BORMANN BCG1500 Construction Material Grinder Instruction Manual
- June 9, 2024
- BORMANN
Table of Contents
BORMANN BCG1500 Construction Material Grinder Instruction
Operating Instructions
Important Instructions
Important instructions and warning notices are allegorated on the machine by
means of symbols: During work you should wear goggles, ear protectors, dust
mask, protective gloves and sturdy work clothes.
Technical Characteristics
Scouring Machine
- Frequency Load Speed: 40-60 Hz 4500rpm
- Max Milling Head Diameter 140 mm
- Collet: M10, female thread
- Protection Class: II
- Degree of Protection: IP 20
- Net Weight: Approx. 4.5 kg
Supply
Scouring Machine with milling head, Allen key and operating instructions in a metal case
Application for Indented Purpose
The Scouring Machine is indented for professional use With its milling head, the tool is intended to be used to remove loose plaster, glue and old paints in combination with an industrial vacuum cleaner.
Safety Instructions
Safe work with the machine is only possible if you read this operating
instruction and the safety instructions completely and follow the instructions
contained strictly. Additionally, the general safety instructions of the
leaflet supplied with the tool must be observed. Prior to the first use, the
user should absolve a practical training.
If the mains cable gets damaged or cut during the use, do not touch it, but
instantly pull the plug out of the socket.Never use the tool with damaged
mains cable. The tool must neither be wet nor used in humid environment.
- Do not use the tool near explosive materials (petrel, dilution).
- Do not work with materials containing asbestos
- Prior to every use, check the tool and its cable and plug. Have damages only repaired by specialists, Insert the plug into the socket only when the tool switch is off.
- Plug and switch the machine off if it is not under supervision, in case of putting up and stripping down the machine, in case of voltage drop or when fixing or mounting an accessory
- Switch the machine off if it stops for whatever reason You avoid that it starts suddenly and not under supervision.
- Before starting your work, check the proper seat of the cutting bit and the individual stars
- Check the milling head before every use. Do not use damaged or sluggishly running milling stars.
- Make sure that the tool was mounted properly, and let it run idly in a safe position for 30 seconds. Stop the tool immediately if you found considerable vibrations or other defects
- Don’t use the machine if a part of the housing is damaged or in case of damages on the switch, the cable or plug.
- Electrical tools have to be inspected visually bya specialist in regular intervals
- After interruption of your work, restart the tool only after having made sure that the milling head and the stars are moving freely.
- Do not touch rotating parts
- Persons under 16 years are not supposed to use the tool.
- Keep the handles dry, clean and free of oil and grease.
Retooling
Attention!
- Pull out the mains plug before retooling.
- The cutting stars may be hot.
- Wear protective gloves!
Change only the milling stars. In case of damage, the capstan may be replaced only in an authorized service center.
Remove the three wing screws from the height adjustment (refer to following
section). Remove the brush rim and the height adjustment. Open the Allen screw
M8 O using the supplied size 6 Allen key. Attentionl The screws have left-hand
thread. Holding the bush for the capstan with the stars@and the thrust
washers0. Put the new stars on. Fix the component parts refering to the
drawing
Attention! Use only Allen screws with locking fastener. Dust occurrence
during milling may lead to sticking of the stars. This will result in reduced
milling performance and increased wearing. Make sure that the stars are moving
freely and, if sticked, unbind them using a suitable tool (e.g pliers).
Attention! The milling stars might be hot
Height Adjustment
The machine includes a height adjustable protective hood
- Open the three wing nuts
- Pull the brush rim down till the depth gauge can be turned
- Adjust the required milling depth
- Push the brush rim up again
- Retighten the wing nuts
Dust Exhaust
Dust which occurs during your work is hazardous to health. That is why it is
advisable to use a coanar deduster and to wear a dust mask it should be
connected to a professional industrial vacUum
Care and Maintenance
Before the beginning of the maintenance or repair works you have to disconnect the plug from the mains, Repairs may be executed only by appropriately qualified and experienced personnel. elected specialist. Due to its design, the machine needs a minimum of care and maintenance. However, the following points have to be observed: After every repair the machine has to be inspected by an
- Always keep the power tool and the ventilation slots clean.
- During work, please pay attention that no particles get inside the machine,
- In case of failure, a repair has to be caried out by an authorized service workshop.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>