VICTROLA VTA-204B 7-In-1 Turntable User Manual
- June 9, 2024
- Victrola
Table of Contents
VTA-204B 7-In-1 Turntable
User Manual
OVERVIEW
Top View
Back View
QUICK START GUIDE
FUNCTION KNOB – BASIC OPERATION
POWER ON /OFF: Turn the Function Knob to the left to turn the unit ON. Turn
the Function Knob to the middle to turn the unit OFF.
Note: The dial will illuminate solid white when turned ON. When the unit
is of the dial will not be illuminated.
VINYL STREAM: Turn the Function Knob to the right to connect the unit to an
external Bluetooth speaker.
Note: The dial will flash White when paired to a Bluetooth speaker. When
both devices are paired, the dial will be illuminated, White.
DUST COVER INSTALLATION
DUST COVER: Locate the plastic hinges in the accessory box. Slide the hinges
into the supports on the back of the turntable. Locate the dust cover and
match the unit hinges with the dust covers slots and slide the lid down into
the slot.
Note: When the unit is not in use, it is best to leave the lid covered.
SIMPLE SETUP
GETTING STARTED
Remove the needle cover, by gently pulling towards the front of the unit.
Carefully plug in the unit, install the platter, and tonearm weight.
Note: It is recommended that this product should be operated only from
the type of power source indicated on the rating label. This unit uses AC
power and is powered by a standard wall outlet.
CONNECTING THE SPEAKERS:
RCA LINE OUT : Use the red & white plugs on the back of the unit and
included RCA cables to connect to an amplifier/stereo device. Once connected,
switch ON the unit and the amplifier device you connected. Then adjust the
volume on the amplifier device.
SWITCHABLE PHONO PRE-AMP : This switch allows the internal stereo phono
pre-amp to be bypassed when the turntable is used with equipment that has
magnet phono inputs. Unless you are using equipment with magnetic phono
inputs, the switch should be set to “LINE”. Improper setting of the switch may
lead to no sound or loud unwanted feedback.
PLATTER INSTALLATION
| 
| 
---|---|---
PLACE THE PLATTER ON THE TURNTABLE. THE BELT IS PRE-INSTALLED UNDER THE
PLATTER| FIND THE GUIDE STRING TAPED
TO THE PLATTER AND CAREFULLY REMOVE THE TAPE WHILE HOLDING THE STRING| USE THE
STRING TO PULL THE
BELT OVER THE MOTOR PIN ONCE
BELT IS ON MOTOR PIN, DISCARD
THE GUIDE STRING
TONEARM SETUP
***IMPORTANT, THE TONE ARM MUST BE SET UP AS INSTRUCTED BELOW OR DAMAGE MAY OCCUR TO THE UNIT OR RECORDS.
| 
| 
---|---|---
IDENTIFY THE WEIGHT ON THE BACK OF THE TONEARM. USE THE INCLUDED 2.5MM HEX KEY TO LOOSEN THE SET SCREW| REMOVE THE NEEDLE COVER – LIFT THE TONEARM OUT OF THE HOLDER TO THE LEFT SO IT FLOATS FREELY – NOT TOUCHING ANYTHING| TURN THE COUNTERWEIGHT ON THE BACK OF THE TONEARM UNTIL THE TONE ARM IS FLAT AND BALANCED (SEE BOTTOM PICTURE)
| 
| 
SET ONLY THE “NUMBER” RING, SO “0” IS IN THE TOPMOST POSITION: DO NOT LET THE REAR WEIGHT TURN (NUMBER RING AND COUNTERWEIGHT MOVE SEPARATELY FROM EACH OTHER)| HOLDING BOTH THE NUMBER RING & COUNTERWEIGHT, ROTATE COUNTERCLOCKWISE 1 1/2 ROTATIONS UNTIL YOU END ON “1”, AND THAN
TIGHTEN SET SCREW| ONCE THE COUNTERWEIGHT IS SET, ADJUST THE ANTI-SKATE CONTROL
TO THE RECOMMENDED SETTING OF “1.5”
The purpose of the counterweight is to set the tonearm to 3 grams of downward
force, the recommended tracking weight for this cartridge. (One full
counterclockwise turn with the counterweight is equal to 2g, that is why you
continue to turn counterclockwise until “1”)
ANTI-SKATING ADJUSTMENT The anti-skating function helps compensate for
the inward tracking force that occurs with certain records when the stylus
(needle) nears the center or end of the record.
Once the counterweight is set, adjust the anti-skate control. For the included
cartridge, the recommended anti-skate setting should be “1.5”.
If you notice excessive skipping or tonearm pulling inward or outward, you can
adjust the anti-skate as needed.
VINYL PLAYING
VINYL: Playing a Vinyl record
Note: -Before using, make sure the tonearm is properly set up.
See the TONE ARM SETUP page.
Using the Function Knob, turn the knob to ON. (the dial will illuminate solid
white.)
Remove the needle cover, by gently pulling towards the front of the unit.
Select the proper record speed (see back of unit).
If using a 45 RPM record, use the included 45 adaptors.
Release the Tone Arm from the holder and gently place it on the record using
the lift lever.
Use your external device to control the volume.
Note:
- Make sure to only touch the center or edges of the record to avoid damage to the vinyl grooves.
- Do not adjust the counterweight while playing a record as this could break the needle and scratch the record.
- If no sound is playing, the unit may be in Vinyl Stream mode
The record will stop spinning automatically when playback is complete.
To stop manually, lift the tone arm from the record and return it to the rest.
VINYL STREAM
VINYL STREAM: Playing a Vinyl record on an external Bluetooth speaker or
headphones.
Simply turn the Function Knob to the “ ” to place it in Vinyl Stream mode
(the dial will flash white).
Turn ON your external Bluetooth speaker or headphone, and set it to pairing
mode.
Wait a few seconds for the unit to find your device.
The unit will illuminate solid white.
Use your external device to control the volume.
Note: -We recommend placing the Bluetooth device within 1m (3.3′) of the
product when initially pairing.
- Make sure the unit is within 10m (33ft) from your external device for the strongest connection.
- Vinyl Stream is only compatible with vinyl record playback.
- The product stays in the pairing mode for 30 seconds. If pairing is not
properly completed, follow the above steps again from the beginning after turning all devices OFF.
CARTRIDGE REPLACEMENT
REPLACEMENT CARTRIDGE: VICTROLA VPC-190
The VPC-190 Cartridge is rated in excess of 1000 hours of normal use. As soon
as you notice a change in sound quality or damage to the stylus, it is
recommended that it be changed.
- Unplug the unit and put the needle cover on the old cartridge.
- Carefully remove all the wire leads from the back of the old cartridge.
- Loosen the 2 Allen head screws with the included 2mm hex keys on the top of the tonearm/cartridge. Remove the old cartridge.
- Mount the new cartridge, adjust the position to ensure it will track parallel to the record grooves, and tighten the screws.
- Connect the wire leads to the new cartridge by pushing them firmly onto the connector pins.
| WHITE | Left channel positive | (L+) |
|---|---|---|
| RED | Right channel positive | (R+) |
| BLACK | Left and Right channels negative | (L- & R-) |
For best results, use a cartridge alignment protractor or download our Cartridge Alignment Protractor at victrola.com/cartridgealignment
SPECIFICATIONS
GENERAL
Power Requirements ………………………………………………… AC 100-240V~50/60HZ
Power Consumption ………………………………………………………. 6 W
Dimensions (W x D x H)…………………………………………….. 350mm x 420mm x 120mm (approx)
Weight ……………………………………………………………….. 4.81 kgs
RECORD PLAYER
Motor……………………………………………………………………. DC servo motor
Drive System………………………………………………………………. Belt Drive
Speeds …………………………………………………………………. Off/33-1/3 rpm, 45 rpm
Cartridge Type ……………………………………………………. Moving Magnetic Cartridge
Moving Magnetic Cartridge ………………………………………………. Victrola VPC-190
BLUETOOTH
Bluetooth Version ………………………………………………….. Bluetooth V5.0
Bluetooth Profiles ……………………………………………….. A2DP, AVRCP
Bluetooth Frequency range………………………………………….. 2.402GHz-2.480GHz
Operating Distance …………………………………………………..10 meters (33 ft.)
INCLUDED:
T1 Turntable & Dust Cover, 45 RPM Adapter, Silicone Slipmat, RCA Cable, Power
Cable, Instruction Manual, Quick Setup Guide, 2mm/2.5mm hex key, Dust Cover
Hinges
WARNING
Important Safety Instruction
-
Read these instructions – All the safety and operating instructions should be read before this product is operated.
-
Keep these instructions – The safety and operating instructions should be retained for future reference.
-
Heed all warnings – All warnings on the appliance and in the operating instructions should be adhered to.
-
Follow all instructions – All operating and use instructions should be followed.
-
Do not use this apparatus near water – The appliance should not be used near water or moisture – for example, in a wet basement or near a swimming pool, and the like.
-
Clean only with a dry cloth.
-
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
-
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
-
Protect the power cord from being walked on or pinched particularly at the plugs, convenience receptacles, and at the point where they exit from the apparatus.
-
Only use attachments/accessories specified by the manufacturer.
-
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
-
Unplug the apparatus during lightning storms or when unused for long periods of time.
-
Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus have been exposed to rain or moisture, do not operate normally, or has been dropped.
-
This lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of non-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
a. Warning: To reduce the risk of electric shock, do not remove the cover (or back) as there are no user-serviceable parts inside. Refer servicing to qualified personnel.
b. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the appliance. -
****This equipment is a Class II or double-insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to the electrical earth.
-
The mains plug is used as a disconnect device, the disconnect device shall remain readily operable.
-
WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall not be placed on the apparatus. -
The use of the equipment in a moderate climate.
-
WARNING: Please refer to the information on the exterior bottom/back enclosure for electrical and safety
information before installing or operating the apparatus. -
The ventilation should not be impeded by covering the ventilation openings with items such as newspaper, tablecloths, curtains, etc.
-
No naked flame sources, such as lighted candles, should be placed on the apparatus.
-
Do not install this equipment in a confined space such as a bookcase or similar unit.
SAFETY INFO
Safety Information
- In order to shut off power to this product completely, unplug the power cord from the wall outlet. Be sure to unplug the unit if you do not intend to use it for an extended period of time, such as during a vacation.
- Use of controls, adjustments, and performance of procedures other than those specified herein may result in hazardous radiation exposure.
- To prevent electric shock, match the wide blade of the plug to the wide slot, and fully insert it.
- If this product is experience problems during operation, contact qualified service centers, and do not use the product in defective states.
Before Use
-
Choose unit installation location carefully. Avoid placing it in direct sunlight or close to a source of heat.
Also avoid locations subject to vibrations and excessive dust, cold, or moisture. Keep away from sources that hum, such as transformers or motors. -
Do not open the cabinet as this may result in damage to the circuitry or electrical shock. If a foreign object should get into the set, contact Customer Service.
-
Be sure not to handle records with dirty fingers. Never play a record that has a crack on the surface.
-
When removing the power plug from the wall outlet, always pull directly on the plug, never pull the cord.
-
To protect the stylus, don’t forget to put on the white protective needle cover after use.
-
Do not attempt to clean the unit with chemical solvents as this might damage the finish. Use a clean, dry cloth.
-
In order to shut off the power to this product completely, unplug the power cord from the wall outlet. Be sure to unplug the unit if you do not intend to use it for an extended period of time, such as a vacation.
-
Keep this manual in a safe place for future reference.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
The device must not be co-located or operating in conjunction with any other
antenna or transmitter. To maintain compliance with the FCC’s RF exposure
guidelines, place the product at least 20cm from nearby persons.
WARRANTY
Victrola is a registered trademark of Innovative Technology Electronics,
LLC.
United States
Victrola (Innovative Technology Electronics, LLC) warrants to the original
retail purchaser that this product will be free from defective materials and
workmanship for one (1) year from the date of purchase, subject to the
limitations below. This warranty period is not extended if we replace the
product.
To obtain a replacement under the terms of this warranty, you must contact the
dealer from which it was purchased with your original receipt. If assistance
from the dealer from which it was purchased is impossible, you may contact our
customer service for warranty assistance at victrola.com/contact.
Except as limited below, if the product proves defective in either material or
workmanship within one (1) year from the date of purchase, Victrola will
replace the product at no charge. If the product model is no longer available
and cannot be replaced with an identical model, Victrola will issue a
merchandise credit
for the purchase price to be redeemed at victrola.com.
Limitations:
- This limited warranty does not cover failure of the product arising, in whole or in part, from improper installation, storage, transportation, misuse, abuse, accident, neglect, mishandling, unauthorized repair, modification, or wear from ordinary use or environmental deterioration.
• This limited warranty does not cover cosmetic damage, including paint damage, or consequential damage to other components or premises which may result for any reason from the failure of the product.
• This limited warranty is null and void for products not used in accordance with Victrola’s instructions.
• This limited warranty terminates if the original retail purchaser sells o otherwise transfers this product.
• This limited warranty is null and void for defects or damage caused by installation or repair performed by any person or entity other than a Victrola authorized installer or dealer.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state, jurisdiction to jurisdiction, or
country to country. All express and implied warranties for the product,
including but not limited to any implied warranties of merchantability and
fitness for a particular purpose, are limited in time to the term of this
warranty. Some states, jurisdictions, or countries do not allow the exclusion
of certain implied warranties or conditions, or limitations on how long an
implied warranty or condition lasts, so this limitation may not apply to you.
Victrola’s responsibility for malfunctions and defects in hardware is limited
to replacement or repair as set forth in this warranty statement. Victrola
does not accept liability for special, punitive, consequential, or incidental
damages or losses, whether direct or indirect, including without limitation,
any liability for third-party claims against you for damages or losses or for
products not being available for use. The maximum liability for which Victrola
may be responsible will be no more than the amount you paid for the product
that is the subject of the claim.
Some states, jurisdictions or countries do not allow the exclusion or
limitation of special, indirect, incidental, or consequential damages, so the
above limitation or exclusion may not apply to you.
Canada and US Territories
The Warranty on this product shall comply with applicable law when sold to a
consumer in Canada or a US Territory. To obtain any applicable warranty
service, please contact the dealer from which you purchased the product or the
distributor that supplied the product, with your original receipt.
If assistance from the dealer from which it was purchased is impossible, you
may contact our customer service for warranty assistance at
victrola.com/contact.
If this product proves defective in either material or workmanship, Victrola
will replace the product at no charge. If the product model is no longer
available and cannot be repaired effectively or replaced with an identical
model, Victrola at its sole option may replace the unit with a current model
of equal or greater value.
Outside the U.S, Canada, and US Territories
The Warranty on this product shall comply with applicable law when sold to a
consumer outside of the United States, Canada, and US Territories. To obtain
any applicable warranty service, please contact the dealer from which you
purchased the product or the distributor that supplied the product, with your
original receipt.
VPT1000-102621
Documents / Resources
|
VICTROLA VTA-204B 7-In-1
Turntable
[pdf] User Manual
VTA-204BTO, VTA204BTO, 2AFHW-VTA-204BTO, 2AFHWVTA204BTO, VTA-204B 7-In-1
Turntable, VTA-204B, 7-In-1 Turntable, Turntable
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>