belkin WLS0503 Wemo Smart Light Switch and Wemo Smart Dimmer Instructions
- June 9, 2024
- belkin
Table of Contents
belkin WLS0503 Wemo Smart Light Switch and Wemo Smart Dimmer
Wemo Smart Light Switch & Wemo Smart Dimmer Regulatory Information and Safety Notices
The following paragraphs are required by the FCC and prove that this product meets all regulatory limits with regard to radio interference and radiation exposure. If you use this product as intended, you will have no issues with either.
FCC Statement
DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC
COMPATIBILITY
We, Belkin International, Inc., of 555 S Aviation Blvd Suite 180, EI Segundo,
CA 90245, declare under our sole responsibility that the products, WLS0503 and
WDS070, to which this declaration relates, comply with Part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the distance between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Radiation Exposure Statement
- This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
- This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
- This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
- Innovation, Science and Economic Development Canada Statement:
This device complies with ISED’s license-exempt RSS standards. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure. Note that this is not intended to prohibit transmission of control or signaling information, or the use of repetitive codes where required by the technology.
- This device and its antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with ISED multi-transmitter product procedures.
- This device has been designed to operate with an antenna having a maximum gain of 1.3 dBi at 2.4 GHz for WLS0503, and 0.8 dBi at 2.4 GHz for WDS070. Antenna having a higher gain is strictly prohibited per regulations of ISED. The required antenna impedance is 50 ohms.
- The maximum antenna gain to comply with the EIRP limit provided in the table below.
Radiation Exposure Statement
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and your body.
System Requirements:
Thread support requires HomePod mini or Apple TV 4K Apple HomeKit
General Specifications
- Input Electrical Rating: 120V~, 60Hz
- Max Output Electrical Rating: 120V~, Resistive Load, 600W Incandescent (WLS0503), 400W Incandescent (WDS070)
- Thread: 2.4 GHz 802.15.4
- BLE: 2.4 GHz 802.15.1
- Operating Temperature: 0 – 40° C
**Care
**
- Use dry cloth on exterior of the device. To avoid shock hazard and/or damage to device, DO NOT use any liquid solution.
Caution
- Risk of Electric Shock – More than one disconnected switch may be required to de-energize the equipment before servicing.
- For residential and Indoor Dry Location Use Only.
- To reduce the risk of overheating and possible damage to other equipment, do not install to control a receptacle, a motor-operated appliance, a fluorescent lighting fixture, or a transformer supplied appliance.
- For supply connections, use 14 AWG or 12 AWG wires rated for at least 90C.
- Changes or modifications not expressly approved by party responsible for compliance could void the user’s authority to operate the equipment.
- To avoid any risk or hazard that may be caused due to the end product connected to Wemo Smart Light Switch and Wemo Smart Dimmer, please read and understand the operation of the connected equipment before operating.
- If any of the above instructions are not followed, or the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.
For support, please visit: wemo.com/support.html
THIS DOCUMENT & THE INFORMATION IN IT ARE THE CONFIDENTIAL PROPERTY OF BELKIN INTERNATIONAL AND MUST NOT BE COPIED, REPRODUCED OR USED IN ANY MANNER WITHOUT THE WRITTEN CONSENT OF BELKIN CORPORATION. IT MUST BE RETURNED UPON REQUEST
- DO NOT PRINT DIE LINES, PRINTERS NOTES
Business Unit: NET-Networking
Program Manager:
Packaging Engineer: Brian Byrd
Retail Outside Dimension (Including Hang Tab)
- L x W x D (in):
- L x W x D (mm):
DIE/MATERIAL SPECS
- Material: 80 gsm woodfree paper
- Blank Size (in): 7.295 x 4.675
- Blank Size (mm): 185.297 x 118.756
This dieline works for following skus (if any):
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>