JOY QSG00075 HD Seat Bolt Mount Installation Guide
- June 4, 2024
- JOY
Table of Contents
JOY QSG00075 HD Seat Bolt Mount
Installation
Mount Installation
There are four different mounting options that can be utilized for securing
the mount to a vehicle bolt. There are a few things to consider when choosing
the best location for the bolt mount. When possible the arm at the base of the
mount should run perpendicular to the vehicle floor. This provides ultimate
support of the mount. Included are three bolt brackets along with a base that
should be utilized to accomplish this.
Choose the best option based on the hardware in the vehicle while ensuring
configuration provides optimal mount stability.
- (a) 90º raiser bracket x1
- (b) 90º bracket x1
- (c) 180º bracket x1
- (d) support bracket x1
- (e) washer x1
- (f) screw x1
- (g) screw nuts x2
- (h) support foot cap x1
- (i) base x1
- (j) support foot x1
Location 1: Flat Horizontal Surface
Remove the bolt from the vehicle.
Secure Base Using Vehicle Bolt: Replace bolt while securing the base (j).Attach Mount to Base: Place mount over base and secure by turning latch.
Attach Mount to Base: Place mount over base and secure by turning latch.
Location 2: Flat Horizontal Surface Obstructed Bolt
Secure Base to 180° Bracket. Ensure connection is tight.
Remove the bolt from the vehicle.
Attach Bracket with Bolt & Mount to Base: Replace the bolt while securing the bracket. Place mount over base and secure by turning latch.
Location 3: Flat Vertical Surface
Secure Base & Support Bracket to 90° Bracket. Ensure connection is tight.
Remove the bolt from the vehicle.
Attach Bracket with Bolt & Attach Mount to Base: Replace the bolt while securing the bracket. Place mount over base and secure by turning latch.
Location 4: Angeled Surface
Secure Base & Support Bracket to 45° Bracket. Ensure connection is tight.
Remove the bolt from the vehicle.
Attach Bracket with Bolt & Attach Mount to Base: Replace the bolt while securing the bracket. Place mount over base and secure by turning latch.
Tray Installation
Use Tray for Keyboard Case
Step 1: Place tray in a flat position. Fully expand brackets.
Step 2: Place keyboard on top of tray. Secure brackets tightly to edge of keyboard ensuring a tight
Extend & Rotate Arms:
Release the latch by pulling it away from the mount arm. Once released pull
the middle joint upward until it has reached desired position. Secure position
by turning latch to locking position. To rotate the arms & tray turn the knobs
at adjusting to your liking. Tighten knobs to secure.
DISCLAIMER FOR JOY FACTORY TABLET MOUNTS
Congratulations on the purchase of your new Tablet Mount from The Joy Factory
Inc!
BEFORE YOU INSTALL OR USE YOUR TABLET MOUNT, PLEASE READ ALL LITERATURE
PROVIDED WITH YOUR MOUNT TO ENSURE THE MOUNT YOU PURCHASED IS COMPATIBLE WITH
THE TABLET OR TABLETS YOU INTEND TO USE WITH THE MOUNT. IF YOU ARE NOT CERTAIN
WHETHER THE MOUNT IS COMPATIBLE WITH YOUR TABLET(S), PLEASE CHECK THE JOY
FACTORY WEBSITE OR CONTACT CUSTOMER SERVICE.
BEFORE YOU INSTALL OR USE YOUR TABLET MOUNT READ THIS DOCUMENT AND ALL
INSTRUCTIONS CAREFULLY. IMPROPER USE OF THE MOUNT WILL RESULT IN DAMAGE TO
YOUR TABLET. USE OF THE MOUNT WITH OTHER DEVICES MAY CREATE AN INSECURE
MOUNTING OF THE DEVICE, MAY PLACE UNANTICIPATED LOADS OR STRESS ON THE MOUNT
AND/OR WEAKEN THE MOUNT.
USE OF YOUR TABLET MOUNT WITH DEVICES OTHER THAN THOSE DEVICES FOR WHICH IT IS
DESIGNED WILL VOID ALL WARRANTIES FROM THE JOY FACTORY, WHETHER SUCH
WARRANTIES ARE EXPRESS OR IMPLIED. THE JOY FACTORS DISCLAIMS ANY AND ALL
LIABILITY FOR USE OF OUR MOUNTS WHEN IT IS NOT USED AS DESIGNED OR WHEN IT IS
USED FOR ANY PURPOSE OTHER THAN THE PURPOSE FOR WHICH IT IS DESIGNED.
THE JOY FACTORY SELLS VARIOUS MOUNTS FOR DIFFERENT USES OR APPLICATIONS. ONLY
USE YOUR Tablet MOUNT FOR ITS INTENDED PURPOSE AND ONLY WHEN AND WHERE IT IS
SAFE TO DO SO AND ONLY WHERE PERMITTED BY LAW.
The Joy Factory’s Tablet mounts are not intended to protect the electronics
used with the mounts from damage to, or loss or theft of, the Tablets. All
liability for damages or loss or theft of an electronic device used in
conjunction with The Joy Factory mounts is disclaimed and all warranties
relating to same, whether express or implied, are also disclaimed by The Joy
Factory.
Installation or attachment of any mounts from The Joy Factory must be done in
conjunction with the instructions provided by The Joy Factory and liability
for damage to the mounts or anything to which they are attached, and any
warranties, whether express or implied, are disclaimed by The Joy Factory.
For Mounts Used in Motor Vehicles:
FOR MOUNTS USED IN MOTOR VEHICLES, NEVER USE OUR MOUNTING DEVICE OR
ELECTRONICS WHILE OPERATING THE VEHICLE OR WHILE THE VEHICLE IS IN MOTION.
The Joy Factory disclaims any liability and all warranties, whether express or
implied, for use of its mounts in motor vehicles in any way which is not
allowed by law. The Joy Factory disclaims any liability and all warranties,
whether express or implied, for use of its mounts in any way which interferes
with the ability of the driver to operate the motor vehicle, distracts the
driver of the motor vehicle or is otherwise dangerous or reckless. The Joy
Factory will not pay for damages incurred or for citations, tickets or fines
issued due to improper mounting or use of its mounts.
For mounts used in vehicles, passengers in the vehicle should only use our
mounting device or electronic devices when it is safe to do so and only where
such use does not distract the operator of the vehicle or distract the
operator’s ability to safely operate the vehicle.
With respect to The Joy Factory mounts designed to mount to a vehicle
windshield via suction cup, it is critical to confirm whether such mounts are
legal in your state and, if so, any limitations on use of suction cup
attachments to windshields. Some states completely ban use of suction cup
mounts to windshields in motor vehicles. Some other states may allow use of
suction cup mounts to a vehicle’s windshield, but only in certain locations on
the windshield or in a manner which does not obstruct the driver’s vision or
otherwise distract the driver of the motor vehicle.
With respect to The Joy Factory mounts designed to mount to a vehicle’s seats using bolts, you are encouraged to hire a professional to install that mount. Installation of bolt-mounted devices from The Joy Factory must be done pursuant to instructions from The Joy Factory and from the manufacturer of your vehicle. Improper installation of a mounted device bolted to your vehicle’s seat may lead to the mount and/or the vehicle’s seat or other parts of the vehicle, being incapable of operating as intended. Any and all damages to your vehicle, the mount or any electronic device due to improper installation, whether by you, a professional or any other third party, is not the responsibility of The Joy Factory and The Joy Factory disclaims any and all such warranties, whether express or implied, for improper installation or use of bolt mounted devices.
The Joy Factory will replace your Tablet mount if it has any manufacturing defects, free of charge, for one year from the date of purchase. If you believe the mount has a manufacturing defect, cease use immediately and contact The Joy Factory by email at support@thejoyfactory.com or by telephone at 949-216-8888, Monday through Friday, 9:00 a.m. to 5:00 p.m., Pacific Time. Unfortunately, The Joy Factory is not able to replace or pay for replacement of Tablets or any additional items which may be damaged from use of a mount from The Joy Factory, whether the mount has or does not have manufacturing defects.
If your mount is damaged for any reason, or is not functioning properly for any reason, immediately stop using it. The Joy Factory expressly disclaims all liability and all warranties, whether express or implied, for use of one of its mounts that has been damaged for any reason. The Joy Factory will not replace a mount that is damaged, other than a mount with a manufacturing defect, nor will it replace, or pay for replacement of Tablets or any additional items which may be damaged due to use of a damaged or altered mount.
The Joy Factory disclaims all liability for lost or stolen mounts and any
device used with said mount.
Do not use your mount from The Joy Factory with any other Tablet case. Use of
an additional case may create an insecure mounting of the device, may place
unanticipated loads or stress on the mount and/or may weaken the mount and The
Joy Factory disclaims all liability from such use and will void any and all
warranties, express or implied.
Any alteration to your mount, or any part thereof, will void any and all
warranties and guarantees, whether express or implied, and The Joy Factory
disclaims any and all liability for damages arising from use of an altered
mount.
For full warranty information please visit thejoyfactory.com/warranty-
information.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>