ASRock PG27F15RS1A Curved Gaming Monitor User Manual
- June 9, 2024
- ASRock
Table of Contents
- Chapter 1 Introduction
- Chapter 2 Specifications
- Chapter 3 Monitor Overview
- Chapter 4 Adjusting the Viewing Angle
- Chapter 5 Connecting the Monitor
- Chapter 6 OSD Setup
- Chapter 7 Troubleshooting
- Chapter 8 Safety Instructions
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ASRock PG27F15RS1A Curved Gaming Monitor
Chapter 1 Introduction
Thank you for purchasing PG27F15RS1A, a reliable monitor produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance.
Package Contents
- ASRock PG27F15RS1A Monitor Head
- ASRock PG27F15RS1A Stand
- ASRock PG27F15RS1A Quick Start Guide
- DisplayPort Cable (DisplayPort to DisplayPort)
- HDMI Cable
- Power Cord
⚠ Important
Contact your place of purchase or local distributor if any of the items is
damaged or missing.
Package contents may vary by country.
The included power cord is exclusively for this monitor and should not be used with other products.
Installation Instructions
Leave the monitor in its protective foam packaging. Align the latches of the stand to the monitor. Tighten the stand with screws.
Connect the stand base to the stand and tighten the screw to secure the stand base.
Align the latches to place the stand cover.
Adjust the angle of the stand, make sure the stand assembly is properly installed before setting the monitor upright.
⚠ Important
Remove the screws on the monitor groove if needed before installing the stand.
Place the monitor on a soft, protected surface to avoid scratching the display
panel.
Do not use any sharp objects on the panel.
The groove for installing the stand bracket can also be used for wall mount. Please contact your dealer for proper wall mount kit.
UNPACKING
INSTALLING THE STAND ARM
ATTACHING THE BASE & TIGHTENING THE SCREW
1/0PORTS
CONNECTING CABLES
CONNECTING THE MONITOR TO A PC
*Use either the HDMI or DisplayPort connection for display.
POWERING ON
ADJUSTING THE TILT ANGLE
ADJUSTING THE SWIVEL ANGLE
Chapter 2 Specifications
Monitor specifications
Monitor | ASRock PG27F15RS1A |
---|---|
Size | 27 inch |
Curvature | 1500R |
Panel Type | VA |
Resolution | 1920 x 1080 |
Digital Signal Frequency | HDMI: 30KHz~255KHz (H); 48Hz~240Hz (V) |
DisplayPort: 30KHz~255KHz (H); 48Hz~240Hz (V)
Aspect Ratio| 16:9
Brightness (nits)| 300(Typ.)
Contrast Ratio| 3000:1(Typ.)
Refresh Rate| 240Hz(Max.)
Response Time| 1ms(MPRT), 6ms(GTG)
I/O Ports| 1DisplayPort™ 1.2
2HDMI™ 2.0
1*Earphone Jack(3.5 mm)
View Angles| 178°(H) / 178°(V)
Color Space| 90% DCI-P3 / sRGB 113%
Surface Treatment| Anti-Glare
Display Colors| 16.7M
Monitor Power Options| 100~240Vac, 50/60Hz, 1.5A
Power Consumption| Power On(Max) ≦ 70W; Power Saving: ≦0.5W; Power Off: ≦0.3W
Adjustment (Tilt)| +23° ~ -5°
Adjustment (Swivel)| +20° ~ -20°
VESA Mounting|
- Plate Type: 100 x 100mm
- Screw Type: M4 x 10 mm
Dimension (W x H x D)| Dimension with Stand: 610.34457.91192.61mm
Dimension without stand:
610.34367.3479.65mm
Weight| 5.11 Kg (With Stand)
4.40 Kg (Without Stand)
Environment| Operating
- Temperature: 0℃ to 40℃
- Humidity: 10% to 85%, noncondensing
- Altitude: 0 ~ 3658m Storage
- Temperature: -20℃ to 60℃
- Humidity: 5% to 80%, non-condensing
- Altitude : 0~12192m
Preset Display Modes
Standard | Resolution | PG27F15RS1A | Remark |
---|---|---|---|
HDMI | DP | HDR | |
IBM MODE DOS | 720×400 @70Hz | V | V |
VGA | 640×480 @60Hz | V | V |
640×480 @67Hz | V | V | |
640×480 @72Hz | V | V | |
640×480 @75Hz | V | V | |
SVGA | 800×600 @56Hz | V | V |
800×600 @60Hz | V | V | |
800×600 @72Hz | V | V | |
800×600 @75Hz | V | V | |
XGA | 1024×768 @60Hz | V | V |
1024×768 @70Hz | V | V | |
1024×768 @75Hz | V | V | |
SXGA | 1280×1024 @60Hz | V | V |
1280×1024 @75Hz | V | V | |
WXGA+ | 1440×900 @60Hz | V | V |
WSXGA+ | 1680×1050 @60Hz | V | V |
1152×864 @75Hz | V | V | |
1280×960 @60Hz | V | V | |
1280×720 @60Hz | V | V | |
Full HD | 1920×1080 @60Hz | V | V |
(Default)
1920×1080 @100Hz| V| V| V| DTD
1920×1080 @120Hz| V| V| V| DTD
1920×1080 @144Hz| | | | DTD
1920×1080 @165Hz| V| V| V| DTD
1920×1080 @240Hz| V| V| V| DTD
QHD| 2560×1440 @60Hz| | | |
2560×1440 @120Hz| | | |
2560×1440 @144Hz| | | |
2560×1440 @165Hz| | | |
WQHD| 3440×1440 @60Hz| | | |
3440×1440 @120Hz| | | |
3440×1440 @144Hz| | | |
3440×1440 @165Hz| | | |
UHD| 3840×2160 @60Hz| | | |
3840×2160 @120Hz| | | |
3840×2160 @144Hz| | | |
Video Timing Resolution| 640x480P 59.94/60Hz
4:3
| V| V| |
720x480P 59.94/60Hz
4:3
| | | |
720x480P 59.94/60Hz
16:9
| V| V| |
720x576P 50Hz 4:3| | | |
720x576P 50Hz 16:9| V| V| |
1280x720P 50Hz 16:9| V| V| |
1280x720P 59.94/60Hz
16:9
| V| V| |
1920x1080P
59.94/60Hz 16:9
| V| V| V|
1920x1080P
119.88/120Hz 16:9/1:1
| V| V| V|
2160P @25Hz| | | |
2160P @30Hz| V| | |
2160P @50Hz| V| | V|
2160P @60Hz| V| | V|
2160p @120Hz| | | |
Chapter 3 Monitor Overview
Front view
No. | Item | LED Indication |
---|---|---|
1 | Power Indicator |
- Blue – Power on mode
- Orange – Standby mode
- LED Off – Off mode
Back side
No. | Description |
---|---|
2 | Power and OSD Keys |
3 | Serial Label |
4 | Cable Management Slot |
5 | Built-in Speakers (2x2W) |
Bottom Side
No. | Item |
---|---|
6 | AC input |
7 | HDMI input |
8 | HDMI input |
9 | DisplayPort input |
10 | Audio output |
Chapter 4 Adjusting the Viewing Angle
For optimal viewing, it is recommended to look at the full face of the
monitor, and then adjust the monitor’s angle to your own preference.
Hold the stand so you do not topple the monitor when you adjust the monitor’s
angle.
You are able to adjust the tilted angle from -5° to 23°.
⚠ Important
Avoid touching the display panel when adjusting the monitor. You are able to
swivel the monitor for the angle.
NOTE:
Do not touch the LCD screen when you adjust the angle. It may cause damage or
break the LCD screen.
Careful attention is required not to catch your fingers or hands when you
adjust the angle.
Chapter 5 Connecting the Monitor
- Turn off your computer.
- Connect the video cable from the monitor to your computer.
- Connect the power cord to the monitor power jack.
- Plug the power cord into the electrical outlet.
- Turn on the monitor.
- Power on the computer and the monitor will auto detect the signal source.
- Plug one end of the DisplayPort/HDMI cable to the monitor’s DisplayPort/HDMI port.
*Use either the HDMI or DisplayPort connection for display. - Connect the other end of the DisplayPort/HDMI cable to your computer’s DisplayPort/HDMI port.
Chapter 6 OSD Setup
This chapter provides you with essential information on OSD Setup.
⚠ Important
All information is subject to change without prior notice.
OSD Keys
The monitor comes with OSD Keys that help navigate the On-Screen Display (OSD)
menu.
No. | Item | Description |
---|---|---|
1 | Navi Key | A multi-directional control that helps navigate the On- |
Screen Display (OSD) menu.
2| Preset Modes| Activates the Presets Modes function when the OSD is
OFF, navigate through adjustment icons when OSD is ON, or adjust a function
when function is activated.
3| Brightness| Adjusts the backlight when the OSD is OFF.
4| Power| Press the power button to turn on/off the monitor.
OSD Menus (The descriptions for function control)
Function: Luminance
Main Menu Item| Sub Menu Item| Sub Menu|
Description
---|---|---|---
Luminance| Contrast| 0-100| Contrast from Digital-register.
Brightness| 0-100| Backlight Adjustment
Preset Modes| Standard| Standard Mode
Text| Text Mode
Internet| Internet Mode
Game| Game Mode
Movie| Movie Mode
Sports| Sports Mode
DCR| On| Dynamic contrast ratio
Off
MPRT| On| MPTRT function On/Off
Function: Image Setup
Main Menu Item | Sub Menu Item | Sub Menu | Description |
---|---|---|---|
Image Setup | Image Ratio | Full | Select Image Aspect Ratio |
Aspect
OD| On| Overdrive Adjustment
Off
Adaptive Sync On or Off| On| Adaptive Sync On or Off
Off
HDR| Auto| HDR Auto or Off
Function: Color Temp
Main Menu Item| Sub Menu Item| Sub Menu|
Description
---|---|---|---
Color Temp.| Warm| ─| Recall Warm Color Temperature from EEPROM.
Normal| ─| Recall Normal Color Temperature from EEPROM.
Cool| ─| Recall Cool Color Temperature from EEPROM.
User| Red| Red Gain from Digital- register.
Green| Green Gain from Digital-register.
Blue| Blue Gain from Digital- register.
sRGB| ─| Recall sRGB Color Temperature from EEPROM.
Low Blue Light| 0~10(Level)| Phantom Gaming
Monitor with ASRock
Low Blue Light Technology reduces the emission of harmful blue lights on a display to prevent eye fatigue.
Function: OSD Setup
Main Menu Item| Sub Menu Item| Sub Menu|
Description
---|---|---|---
OSD Setup| H. Position| 0-100| Adjust the horizontal position of OSD
V. Position| 0-100| Adjust the vertical
position of OSD
Timeout| 5-100| Adjust the OSD Timeout
Language| ─| Select the OSD language
Function: Extra
Main Menu Item| Sub Menu Item| Sub Menu|
Description
---|---|---|---
Extra| Input Select| Auto| Select input source
HDMI1
HDMI2
DisplayPort
DDC/CI| On or Off| Turn ON/OFF DDC/CI Support
Reset| Yes or No| Reset the menu to default.
Information| ─| Show the information of the main image source.
Chapter 7 Troubleshooting
Problem and Question | Possible Solution |
---|---|
Power LED is not on |
- Check if the Power Switch is in the ON position.
- Power Cord should be connected.
No signal|
- Check that the signal-cable is properly connected. If the connector is loose, tighten the connector’s screws.
- Check the signal-cable’s connection pins for damage.
Picture is fuzzy|
- Adjust the Contrast and Brightness Controls.
Picture bounces or a wave pattern is present in the picture|
- Move electrical devices that may cause electrical interference.
The power LED is ON (Orange) but there’s no video or no picture.|
- Computer Power Switch should be in the ON position.
- Computer Video Card should be snugly seated in its slot.
- Make sure Monitor’s video cable is properly connected to the computer.
- Inspect Monitor’s video cable and make sure none of the pins are bent.
- Make sure computer is operational by hitting the CAPS LOCK key on ,the keyboard while observing the CAPS LOCK LED. The LED should either turn ON or OFF after hitting the CAPS LOCK key.
Missing one of the primary colors (RED, GREEN, or BLUE)|
- Inspect the Monitor’s video cable and make sure that none of the pins are bent.
Picture has color defects (white does not look white)|
- Adjust RGB color or select color temperature.
Poor brightness or contrast|
- When the brightness of the screen lowers after being used for a certain period and the function of the display is affected, send it to our authorized service center for repair.
Unable to open OSD menu.|
- Turn off your monitor, unplug the power cord and plug it back in, then power on the monitor.
- Check if the OSD menu is locked? If so, please press and hold the Navi Key for 5~6 seconds to unlock the OSD menu.
Chapter 8 Safety Instructions
- Read the safety instructions carefully and thoroughly.
- All cautions and warnings on the device or User Guide should be noted.
- Refer servicing to qualified personnel only.
Power
- Make sure that the power voltage is within its safety range and has been adjusted properly to the value of 100~240V before connecting the device to the power outlet.
- If the power cord comes with a 3-pin plug, do not disable the protective earth pin from the plug. The device must be connected to an earthed mains socket-outlet.
- Please confirm the power distribution system in the installation site shall provide the circuit breaker rated 120/240V, 20A (maximum).
- Always disconnect the power cord or switch the wall socket off if the device would be left unused for a certain time to achieve zero energy consumption.
- Place the power cord in a way that people are unlikely to step on it. Do not place anything on the power cord.
- If this device comes with an adapter, use only the ASRock provided AC adapter approved for use with this device.
European Union:
Batteries, battery packs, and accumulators should not be disposed of as
unsorted household waste. Please use the public collection system to return,
recycle, or treat them in compliance with the local regulations.
California, USA:
The button cell battery may contain perchlorate material and requires special
handling when recycled or disposed of in California. For further information
please visit: https://dtsc.ca.gov/perchlorate/
Environment
- To reduce the possibility of heat-related injuries or of overheating the device, do not place the device on a soft, unsteady surface or obstruct its air ventilators.
- Use this device only on a hard, flat and steady surface.
- To prevent the device from tipping over, secure the device to a desk, wall or fixed object with an anti-tip fastener that helps to properly support the device and keep it safe in place.
- To prevent fire or shock hazard, keep this device away from humidity and high temperature.
- Do not leave the device in an unconditioned environment with a storage temperature above 60℃ or below -20℃, which may damage the device.
- The maximum operating temperature is around 40℃.
- When cleaning the device, be sure to remove the power plug. Use a piece of soft cloth rather than industrial chemical to clean the device. Never pour any liquid into the opening; that could damage the device or cause electric shock.
- Always keep strong magnetic or electrical objects away from the device.
- If any of the following situations arises, get the device checked by service personnel:
- The power cord or plug is damaged.
- Liquid has penetrated into the device.
- The device has been exposed to moisture.
- The device does not work well or you can not get it working according to the User Guide.
- The device has dropped and damaged.
- The device has obvious sign of breakage.
Warning!
Overuse of screens is likely to affect eyesight.
Recommendations:
Take a 10-minute break for every 30 minutes of screen time. Children under 2
years of age should have no screen time. For children aged 2 years and over,
screen time should be limited to less than one hour per day.
CE Conformity
This device complies with the requirements set out in the Council Directive on
the Approximation of the Laws of the Member States relating to Electromagnetic
Compatibility (2014/30/EU), Low-voltage Directive (2014/35/EU), ErP Directive
(2009/125/EC) and RoHS directive (2011/65/EU). This product has been tested
and found to comply with the harmonized standards for Information Technology
Equipment published under Directives of Official Journal of the European
Union.
SRock Contact Information
ASRock EUROPE B.V.
Address : Bijsterhuizen 11-11, 6546 AR Nijmegen,The Netherlands
Phone: +31-24-345-44-33
Technical Support
Phone: +31-24-345-44-33
Online Support https://event.asrock.com/tsd.asp
Product information for EU energy label
https://eprel.ec.europa.eu/qr/1115756
FCC-B Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the measures listed below:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/television technician for help
Notice 1
The changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Notice 2
Shielded interface cables and AC power cord, if any, must be used in order to
comply with the emission limits.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including interference that
may cause undesired operation
ASRock Contact Information
ASRock America, Inc.
Address : 13848 Magnolia Ave, Chino, CA91710, U.S.A.
Phone: +1-909-590-8308
Technical Support
Phone: +1-909-590-8308
Online Support https://event.asrock.com/tsd.asp
WEEE Statement
Under the European Union (“EU”) Directive on Waste Electrical and Electronic
Equipment, Directive 2012/19/EU, products of “electrical and electronic
equipment” cannot be discarded as municipal waste anymore and manufacturers of
covered electronic equipment will be obligated to take back such products at
the end of their useful life
Chemical Substances Information
In compliance with chemical substances regulations, such as the EU REACH
Regulation (Regulation EC No. 1907/2006 of the European Parliament and the
Council), ASRock provides the information of chemical substances in products
at:
RoHS Statement
Japan JIS C 0950 Material Declaration
A Japanese regulatory requirement, defined by specification JIS C 0950,
mandates that manufacturers provide material declarations for certain
categories of electronic products offered for sale after July 1, 2006.
India RoHS
This product complies with the “India E-waste (Management and Handling) Rule
2016” and prohibits use of lead, mercury, hexavalent chromium, polybrominated
biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1
weight % and 0.01 weight % for cadmium, except for the exemptions set in
Schedule 2 of the Rule
The terms HDMI, HDMI High-Definition Multimedia Interface, HDMI trade dress and the HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
Copyright and Trademarks Notice
Copyright © ASRock Inc. All rights reserved. The ASRock logo used is a
registered trademark of ASRock Inc. All other marks and names mentioned may be
trademarks of their respective owners. No warranty as to accuracy or
completeness is expressed or implied. ASRock reserves the right to make
changes to this document without prior notice.
Technical Support
If a problem arises with your product and no solution can be obtained from the
user’s manual,
please contact your place of purchase or local distributor. Alternatively,
please visit
https://www.asrock.com for further guidance.
Copyright Notice
No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.
Products and corporate names appearing in this documentation may or may not be
registered trademarks or copyrights of their respective companies, and are
used only for identification or explanation and to the owners’ benefit,
without intent to infringe.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Disclaimer
Because the monitor specifications and the firmware might be updated, the
content of this documentation will be subject to change without notice. In
case any modifications of this documentation occur, the updated version will
be available on ASRock’s website without further notice. If you require
technical support related to this motherboard, please visit our website for
specific information about the model you are using. You may find the latest
monitor support list on ASRock’s website as well.
ASRock Website: http://www.asrock.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>