belkin WLS0503 Smart Light Switch with Thread User Manual
- June 9, 2024
- belkin
Table of Contents
belkin WLS0503 Smart Light Switch with Thread
- See the virtual setup guide
- Scan this QR code to see support and videos online.
- Or go to wemo.com/lightswitch
What’s included
- Cover plate
- Light switch and screws
- Jumper wire and wire nut
LINE / LOAD
Wire label
You’ll only need this if you are replacing a 3-way light switch, where two
switches control one light
What you’ll need
- iPhone or iPad on latest OS for setup and control
- Home hub to access devices while you are away from home
Set up one of these devices as a home hub: Apple TV, HomePod, or iPad
Learn how to set up a home hub: support.apple.com/en-
us/HT207057
Neutral wire
These wires are typically white and can be found in your electrical box.
Note : If you do not have a neutral wire, your house is not compatible
with the Wemo Smart Light Switch.
Tools
Setup instructions
WARNING! Risk of electric shock
Incorrect installation could be dangerous or illegal. You might need to turn off multiple breakers/fuses for safe installation. Please call a professional electrician if you are unfamiliar or uncomfortable with electrical work
-
Turn off the power
-
Shut off power to the switch you’re replacing at your fuse panel or circuit breaker
Confirm that power is off -
Remove the cover plate from the existing switch.
-
Use a voltage tester to test BOTH sides of the switch. You may need to turn off more than one circuit breaker/fuse
-
Pull out existing switch
-
Unscrew the switch and gently pull it out of the wall.
-
Do not remove any of the wires yet
Pro Tip:
Take a picture of the wires in your wall to refer back to later -
Look for NEUTRAL wires
NEUTRAL wires are usually white. If you have them, we will direct you to connect them later in step 7. If you don’t have them, your house is not compatible with Wemo Smart Light Switch.
Note:
You may have a different number of neutral wires than shown.
Test the NEUTRAL wires
Use a voltage tester to check that there is no power in the NEUTRAL wires from neighboring circuits. If necessary, shut off additional circuits until no voltage is found -
Identify your existing switch
Single pole
If one switch controls one light, it is a single-pole switch
3-way
If two switches control the same light, they are both 3-way switches
4-way
If three switches control the same light, the one with 5 screws is a 4-way switch. The other two are 3-way switches.
Follow 3-way installation instructions
Wemo Smart Light Switch cannot replace a 4-way switch -
Remove existing switch
Disconnect the LINE and LOAD wires (usually black) from the existing light switch.
Note : Your existing switch, wires, and electrical box may look different and have different colors
Disconnect the GROUND wire from the switch (usually bare copper or green). Remove wire nuts from the white NEUTRAL wires
-
Prepare Wemo Smart Light Switch and wires
Grab the cover plate from the top and pull down to snap it off of the Wemo Smart Light Switch
Loosen the black and red screws on the Wemo Smart Light Switch with a screwdriver.
Options for connecting wires -
Insert into holes
-
Insert the wire end into either of the holes near the screw.
-
Use a screwdriver to tightly screw the terminal screws back in. These will clamp down on the wire.
-
Hook around screw
-
Use pliers to bend the end of the wire clockwise. Hook it around the screw
-
Use a screwdriver to tightly screw the terminal screws back in
For the upcoming steps, choose your preferred option for connecting wires:
Note:
If needed, use pliers to strip the wire end to this length: -
Connect LINE, LOAD, GROUND, and NEUTRAL wires
-
Connect the LINE and LOAD wires from the wall (usually black) to the black and red screws on the light switch using your preferred method ( shown here).
Tighten each screw after inserting wire
Note:
Either wire can be connected to either screw.
Connect the GROUND wires (usually bare copper or green) from the wall to the green screw on the switch
Connect the provided jumper wire from the silver screw on the light switch to the NEUTRAL wires in the wall with a wire nut
-
Install Wemo Smart Light Switch into the wall
Almost done! Tug each wire to ensure they are securely connected
Carefully tuck the wires behind the switch and into the box. Screw the light switch into the wall. Be careful not to over-tighten the screws
Pro Tip
Make sure to insulate any exposed wiring with electrical tape
Before snapping on the cover plate, you’ll notice an 8-digit setup code on the switch. You may need this during app setup. You can also find it in step 10 of this guide
Finally, snap the cover plate onto the switch
-
Turn on the power
Turn on power to your switch at your fuse panel or circuit breaker panel you turned off earlier.
Press the switch to put it in setup mode
-
The light will blink blue when it is ready
-
Add to the Apple Home app Unlock your phone.
-
Hold the upper back of your phone at the center of the switch
-
Adjust your phone angle until setup prompts appear on your phone
-
Follow prompts
Don’t see the prompts?
Add a new accessory in the Apple Home app and manually enter this 8-digit HomeKit Setup Code
FINISH SIZE
Enjoy your Wemo Smart Light Switch
- Control from Apple Home
- Use the Home app to turn your Wemo on and off, share control, and organize your smart devices into groups and rooms
- Use voice with Siri
- Make sure to name your Wemo how you’d like to call it. Then ask Siri on your iPhone, iPad, or HomePod to turn your Wemo on or off
- Create schedules and scenes
- Set your switch to automatically turn on or off at a particular time of day or when you leave or arrive home
Thread for quicker and more reliable control
- Thread is a new wireless technology built into Wemo. It connects smart home devices more quickly and reliably than Bluetooth or Wi-Fi.
- To take advantage of it, you’ll need an Apple HomePod mini or the latest Apple TV 4K. If you don’t have one of those, your Wemo will connect using Bluetooth. Learn more at wemo.com/thread
Restart and restore
- Restart
- Having setup or control issues?
- Press and hold (2 sec) the reset button until the light blinks white, then release.
- Restore
- If a restart doesn’t help, try restoring to factory settings.
- Press and hold (6 sec) the reset button until the light blinks red, then release.
What does the light tell me?
- Blinking White
- Setup mode – ready for app setup
- Blinking Blue
- Setup mode – ready for app setup
- Solid Blue or White (30 sec)
- Successfully connected
- Fast Blinking Green (6x)
- Wemo was identified by the Home app
- Fast Blinking Red (about 4x a sec)
- Your Wemo is overheating. Don’t worry, we turned it off to let it cool down. Unplug, wait 1 min, then plug back in.
Wiring diagrams
Single-pole wiring
3-way wiring
Note:
A 3-way configuration can also include 2 Wemo Smart Light Switches
References
- Set up your HomePod, HomePod mini, Apple TV, or iPad as a home hub - Apple Support
- Belkin Official Support - Wemo Smart Light Switch 3-Way, WLS0503 User Guide
- Thread networking - A new mesh technology for 2022 smart homes and smart devices.
- Warranty Center | Belkin: US
- Belkin Official Support - How to install Wemo Smart Light Switch 3-Way, WLS0503 to replace an existing 3-way switch
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>