GE Appliances TM4000 Truvitals Smart Non-Touch 2-In-1 Thermometer with Bluetooth User Guide

: June 4, 2024
: GE Appliances

GE Appliances TM4000 Truvitals Smart Non-Touch 2-In-1 Thermometer with

Bluetooth

To see this user guide in Spanish, German, or Italian, please visit www.truvitals.com or scan the QR code below

Safety Precautions

This thermometer is not meant to diagnose illness or take the place of your doctor. If you are experiencing symptoms of illness, contact your physician for further guidance.
Dispose of this thermometer responsibly and in accordance with local regulations.
Do not use this thermometer where flammable gases are present.
There are no user-serviceable parts inside the thermometer.
Do not attempt to repair the thermometer on your own.
Do not attempt to disassemble, overhaul, or modify this thermometer.
Remove the batteries from the thermometer if it will not be used for three (3) months or longer.
Inspect the thermometer before each use to make sure parts are not broken or missing.
This thermometer is designed to test your temperature and should not replace consulting your physician.
Keep this thermometer out of reach of children.
Dispose of old batteries responsibly and in accordance with local regulations.
Do not use this thermometer outside of the proper temperature conditions to ensure accurate readings.
Handle the thermometer with care and avoid dropping the thermometer to prevent inaccurate readings.
Do not dip or submerge the thermometer in water or other liquids.
Clean the thermometer using a soft, dry cloth only.
Do not use harsh detergents or liquids.
Keep the thermometer out of direct sunlight in a dry, dust-free environment.
Clean the thermometer sensor before each use to ensure accurate readings.
Do not put any protective sleeves on the thermometer as this may impact the accuracy of temperature readings.
Wait at least 30 seconds between readings to ensure accuracy.
Keep young children in the same environment for a few minutes before taking their temperature as their bodies react slowly to environment changes.
For the most accurate reading on children 3 and under, it is recommended to take three (3) temperature readings and use the highest measurement.
Batteries may leak harmful liquids or ignitable materials which can result in an explosion that causes injury or damage to the product.
Do not mix old, new, or other types of batteries together.

FCC Regulatory Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference , and (2) this device must accept any interference received, including interference that may cause undesired operation.

Intended Use

The Truvitals Smart Non Touch 2-in-1 Thermometer with Bluetooth® is a battery- operated electronic device with intended use of measuring body temperature through touchless contact by means of an infrared sensor coupled with electronic signal amplification, conditioning, and a digital LED display. The device is reusable and intended for home use on people at all ages.

Features

View temperatures from your phone with Bluetooth connectivity.
Accurate temperature readings in just 1 second.
No contact readings to avoid the risk of contamination.
Fever alerts help you identify potential health risks.
Surface mode provides temperature readings of objects.
Easy to read LED display.
Memory feature records up to 32 measurements.
Pre-calibrated thermometer is ready to use out of the box.
15-second auto shutoff to preserve battery life.

Package Contents

Smart Non-Touch 2 in 1 Thermometer with Bluetooth
AAA 1.5 V Batteries (x2)
User Guide

Product Overview

Thermometer Overview

LED Screen
°C/°F Mode Button
Measure Button
Memory/Mute Button
Handle
Battery Cover

Screen Overview

Body Mode Indicator
Surface Mode Indicator
°C/°F Mode
Temperature
Low Battery Icon
Mute Mode
Bluetooth

Operation Instructions

Body Mode Temperature Readings

Power on the thermometer by pressing the measure button.
Check that the body mode indicator is lit on the screen to the thermometer is in body mode.
Hold the thermometer 1-2 in.(3-5 cm) from the forehead and press the measure button.

Hold the thermometer 1-2 in.(3-5 cm) from the forehead and press the measure button. Hold the thermometer still during reading. A beep will indicate that the measurement is complete unless the device is in mute mode.

Once a temperature is taken, the temperature will display for five (5) seconds. After the temperature has finished displaying, the thermometer will revert to standby mode indicated by three (3) dashes on the LED screen. Simply press the measure button again to take a new temperature. To power off the thermometer, press and hold the measure button for five (5) seconds while the device is in standby mode or wait 15 seconds for the auto shutoff feature to power off the thermometer. NOTES
Environment changes can affect the accuracy of temperature readings. Before use, allow the thermometer to remain in one location without significant air temperature changes for 30 minutes. Wait at least 30 minutes after strenuous exercise before taking a temperature reading. Do not wear a hat and make sure there is no hair, sweat, or makeup on your forehead while taking temperature readings. To avoid human error, take multiple measurements and use the average temperature.

Fever Alerts

If a temperature reading is above the normal range, the thermometer will give you a fever alert. The table below outlines how the thermometer indicates fever alerts.

One Short Beep

Two Short Beeps

Three Short Beeps

Memory Feature

This thermometer automatically stores the last 32 body temperature measurements.
To view previous readings, press the memory button.
Press the memory button to scroll to the next stored measurement.
Before displaying the measurement, a number will display between 1 and 32 to indicate which
you are viewing.
Remove the batteries from the thermometer to clear the memory

Switching Between Fahrenheit and Celsius

This thermometer can display temperatures in either degrees Fahrenheit (°F) or degrees Celsius (°C). To switch the unit of temperature displayed, simply press the °C/°F button while in standby mode.

Mute Feature

To mute the thermometer, hold the memory/mute button for two to three (2 – 3) seconds. This will silence all alerts from the thermometer. To unmute the thermometer, simply repeat the process. An audio alert will indicate that the thermometer is unmuted.

NOTE
When the thermometer is powered on, it will remain in the last used setting.

Surface Mode

Temperature Readings

With the thermometer powered off, press and hold the measure and memory buttons at the same time for three (3) seconds. Check that the surface mode indicator is lit on the screen to confirm the thermometer is in surface mode.
Hold the thermometer 1-2 in. (3-5 cm) from the surface you wish to measure and press the measure button.
Hold the thermometer still during reading. A beep willindicate that the measurement is complete unless the device is in mute mode.
Once a temperature is taken, the temperature will display for five (5) seconds. After the temperature has finished displaying, the thermometer will revert to standby mode indicated by three (3) dashes on the LED screen. Simply press the measure button again to take a new temperature.
To power off the thermometer, hold the measure button for five (5) seconds or wait 15 seconds for the auto shut off feature to power off the thermometer.

NOTE
The thermometer will automatically default back to body mode each time it powers off.

Using the Truvitals App

This thermometer is compatible with devices running iOS 8.0 and above or Android 4.3 and above. Keep the thermometer within at least 10 feet of your device to get the best result in establishing and maintaining a proper connection.

Open the settings in your smartphone or other smart device and make sure Bluetooth is turned on.
Download the Truvitals App from the App Store or Google Play.
Open the Truvitals App and create a new account if you are using this app for the first time.
Press the measure button on the thermometer to power it on.
Once the app is open and device is on, the app and thermometer should automatically pair together.
The Bluetooth symbol in the app should turn green when pairing is complete.
If the app and thermometer don’t automatically pair together, go to your Bluetooth list in your phone settings and select the thermometer.
Once pairing is established, a message saying Thermometer connected will appear in the app.

Maintenance & Cleaning

Battery Replacement

When the batteries need to be replaced, a low battery icon will display on the screen. To change the batteries, follow the steps below.

Slide the battery cover down to open the battery compartment.
Remove the old batteries and dispose of them properly.
Insert two (2) new batterie aligning them with the polarities.
Slide the battery cover back into place before powering on the thermometer.

NOTE
Remove the batteries if the thermometer will not be in use for more than three (3) months.

Cleaning

To clean the thermometer, wipe it with a dry, soft cloth. If the thermometer is contaminated, use a cloth moistened with water and a mild detergent or clean it with 75% alcohol. Take care not to use an excessive amount of liquid when cleaning the thermometer as liquids can seep into the electronic parts and cause damage to the thermometer.

Storage

Store in a safe, dry place free from dust and direct sunlight. Keep this thermometer out of reach of children. If you are storing the thermometer for more than three (3)
months, remove the batteries and keep the thermometer in the original packaging.

Error Codes

Error Code	Code Meaning	Resolution

The batteries are low.

|

Replace the batteries.

H| Temperature reading is too high.| Make sure the thermometer is properly aligned with the surface you are trying to read.
L| Temperature reading is too low.| Make sure the thermometer is properly aligned with the surface you are trying to read.
EH| Environment temperature is too high.| Move the thermometer to an appropriate environment and keep it there for 30 minutes before attempting to read a temperature.
EL| Environment temperature is too low.| Move the thermometer to an appropriate environment and keep it there for 30 minutes before attempting to read a temperature.

Err

|

System error.

|

Move the thermometer to an appropriate environment before trying again. If the problem persists, contact customer service.

No Display| The batteries are dead.| Replace the batteries.

Specifications

Operating Specifications

Body measurement range: 89.6 °F 109.4 °F (32 °C – 43 °C)
Surface measurement range: 0 °F 199.9 °F (0 °C – 93.2 °C)
Resolution: 0.1 °F (0.1 °C)
Response time: 1 sec
Time displayed on screen: 15 sec
Memory capacity: 32 readings
Thermometer Specifications
Dimensions (W x H x D): 1.4 x 5.5 x 1.7 36 x 140 x 42 mm
Weight (with batteries): 2.75 oz 78 g
Power supply: 2x AAA 1.5 V batteries
Display type: LED

Operating Environment

Temperature: 50 °F – 104 °F (10 °C – 40 °C)
Humidity: ≤ 85% RH
Atmospheric pressure: 70 kPa ~ 106 kPa

Storage Environment

Temperature: -4 °F – 131 °F (-20 °C – 55 °C)
Humidity: ≤ 93% RH
Atmospheric pressure: 70 kPa ~ 106 kPa
General Specifications
Product type: Thermometer
Power source required: Yes (battery powered)
Bluetooth function: Yes
Location: Indoor or outdoor use
Installation required: No
Adult assembly required: No
Additional tools required: No
Country of origin: China
Warranty included: Yes
Warranty length: 1 year

Warranty
LIMITED WARRANTY TO ORIGINAL CONSUMER
This Truvitals Smart Non-Touch 2 in 1 Thermometer with Bluetooth Product , including any accessories included in the original packaging, as supplied and distributed new by an authorized retailer is warranted by C&A Marketing, Inc. the Company to the original consumer purchaser only, against certain defects in material and workmanship Warranty as follows

To receive Warranty service, the original consumer purchaser must contact the Company orits authorized service provider for problem determination and service procedures. Proof of purchase in the form of a bill of sale or receipted invoice, evidencing that the Product is within the applicable Warranty period(s), MUST be presented to the Company or its authorized service provider in order to obtain the requested service. Service options, parts availability, and response times may vary and may change at any time.
In accordance with applicable law, the Company may require that you furnish additional documents and/or comply with registration requirements before receiving warranty service. Please contact our customer service for details on obtaining warranty service: 866-883-0022 info@truvitals.com Shipping expenses to the Company’s Return Facility are not covered by this warranty, and must be paid by the consumer. The consumer likewise bears all risk of loss or further damage to the Product until delivery to said facility.

EXCLUSIONS AND LIMITATIONS
The Company warrants the Product against defects in materials and workmanship under normal use for a period of ONE (1) YEAR from the date of retail purchase by the original end-user purchaser Warranty Period. If a hardware defect arises and a valid claim is received within the Warranty Period, the Company, at its sole option and to the extent permitted by law, will either (1) repair the Product defect at no charge, using new or refurbished replacement parts, (2) exchange the Product with a Product that is new or which has been manufactured from new or serviceable used parts and is at least functionally equivalent to the original device, or (3) refund the purchase price of the Product. A replacement Product or part thereof shall enjoy the warranty of the original Product for the remainder of the Warranty Period, or ninety (90) days from the date of replacement or repair, whichever provides you longer protection. When a Product or part is exchanged, any replacement item becomes your property, while the replaced item becomes the Company’s property. Refunds can only be given if the original Product is returned.

This Warranty does not apply to
Any non Truvitals Smart Non-Touch 2-in-1 Thermometer with Bluetooth product, hardware, or software, even if packaged or sold with the Product. Damage caused by use with non Truvitals Smart Non-Touch 2-in-1 Thermometer with

Bluetooth products

Damage caused by accident, abuse, misuse, flood, fire, earthquake, or other external causes;
Damage caused by operating the Product outside the permitted or intended uses described by the Company.
Damage caused by third party services.
A Product or part that has been modified to alter functionality or capability without the written permission of the Company;
Consumable parts, such as batteries, fuses, and bulbs;
Cosmetic damage.
If any Truvitals Smart Non-Touch 2-in-1
Thermometer with Bluetooth serial number has been removed or defaced.
This Warranty is valid only in the country where the consumer purchased the Product, and only applies to Products purchased and serviced in that country.
The Company does not warrant that the operation of the Product will be uninterrupted or error free.
The Company is not responsible for damage arising from your failure to follow instructions relating to its use.

NOTWITHSTANDING ANYTHING TO THE CONTRARY AND TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE COMPANY PROVIDES THE PRODUCT AS IS AND AS-AVAILABLE FOR YOUR CONVENIENCE AND THE COMPANY AND ITS LICENSORS AND SUPPLIERS EXPRESSLY DISCLAIM ALL WARRANTIES AND CONDITIONS, WHETHER EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, QUIET ENJOYMENT, ACCURACY, AND NON-INFRINGEMENT OF THIRD-PARTY RIGHTS. THE COMPANY DOES NOT GUARANTEE ANY SPECIFIC RESULTS FROM THE USE OF THE PRODUCT, OR THAT THE COMPANY WILL CONTINUE TO OFFER OR MAKE AVAILABLE THE PRODUCT FOR ANY PARTICULAR LENGTH OF TIME. THE COMPANY DISCLAIMS ALL WARRANTIES AFTER THE EXPRESS WARRANTY PERIOD STATED ABOVE. USE THE PRODUCT AT YOUR OWN DISCRETION AND RISK. YOU WILL BE SOLELY RESPONSIBLE FOR AND THE COMPANY DISCLAIMS) ANY AND ALL LOSS, LIABILITY, OR DAMAGES RESULTING FROM YOUR USE OF THE PRODUCT. NO ADVICE OR INFORMATION, WHETHER ORAL OR WRITTEN, OBTAINED BY YOU FROM THE COMPANY OR THROUGH ITS AUTHORIZED SERVICE PROVIDERS SHALL

CREATE ANY WARRANTY
IN NO EVENT WILL THE COMPANY’S TOTAL CUMULATIVE LIABILITY ARISING FROM OR RELATED TO THE PRODUCT, WHETHER IN CONTRACT OR TORT OR OTHERWISE EXCEED THE FEES ACTUALLY PAID BY YOU TO THE COMPANY OR ANY OF ITS AUTHORIZED RESELLERS FOR THE PRODUCT AT ISSUE IN THE LAST YEAR FROM YOUR PURCHASE. THIS LIMITATION IS CUMULATIVE AND WILL NOT BE INCREASED
BY THE EXISTENCE OF MORE THAN ONE INCIDENT OR CLAIM. THE COMPANY DISCLAIMS ALL LIABILITY OF ANY KIND OF ITS LICENSORS AND SUPPLIERS. IN NO EVENT WILL THE COMPANY OR ITS LICENSORS, MANUFACTURERS AND SUPPLIERS BE LIABLE FOR ANY INCIDENTAL, DIRECT, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES (SUCH AS, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF PROFITS, BUSINESS, SAVINGS, DATA, OR RECORDS) CAUSED BY THE USE, MISUSE, OR INABILITY TO USE THE PRODUCT. Nothing in these terms shall attempt to exclude liability that cannot be excluded under applicable law. Some countries, states, or provinces do not allow the exclusion or limitation of incidental or consequential damages or allow limitations on warranties, so certain limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may have other rights that vary from state to state or province to province. Contact your authorized retailer to determine if another warranty applies.