TCL P210FLG Front Load Washing Machine Owner’s Manual

TCL P210FLG Front Load Washing Machine

• Before using your washing machine. Please read this manual carefully and keep it for future reference.
• This manual shall also be available by sending E-mail to client.
• The drawings in this manual are for instruction only.it may be vary from the model you buy.

Products Specification

P arame t er / Capac i ty| Inverter Motor Series
---|---
10kg
Model| P210FLG
Voltage| 220-240V-/50Hz
Rate d Power| 1900W
Water Pressure| O.OS-0.8MPa
Outer Dimension (W’D”H)mm| 590660850

NOTE:

1. All the pictures in the manual a re used for schematic only. It may be different from the machine you buy.
2. The actual function and the data in kind prevail.

Overview of Washing Machine

SAVE THESE INSTRUCTIONS
THE MACHINE IS HOUSEHOLD USE ONLY

Install Washing Machine

NOTE
We recommend that your new washer should to installed by a qualified appliance technician. If you feel that you have the skills to install the washer, please read the installation instructions carefully before installing.

Tools needed

You may need to have the following tools to help you in the installation of your washer:

• Scissors
• Gloves
• Pliers
• Spanner
• Standard Screwdriver

Unpacking the washing machine

Unpacking your washing machine and check if is there any damage during the transportation. Also make sure that all the the items(as shown below) in the attached bag are received. If there is any damage to the washing machine during the transportation. Or any item is missing or damaged, please contact the local dealer immediately.
“‘If washing machine is not double inlet, the machine does not have the hot inlet hose.

Select the location

Before installing the washer, the location characterized as follows shall be selected:

• Rigid,dry,and level surface(if not level. Please make it level with reference to the following figure “Adjustable Leg”},
• Avoid direct sun light.
• Sufficient ventilation.
• The ambient temperature shall be between 0-40’C.
• The ambient humidity shall be below 95%(When the temperature is 25’C).
• Keep far away from the heat resources such as coal or gas. Make sure that the washer will not stand on power cord. Do not install the washer on the carpet floor.

Remove transit bolts

Before using this washing machine, transit bolls must be removed from the backside of this machine. Please take the following steps to remove the bolts:
Keep the transit bolts properly for further use.

Level the washing machine

Install or place the washing machine under the environmental temperature of not less than 0 degree C but not outdoors, for it may damage the programming controller.
Note: ln order to facilitate installation, the factory status of the foot may not be all locked. please be sure lo lock all four feel before adjusting the level

CAUTION:

1. The machine must be perfectly leveled and stabilized when the four supporting feet are close to the ground. Lower the feet as much as possible on the basis that the machine is leveled.
2. improper leveling adjustment may cause loud noise, machine vibrating, machine displacement and other abnormal phenomena.
3. Air venal is designed on the bottom of the machine (prevent blockage). Install the washing machine on solid, smooth and skid-proof ground. Do not place the washing machine on soft blanket or wooden floor, or various desktops and stands, in case of unnecessary injury.

Connection

Connect the inlet hose

1. Connect the inlet hose to tap and fasten it anticlockwise.
2. Connect the other end of the inlet hose to the inlet valve at the backside of the washing machine and fasten the hose tightly clockwise. when there is a inlet at the back of the machine.it must be connected to a cold water supply. If there are two inlet valve.one is connected to a cold water supply and the other is connected to a hot water supply. Follow the indication of the picture below to complete the connection.

NOTE

• If there is any leakage with hose after the connection. then repeat the steps to connect inlet hose,
• Do not bend the hose.
• Check for inlet hose connection carefully before using the washer each time.

Connect the drain hose

1. The drain hose shall be placed at a height of 65-100cm above the floor, otherwise, it can cause poor drainage.
2. You can use the supplied drain hose support bracket to loop the drain hose down into the wall. Standpipe or laundry tub.
3. Take care to ensure all hose connections are tight.

NOTE:
The end of the drain hose cannot be immersed in water for the washer to work properly.
Connect the power

1. As the maximum current through the unit is 10A when you are using its heating function, please make sure the power supply system (current, power voltage and wire) at your home can meet the normal loading requirements of the electrical appliances.
2. Please connect the power to a socket which is correctly installed and properly earthed.
3. Make sure the power voltage at your plate is same to that in X the machine’s rated voltage.
4. Power plug must match the socket.
5. Do not use multi-purpose plug or socket as extension cord.
6. Do not connect and pull out plug with wet hands.
7. When pulling out the plug, hold the plug tightly and then pull it out. Do not pull power cord forcibly.
8. If power cord is damaged or has any sign of being broken, special power cord must be selected or purchased from its manufacturer or service center for replacement.

WARNING

• This machine must be earthed properly. If there is any short circuit, earthing can reduce the danger of electrical shock.
• Washing machine shall be operated in a circuit separate from other electrical appliances. Otherwise, power protector may be tripped or fuse may be burned out.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>