approximate broadcast widths for different materials are shown in the application chart on this page.
- For rectangular areas, make two passes across the short ends to create turning areas. For non-rectangular areas, make two passes around the entire border.
- When broadcasting weed control fertilizers, make sure the broadcast pattern does not hit evergreen trees, flowers or shrubs.
APPLICATION CHART
TYPE MATERIAL | FLOW SETTING | SPREAD WIDTH |
---|---|---|
FERTILIZER | ||
Granular | 3-5 | 2,4 m – 3 m |
Pelleted | 3-5 | 3 m – 3,6 m |
GRASS SEED | ||
Fine | 3-4 | 1,8 m – 2,1 m |
Coarse | 4-5 | 2,4 m – 2,7 m |
ICE MELTER | 6-8 | 3 m – 3,6 m |
IMPORTANT: Minor setting adjustments may be necessary to compensate for the humidity and moisture content of the material.
MAINTENANCE
- Oil the free-spinning wheel once a year or more often as needed.
- Oil the nylon bushings in the frame tube once a year or more often as needed.
- Apply a light coating of grease to the gears as needed.
- Before each use makes a thorough visual check of the spreader for any bolts and nuts which may have loosened. Retighten any loose bolts and nuts.
- Make sure the tires are adequately inflated. Do not inflate beyond the maximum pressure printed on the tire.
WARNING: Over-inflated tires can explode, causing serious injury. To avoid injury, NEVER inflate tires beyond the maximum pressure printed on the sidewall of the tire. ALWAYS use a hand pump to safely inflate tires.
STORING
- Empty the spreader after each use, storing left over material in its original bag.
- Rinse the inside of the hopper and the exterior of the spreader and dry them off before storing.
- Store in a clean, dry area.
the fastest way to purchase parts
www.speedepart.com
Customer Care
M-F 7:00 a.m. – 5:00 p.m. CST
800-448-9282
www.agri-fab.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>