LIVEX LIGHTING 42657 15-Light Satin Brass Modern-Contemporary Chandelier Instruction Manual

June 9, 2024
Livex Lighting

42657 15-Light Satin Brass Modern-Contemporary Chandelier
Instruction Manual

42657 15-Light Satin Brass Modern-Contemporary Chandelier

ASSEMBLING & INSTALLATION INSTRUCTIONS
The drawing shown may not exactly match the product enclosed.
However, the installation instructions do apply to this product.
42657 42658

  • WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
  • ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR.

ASSEMBLING THE FIXTURE (Fig.1)

  1. Shut off the power at the circuit breaker box. Remove old fixture and all hardware from Junction Box. Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation.

  2. By measuring, determine correct distance hole in mounting plate, then drilled three holes(by measuring distance hole) in the ceiling at junction box of side; raise the plastic anchor insert the hole. Attach the mounting plate to the junction box with two junction box screws and three wood screws as shown, tighten screws securely with the screwdriver. The side of the mounting plate marked “GND” must face out. The junction box is not included.

  3. By measuring, determine correct cord length of needed for proper hanging height, then lock it securely with small screw. NOTE: SLIDE WIRE CLIP TO THE PROPER POSITION, THEN YOU MAY PROPERLY CUT THE CORD IS TOO LONG PARTS. CONNECT THE ELECTRICAL WIRES AS SHOWN IN FIG.2.

  4. While holding the lamp body towards the ceiling, connect the electrical wires as Shown in Fig.2, making sure that all wire nuts are secured. You may have to wrap the connections with electrical tape. If your outlet has a ground wire (green or bare copper), connect the fixture ground wire to it. Otherwise connect fixture’s ground wire directly to the Mounting strap with the green screw provided. After wires are connected, tuck them carefully inside the Junction Box.

  5. Raise the lamp body(A) onto the junction box, aligning the pipe thread on mounting plate with mounting hole in canopy and lock it securely with the round nut(B).

  6. Raise the outside lamp holder into the top ring of the shade(E, 6pcs), lock it securely with the check ring until tight.

  7. Install the light bulbs(Not included) in accordance with the fixture’s specifications.
    NOTE: DO NOT EXCEED THE SPECIFIED WATTAG!

  8. Raise the center lamp holder frame insert the shade (C,1pc), aligning the end bracket hole of the top shade with the top screw hole of the lamp holder frame, lock it securely with the screws until tight. Using the same method install the middle lamp holder frame and shade(D,3pcs).

Your installation is now complete. Return power to the junction box the fixture.

LIVEX LIGHTING 42657 15-Light Satin Brass Modern-Contemporary Chandelier -
1

Thank you for purchasing a LIVEX product.
Need assistance with parts or assembly?
Please call customer service at: 800-761-8056

Or visit us on-line at:WWW.LIVEXLIGHTING.COM
©COPYRIGHT ALL RIGHTS RESERVED.LIVEX  LIGHTING, INC.DOC
20211142657

Documents / Resources

| LIVEX LIGHTING 42657 15-Light Satin Brass Modern-Contemporary Chandelier [pdf] Instruction Manual
42657, 42658, 42657 15-Light Satin Brass Modern-Contemporary Chandelier, 42657, 15-Light Satin Brass Modern-Contemporary Chandelier, Satin Brass Modern-Contemporary Chandelier, Brass Modern-Contemporary Chandelier, Modern- Contemporary Chandelier, Contemporary Chandelier, Chandelier
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Livex Lighting User Manuals

Related Manuals