HATOR HTA-855 Ersatile Wireless Headset User Manual

HYPERPUNK
WIRELESS TRI -MODE
User
Manual

HTA855 (Back/Whikey
HTA-857 (Black/Yellow)
HTA-35 (Black/Mint)
HTA.859 (BlackLilac)

In the box

1. HATOR Hyperpunk Wireless Tri-mode headset
2. 2.4GHz dongle
3. 2m detachable USB-A to USB Type-C charging cable
4. 1m audio cable Type-C to 3.5mm
5. Detachable microphone
6. POP filter
7. Two rubber plugs for the microphone socket
8.  User manual

Specifications

Headset

Drivers:| 40mm with neodymium magnets
Impedance:| 17Q ±15%
Sensitivity:| 106dB ±3dB
Frequency response:| 10Hz-22kHz
Max. power:| 20mW
Connection t ype:| Wireless (Bluetooth and 2.4GHz)
Wired (USB and 3.5mm)
Sound delay in 2.4GHz mode:| <24ms
Sound delay in Bluetooth mode:| <8Oms
Operating time in 2.4GHz mode:| 23 hours
Operating time in Bluetooth mode:| 26 hours
Charging time:| 3 hours
Battery capacity:| 600mAh
Microphone
Type:| 6mm2.7mm omnidirectional
Frequency response:| 100Hz-10kHz
Signal-to-Noise ratio:| >64dB
Sensitivity:| -42 ±3dB
General
Dimensions:| 83mm (W)175mm (L)*193mm (H)
Weight:| 180 ±5g

Ergonomics and Controls

Wire mode

1. Connect the Type-C cable to the headset. Press and hold the power button to turn on the headset.The headset will be in wired mode at this time.(After connecting the Type-C cable in Bluetooth mode, the headset will only be charging. In 2.4GHz mode, connecting the Type-C cable will automatically change the playback mode to wired mode.Disconnecting the cable will return the headset to 2.4GHz wireless mode).
2. Short and long clicks on the volume control buttons will carry out the usual functions (turn the volume down or up).
3. The microphone will be turned on by default. To mute the microphone, press the microphone button on the headphones once. To activate the microphone, press the same button again.
4. By default, the headset will operate in stereo playback mode. A quick double-click on the microphone button will activate the virtual 7.1 sound mode.To return to stereo mode, press the same button twice.

Connection with a Type-C 3.5mm wire

1. Using a headset via a 3.5mm wire connection does not require it to be turned on.
2. In this mode, the volume, Play/Pause buttons, microphone control, etc. do not work.

2.4GHz wireless mode (game mode) Headset and transmitter combination

1. Turn off the headset and disconnect the transmitter.
2. Press the power button on the headset to turn it on, the light indicator will slowly start to light up. After that, press the power button two more times to put the headset in Game mode.
3. Connect the transmitter to the desired device (Computer, Game Console, etc.).
4. Press and hold the microphone button for 3 seconds to initiate the connection. After the connection is made, you will hear a notification that Game Mode has been activated. (Usually the headset and the transmitter are already connected).
5. The headset and the transmitter will be automatically connected after all actions. The light indicator will stay lit all the time.

How to use

1. Connect the transmitter to the desired device (Computer, Game Console, etc.), the light indicator will start to light up.
2. Turn on the headset and it will automatically connect to the transmitter. The indicator will light up permanently if the connection has been made. (If the headset could not detect a transmitter, perform the connection).
3. Short and long clicks on the volume control buttons will perform usual functions (turn the volume down or up).
4. The microphone will be turned on by default. To mute the microphone, press the microphone button on the headphones once. To activate the microphone, press the same button again.
5. By default, the headset will operate in stereo playback mode. A quick double-click on the microphone button will activate the virtual 7.1 sound mode. To return to stereo mode, press the same button twice. (More information is given in the table below).
6. When the headset battery is almost discharged (3.3V), the headset light indicator will blink red and the indicator on the transmitter will blink blue. If charging is not done in time, the headphones will automatically turn off.

2.4Ghz| “Button/feature/
Indicator”| Operation| Action| Information
---|---|---|---|---
2.4/Bluetooth
switch| Changing the type of
wireless connection| Double-click the power
button| The last mode is
remembered
Volume +| Volume up| Short press|
Long press|
The next track| Double click|
Volume –| Volume down| Short press|
Long press|
The previous track| Double click|
2.4GHz| “Button/feature/ Indicator”| Operation| Action| Information
---|---|---|---|---
Microphone button| Microphone on/off| Short press| Enabled by

default

Switching of sound modes (2.0/7.1)| Double click| 2.0 by default
2.4GHz pairing mode| Long press 3sec|
Microphone: 3.5mm| The microphone works when the microphone plug is inserted| Connect the 3.5mm 3pin audio plug|
Power button| Switching on| Long press 3sec|
Switching off| Long press 3sec|
Play/Pause| Short press|
Charge indicator| Red| Blinks while charging.
Turns off when charged|
Work indicator| Blue| Blinks after switching on. Lights up constantly after connection|
Type-C| Charging| Charging voltage SV Current up to 300mA| Overvoltage protection
Battery capacity 600mAh| Quick charge detection
Data transfer| Headset software update|
Wireless transmitter| USB-A plug| Plug and Play| Wireless 2.4GHz connection
Other| Button/feature/
Indicator| Operation| Action| information
---|---|---|---|---
Range| up to 10m| Without obstacles and gaps|
USB connection| 2.4GHz mode, connecting the USB cable automatcally activates the wired mode; disconnecting the cable automatically activates the wireless 2.4GHz mode
USB connection functions: the same as in the 2.4GHz mode; pairing and switching wireless modes are not available
3.5mm| Plug and play: The use of the headset, due to the connection via a 3.5mm wire, does not need to be turned on.
In this mode, volume buttons, Play/Pause, microphone control, etc. do not work.
Delay in 2.4GHz
“Game Mode”| 24ms
Low charge notifications| When the battery of the headset is almost discharged (voltage 3.3V), the light indicator of the headset will start flashing red, and the indicator on the transmitter will flash blue. If charging is not completed in time, the headphones will automatically turn off.
Energy saving
mode| The headset will automatically turn off after 10 minutes of no connection or audio signal.
Battery| 600mAh

Operation in Bluetooth mode

1. Turn on the headset, press the power button twice to switch to Bluetooth When the headset switches to Bluetooth-pair search mode, the indicator light will start blinking.
2. Hyperpunk headset is compatible with most Bluetooth-enabled smartphones and devices.
3. Turn on Bluetooth on your device and start searching for available Bluetooth devices.
4. Find the “HATOR Hyperpunk” headset in the list and connect to it. If the pairing has been successful, the indicator light will light up permanently.

(If the headset and device have already been paired, the headset will automatically connect to it as soon as it switches to Bluetooth mode)

Button functions: Call acceptance

One short click on the power button to answer the call. Important: Some smartphones may require additional settings.

End a call

One short click on the power button. Reject a call

Press and hold the power button for 1.5 sec. Music playback

1. Play/Pause: short click of the power button
2. Previous song: Double click of the “Volume-” button
3. Next song: Double click of the “Volume-F” button
4. Volume up: Short and long click of the “Volume-F” button
5. Volume down: Short and long click of the “Volume-” button

Bluetooth| Button/feature/ Indicator| Operation| Action| Information
---|---|---|---|---
2.4/Bluetooth switch| Changing the type of wireless
connection| Double-click the power button| The last mode is remembered
Volume +| Volume up| Short press|
Long press|
The next track| Double click|
Volume –| Volume down| Short press|
Long press|
The previous track| Double click|
Bluetooth| Button/feature/
Indicator| Operation| Action| Information
---|---|---|---|---
Microphone button| Microphone on/off| Short press| Enabled by default
Microphone: 3.5mm| The microphone works when the
microphone plug is inserted| Connect the 3.5mm 3pin audio plug|
Power button| Switching on| Long press 3sec|
Switching off| Long press 3sec|
Answer/End call| Short press|
Reject the call| Long press 1.5sec|
Charge indicator| Red| Blinks while charging. Turns off when
charged|
Status indicator| Blue| Blinks after switching on. Lights up constantly after connection|
Type-C| Charging| Charging voltage 5V Current up to 300mA| Overvoltage protection
Battery capacity 600mAh| Quick charge detection
Data transfer| Headset software update|
Charging| Headset is off while charging
Bluetooth version| V5.2| Name: HATOR Hyperpunk|
Other| Button/feature/
Indicator| Operation| Action| Information
---|---|---|---|---
Range| up to 10m| Without obstacles
and gaps|
Bluetooth latency| 80ms
Low charge notifications| When the battery of the headset is almost discharged (voltage 3.3V), the light indicator of the headset will start flashing red, and the indicator on the transmitter will flash blue. If charging is not completed in time, the headphones will automatically turn off.
Energy saving mode| The headset will automatically turn off after 10 minutes of no connection or audio signal.
Battery| 600mAh

System requirements
Wired use: devices with a 3.5mm audio jacks or USB
Wireless use: USB or Bluetooth devices
System compatibility
PC / MAC / MOBILE / GAMING CONSOLES / SOUND EQUIPMENT Platforms Windows 10, 11 / Mac OS / iOS / Android / Linux / PS / Xbox
Manufacturer’s warranty
Provided that the user observes the rules of operation, and taking into account the warnings set forth in this user manual, the device is safe to use and does not cause harm to the environment and humans, as well as is suitable for operation. The device has a warranty period: 24 months from the date of purchase excluding the time of repair (subject to the rules of operation). The right to warranty is granted by filling in the information of the attached warranty card. For more information about the product, as well as for any questions or suggestions, please contact us at the address below. The warranty is provided in addition to the rights granted under local consumer laws. Its terms may vary in different countries. Please read the full warranty information to learn about your consumer rights and additional remedies provided under this product warranty..
Instructions for use:

• Product cannot be opened or modified
• Do not disassemble the device or attempt to service it
• If the product is in an environment whose temperature exceeds the permissible range, turn off the device and wait until the operating temperature stabilizes within the specified range
• Do not allow liquid to fall on the product
• Use the product only with certified signal sources

Violation of the operating rules may lead to the loss of the ability to operate the equipment and the loss of the warranty. If the product doesn’t work properly, contact HATOR support. The warranty is in addition to the rights granted under local consumer laws. Its conditions may differ depending on the country. Some forms of exercising consumer rights when ensuring product warranty obligations can be performed through retail outlets (including online stores), which, in turn, are fully responsible for compliance with consumer rights protection laws. Supplier / Importer in EU: HATOR Gaming B.V., Address: Prins Hendrikkade 21-E, 1012TL, Amsterdam, The Netherlands, sales@hator.gg Warranty period: 24 months
@2023 HATOR. All rights reserved. All registered trademarks are property of their respective owners.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>